Use and Care guide
Table Of Contents
- Table of ContentsUse and care manual
- IMPORTANT SAFETY INSTRUCTIONS
- READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
- WARNING
- WARNING
- WARNING
- Risk of injury
- Risk of injury
- Grounding Instructions
- TV / Radio Interference
- Intended Use
- Child Safety
- Cleaning Safety
- Cooking Safety
- In Case of Fire
- Liquids
- Cooking Items
- Cooking Utensils
- Glass Tray / Turntable Ring
- Exhaust Mode Operation
- Thermometers
- Pacemakers
- State of California Proposition 65 Warnings:
- Fan Motor Operation
- Room Venting with Carbon Filter
- Causes of Damage
- Protecting the environment
- Getting Started
- Before Using the Appliance for the First Time
- Operation
- Setting the clock
- Setting the Kitchen Timer
- Operating the Ventilation Fan
- Turning the Surface Light on/off
- Turning the turntable on / off
- Operating the microwave
- 1. Enter the desired cooking duration with the number keys. The timer display will fill in from right to left. Example: To set a microwave cooking time of 20 minutes and 30 seconds, enter the numbers 2 0 3 0. START is blinking.
- 2. You can start microwave operation with the default power level 10 by touching START/ENTER, or - you can adjust the power level. Touch POWER LEVEL. The default power level ˜–‚‹ is blinking. The segments in the bar underneath the number displ...
- 3. Enter the desired power level using the number keys. ˜–and the selected power level and START are blinking in the display.
- 4. Touch START/ENTER to start microwave operation.
- Opening appliance door during operation
- Cancel operation
- Microwave power levels
- Suggestions for best results
- 1. Enter the desired cooking duration with the number keys. The timer display will fill in from right to left. Example: To set a microwave cooking time of 20 minutes and 30 seconds, enter the numbers 2 0 3 0. START is blinking.
- Adding cook time (ADD 30 SECONDS)
- Auto Defrost
- Setting Auto Defrost
- 1. Touch AUTO DEFROST once. š“”‚ and START are blinking and the à symbol lights up in the display.
- 2. Touch AUTO DEFROST repeatedly until the desired program number is shown in the display. Check the menu label at the bottom of the oven cavity or see program table below.
- 3. Touch START/ENTER. ‹.‹ lb is blinking in the display.
- 4. Enter the weight of the food using the number keys.
- 5. Touch START/ENTER to start the program.
- Note:
- Opening appliance door during operation
- Cancel operation
- Auto Defrost programs
- Tips for defrosting
- Defrosting suggestions for meat
- Sensor Reheat
- Setting Sensor Reheat
- 1. Touch SENSOR REHEAT once. †§ -‚ and START are blinking in the display.
- 2. Touch SENSOR REHEAT repeatedly until the desired program number is shown in the display. Check the menu label at the bottom of the oven cavity or see program table below.
- 3. Touch START/ENTER to start sensor reheat mode. The appliance starts sensing, SENS. lights up in the display. The microwave is operating during sensing.
- Note:
- Notes
- Cancel operation
- Sensor Reheat programs
- Reheat cooking suggestions
- Cooking Charts
- Cleaning and Maintenance
- 9 WARNING
- Cleaning
- Cleaning Guide
- Cleaning the oven vent filters
- NOTICE:
- 1. To remove the ventilation filters, release the catch by pulling it down with your finger. The filter will drop down at the front. Then pull filter towards you to remove it. The filter will drop out. Repeat for the 2nd filter.
- 2. Soak the ventilation filters in hot water using a mild detergent. Rinse well and shake to dry. You can also wash the filters in a dishwasher.
- 3. To reinstall the ventilation filter, slide the two pins at the rear side of the filter into the slots at the rear of the filter opening, then push up filter at the front until the catch locks in place with a click. Reinstall the 2nd filter using t...
- Maintenance
- Before Calling for Service
- THERMADOR® Support
- STATEMENT OF LIMITED PRODUCT WARRANTY
- ContenidoManual de instrucciones
- READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
