Datasheet
TS3A5018
SCDS189F –JANUARY 2005–REVISED MAY 2013
www.ti.com
Electrical Characteristics for 3.3-V Supply
(1)
V
+
= 3 V to 3.6 V, T
A
= –40°C to 85°C (unless otherwise noted)
PARAMETER SYMBOL TEST CONDITIONS T
A
V
+
MIN TYP MAX UNIT
Analog Switch
Analog signal V
COM
, V
NO
,
0 V
+
V
range V
NC
25°C 7 10
ON-state 0 ≤ (V
NC
or V
NO
) ≤ V
+
, Switch ON,
r
on
3 V Ω
resistance I
COM
= –32 mA, See Figure 19
Full 12
ON-state 25°C 0.3 0.8
resistance V
NC
or V
NO
= 2.1 V, Switch ON,
Δr
on
3 V Ω
match between I
COM
= –32 mA, See Figure 19
Full 1
channels
ON-state 25°C 5 7
0 ≤ (V
NC
or V
NO
) ≤ V
+
, Switch ON,
resistance r
on(flat)
3 V Ω
I
COM
= –32 mA, See Figure 19
Full 8
flatness
V
NC
or V
NO
= 1 V, 25°C –0.1 0.05 0.1
V
COM
= 3 V,
Switch OFF,
or 3.6 V
See Figure 20
Full –0.2 0.2
V
NC
or V
NO
= 3 V,
NC, NO
V
COM
= 1 V,
I
NC(OFF)
,
OFF leakage μA
I
NO(OFF)
V
NC
or V
NO
= 0 to 3.6 V, 25°C –2 0.05 2
current
V
COM
= 3.6 V to 0,
Switch OFF,
or 0 V
See Figure 20
Full –10 10
V
NC
or V
NO
= 3.6 V to 0,
V
COM
= 0 to 3.6 V,
V
COM
= 1 V, 25°C –0.1 0.05 0.1
V
NC
or V
NO
= 3 V,
Switch OFF,
or 3.6 V
See Figure 20
Full –0.2 0.2
V
COM
= 3 V,
COM
V
NC
or V
NO
= 3 V,
OFF leakage I
COM(OFF)
μA
V
COM
= 0 to 3.6 V, 25°C –2 0.05 2
current
V
NC
or V
NO
= 3.6 V to 0,
Switch OFF,
or 0 V
See Figure 20
Full –10 10
V
COM
= 3.6 V to 0,
V
NC
or V
NO
= 0 to 3.6 V,
V
NC
or V
NO
= 1 V, 25°C –0.1 0.05 0.1
NC, NO V
COM
= Open,
I
NC(ON)
, Switch ON,
ON leakage or 3.6 V μA
I
NO(ON)
See Figure 21
Full –0.2 0.2
current V
NC
or V
NO
= 3 V,
V
COM
= Open,
V
COM
= 1 V, 25°C –0.1 0.05 0.1
COM V
NC
or V
NO
= Open,
Switch ON,
ON leakage I
COM(ON)
or 3.6 V μA
See Figure 21
Full –0.2 0.2
current V
COM
= 3 V,
V
NC
or V
NO
= Open,
Digital Control Inputs (IN, EN)
(2)
Input logic high V
IH
Full 2 V
+
V
Input logic low V
IL
Full 0 0.8 V
25°C –1 0.05 1
Input leakage
I
IH
, I
IL
V
I
= V
+
or 0 3.6 V μA
current
Full –1 1
(1) The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
(2) All unused digital inputs of the device must be held at V
+
or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: TS3A5018