ASSEMBLY INSTRUCTIONS TWO DOOR SPACESAVER WHITE ESPRESSO ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of the small parts. Care should be taken in unpacking and assembling this item to keep the small parts away from children. WARNING Young children can be seriously injured or killed, if furniture tips over. Don’t use this item for a TV stand. Use angle-braces or anchors to secure furniture to the wall.
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE THAN 25 POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST
TOOLS NEEDED FOR ASSEMBLY : FLAT & PHILIPS SCREWDRIVER (NOT INCLUDED) THE USE OF POWER SCREWDRIVER IS NOT RECOMMENED
STEP 1 STEP 1 1.Screw 4 cam bolts (A) into the pre-threaded holes on the top board (1) by using a Philips screwdriver. 2. Insert 4 wood dowels (C) into the dowel holes on the top board (1). 3. Attach the magnet (D) to the top board (1). 4. Insert 2 screws (O) through holes on the magnet (D) then tighten to top board (1) by using a Philip screwdriver. STEP 2 STEP 2 1.Screw 4 cam bolts (A) into the pre-threaded holes on the middle connection board (2) by using a Philips screwdriver. 2.
STEP 3 STEP 3 1.Screw 2 cam bolts (A) into the pre-threaded holes on the top left side panel (3) by using a Philips screwdriver. 2.Insert 4 wood dowels (C) into the dowel holes on the top left side panel (3). STEP 4 STEP 4 1. Screw 2 cam bolts (A) into the pre-threaded holes on the top right side panel (3) by using a Philips screwdriver. 2. Insert 4 wood dowels (C) into the dowel holes on the top right side panel (3).
STEP 5 STEP 5 1.Insert 8 wood dowels (C) into the dowel holes on the bottom left side panel (5). STEP 6 STEP 6 1.Insert 8 wood dowels (C) into the dowel holes on the bottom right side panel (6).
STEP 7 STEP 7 1.Insert 1 screw (M) through hole on the magnet plate (E) then tighten to left side door (15)by using a Philips screwdriver. 2.Attach knob (H) to the left side door (15) , insert 1 screw (J) through hole on the left side door (15) then tighten to knob (H) by using a Philips screwdriver. 3.Insert 2 pins (K) into the holes on each end of the left side door (15). STEP 8 STEP 8 1.
STEP 9 STEP 9 1.Attach the top shelf (7) and bottom shelf (8) to the top right side panel (4) by inserting cam bolts into cam lock holes and inserting wood dowels into dowel holes on the top shelf (7) and bottom shelf (8). 2.Insert 2 cam locks (B) into cam lock holes on the bottom shelf (8) then rotateclockwise to secure cam bolts in place by using a Philips screwdriver. 3.
STEP 11 STEP 11 1.Attach the top left side panel (3) to the pre-assembled top shelf (7) and bottom shelf (8) by inserting cam bolts into cam lock holes and inserting wood dowels into dowel holes on the top shelf (7) and bottom shelf (8). and rear top cross bar(10). 2.Insert 2 cam locks (B) into the cam lock holes on the bottom shelf (8) then rotate clockwise to secure cam bolts in place by using a Philips screwdriver. STEP 12 STEP 12 1.
STEP 13 STEP 13 1.Attach the bottom left side panel (5) to rear bottom cross bar (9) ,rear top cross bar (17)and front top cross bar (11) by inserting wood dowels into dowel holes on the rear bottomcross bar (9),rear top cross bar (17) and front top cross bar (11). 2.Insert 3 screws (Q) through the holes on the bottom left side panel (5) then tighten to rear bottom cross bar (9),rear top cross bar (17) and front top cross bar (11) by using a allen wrench. 3.
STEP 15 STEP 15 1.Insert 4 screws (P) through holes on the middle connection board (2) then tighten to the bottom left side panel (5) and bottom right side panel (6) by using a Philips screwdriver. STEP 16 STEP 16 1.Place the top portion onto the middle connection board (2) by inserting the wood dowels into the dowel holes and cam bolts into cam lock holes on the end of both top side panels (3),(4) 2.
STEP 17 STEP 17 1.Place the drawing with hole position on the wall that you desire to fix the spacesaver. 2.Drill 2 holes through the hole position on the drawing. 3.Insert 2 plastic anchors (F) into the holes. 4.Attach the spacesaver in place w/holes, then insert 2 long screws (G) through the holes on the back top cross bar (10) then tighten the spacesaver to the wall.
ENJOY YOUR NEW CABINET NOW ! Attention Adults: The cabinet should be checked periodically for damage or loose screws/parts. Take appropriate action necessary to correct the hazard such as tightening of screws and taking any damaged parts away from the children. Thank you for purchasing this item. We hope you enjoy it, and consider purchasing other items.