Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsPMICsPMIC - LDO voltage regulator Positive, fixed SON 6 (2x2)

TPS799xxDDC

TSOT23-5

(TOPVIEW)

OUT

GND

TPS799xxYZU

WCSP

(TOPVIEW)

C3 C1

A3 A1

OUT

GND

TPS79901YZU

WCSP

(TOPVIEW)

OUT

C3 C1

A3 A1

TPS79901DDC

TSOT23-5

(TOPVIEW)

OUT

GND

TPS799xxDRV

2mmx2mmSON-6

(TOPVIEW)

N/C

OUT

GND

TPS79901DRV

2mmx2mmSON-6

(TOPVIEW)

N/C

OUT

GND

TPS799xx

www.ti.com

SBVS056J –JANUARY 2005–REVISED AUGUST 2010

200mA, Low Quiescent Current, Ultra-Low Noise, High PSRR

Low Dropout Linear Regulator

Check for Samples: TPS799xx

FEATURES

DESCRIPTION

• 200mA Low Dropout Regulator with EN

The TPS799xx family of low-dropout (LDO)

low-power linear regulators offer excellent AC

• Low I

: 40mA

performance with very low ground current. High

• Multiple Output Voltage Versions Available:

power-supply rejection ratio (PSRR), low noise, fast

– Fixed Outputs of 1.2V to 4.5V Using

start-up, and excellent line and load transient

Innovative Factory EEPROM Programming

response are provided while consuming a very low

40mA (typical) ground current. The TPS799xx is

– Adjustable Outputs from 1.20V to 6.5V

stable with ceramic capacitors and uses an advanced

• High PSRR: 66dB at 1kHz

BiCMOS fabrication process to yield dropout voltage

• Ultra-low Noise: 29.5mV

RMS

typically 100mV at 200mA output. The TPS799xx

uses a precision voltage reference and feedback loop

• Fast Start-Up Time: 45ms

to achieve overall accuracy of 2% over all load, line,

• Stable with a Low-ESR, 2.0mF Typical Output

process, and temperature variations. It is fully

Capacitance

specified from T

= –40°C to +125°C and is offered in

• Excellent Load/Line Transient Response

low profile ThinSOT23, Wafer Chip-Scale (WCSP),

and 2mm × 2mm SON packages, ideal for wireless

• 2% Overall Accuracy (Load/Line/Temp)

handsets and WLAN cards.

• Very Low Dropout: 100mV

• ThinSOT-23, WCSP, and 2mm × 2mm SON-6

Packages

APPLICATIONS

• Cellular Phones

• Wireless LAN, Bluetooth

• VCOs, RF

• Handheld Organizers, PDAs

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2Bluetooth is a registered trademark of Bluetooth SIG, Inc.

3All other trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (34 pages)

PAGE 1
TPS799xx www.ti.com SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 200mA, Low Quiescent Current, Ultra-Low Noise, High PSRR Low Dropout Linear Regulator Check for Samples: TPS799xx FEATURES DESCRIPTION • • • The TPS799xx family of low-dropout (LDO) low-power linear regulators offer excellent AC performance with very low ground current.
PAGE 2
TPS799xx SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure.
PAGE 3
TPS799xx www.ti.com SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 ELECTRICAL CHARACTERISTICS Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.3V or 2.7V, whichever is greater; IOUT = 1mA, VEN = VIN, COUT = 2.2mF, CNR = 0.01mF, unless otherwise noted. For TPS79901, VOUT = 3.0V. Typical values are at TJ = +25°C. PARAMETER TEST CONDITIONS (1) VIN Input voltage range VFB Internal reference (TPS79901) MAX 6.5 V 1.193 1.217 Output voltage range (TPS79901) V VFB 6.
PAGE 4
TPS799xx SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 www.ti.com DEVICE INFORMATION FUNCTIONAL BLOCK DIAGRAMS IN OUT IN OUT 400Ω 400Ω 2µA Current Limit Overshoot Detect Thermal Shutdown EN 3.3MΩ Current Limit Overshoot Detect Thermal Shutdown EN UVLO UVLO Quickstart 1.193V Bandgap 1.193V Bandgap NR FB 500k 500k GND GND Figure 1. Fixed Voltage Versions Figure 2.
PAGE 5
TPS799xx www.ti.com SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 TYPICAL CHARACTERISTICS Over operating temperature range (TJ= –40°C to +125°C), VIN = VOUT(TYP) + 0.3V or 2.7V, whichever is greater; IOUT = 1mA, VEN = VIN, COUT = 2.2mF, CNR = 0.01mF, unless otherwise noted. For TPS79901, VOUT = 3.0V. Typical values are at TJ = +25°C. LOAD REGULATION LINE REGULATION 28.50 1.0 21.38 0.8 IOUT = 100mA Change in VOUT (%) Change in VOUT (mV) 0.6 14.25 TJ = +25°C 7.13 TJ = −40°C 0 −7.13 −14.
PAGE 6
TPS799xx SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) Over operating temperature range (TJ= –40°C to +125°C), VIN = VOUT(TYP) + 0.3V or 2.7V, whichever is greater; IOUT = 1mA, VEN = VIN, COUT = 2.2mF, CNR = 0.01mF, unless otherwise noted. For TPS79901, VOUT = 3.0V. Typical values are at TJ = +25°C. GROUND PIN CURRENT vs INPUT VOLTAGE TPS799285 GROUND PIN CURRENT vs JUNCTION TEMPERATURE 60 60 50 50 VIN = 3.2V VIN = 5.
PAGE 7
TPS799xx www.ti.com SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 TYPICAL CHARACTERISTICS (continued) Over operating temperature range (TJ= –40°C to +125°C), VIN = VOUT(TYP) + 0.3V or 2.7V, whichever is greater; IOUT = 1mA, VEN = VIN, COUT = 2.2mF, CNR = 0.01mF, unless otherwise noted. For TPS79901, VOUT = 3.0V. Typical values are at TJ = +25°C. TPS799285 POWER-SUPPLY RIPPLE REJECTION vs FREQUENCY (VIN – VOUT = 0.5V) TPS799285 POWER-SUPPLY RIPPLE REJECTION vs FREQUENCY (VIN – VOUT = 0.
PAGE 8
TPS799xx SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) Over operating temperature range (TJ= –40°C to +125°C), VIN = VOUT(TYP) + 0.3V or 2.7V, whichever is greater; IOUT = 1mA, VEN = VIN, COUT = 2.2mF, CNR = 0.01mF, unless otherwise noted. For TPS79901, VOUT = 3.0V. Typical values are at TJ = +25°C. POWER-SUPPLY RIPPLE REJECTION vs VIN – VOUT, IOUT = 100mA POWER-SUPPLY RIPPLE REJECTION vs VIN – VOUT, IOUT = 200mA 90 90 0.
PAGE 9
TPS799xx www.ti.com SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 TYPICAL CHARACTERISTICS (continued) Over operating temperature range (TJ= –40°C to +125°C), VIN = VOUT(TYP) + 0.3V or 2.7V, whichever is greater; IOUT = 1mA, VEN = VIN, COUT = 2.2mF, CNR = 0.01mF, unless otherwise noted. For TPS79901, VOUT = 3.0V. Typical values are at TJ = +25°C. TPS799285 TURN-ON RESPONSE (VEN = VIN) RLOAD = 19W COUT = 2.2mF TPS799285 ENABLE RESPONSE VIN = 3.85V RLOAD = 19W COUT = 2.
PAGE 10
TPS799xx SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 www.ti.com APPLICATION INFORMATION The TPS799xx family of LDO regulators combines the high performance required of many RF and precision analog applications with ultra-low current consumption. High PSRR is provided by a high gain, high bandwidth error loop with good supply rejection at very low headroom (VIN – VOUT).
PAGE 11
TPS799xx www.ti.com Noise can be referred to the feedback point (FB pin) such that with CNR = 0.01mF total noise is approximately given by Equation 1: 10.5mVRMS VN = x VOUT V (1) The TPS79901 adjustable version does not have the noise-reduction pin available, so ultra-low noise operation is not possible. Noise can be minimized according to the above recommendations.
PAGE 12
TPS799xx SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 www.ti.com THERMAL INFORMATION Thermal Protection Thermal protection disables the output when the junction temperature rises to approximately +165°C, allowing the device to cool. When the junction temperature cools to approximately +145°C the output circuitry is again enabled. Depending on power dissipation, thermal resistance, and ambient temperature, the thermal protection circuit may cycle on and off.
PAGE 13
TPS799xx www.ti.com SBVS056J – JANUARY 2005 – REVISED AUGUST 2010 REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision I (November, 2007) to Revision J • Page Replaced the Dissipation Ratings table with the Thermal Information table ........................................................................
PAGE 14
PACKAGE OPTION ADDENDUM www.ti.
PAGE 15
PACKAGE OPTION ADDENDUM www.ti.
PAGE 16
PACKAGE OPTION ADDENDUM www.ti.
PAGE 17
PACKAGE OPTION ADDENDUM www.ti.
PAGE 18
PACKAGE OPTION ADDENDUM www.ti.
PAGE 19
PACKAGE OPTION ADDENDUM www.ti.
PAGE 20
PACKAGE OPTION ADDENDUM www.ti.
PAGE 21
PACKAGE OPTION ADDENDUM www.ti.
PAGE 22
PACKAGE OPTION ADDENDUM www.ti.com 29-May-2013 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties.
PAGE 23
PACKAGE MATERIALS INFORMATION www.ti.com 12-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS79901DDCR Package Package Pins Type Drawing SOT DDC 5 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS79901DDCT SOT DDC 5 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS79901DRVR SON DRV 6 3000 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 TPS79901DRVT SON DRV 6 250 179.
PAGE 24
PACKAGE MATERIALS INFORMATION www.ti.com 12-Oct-2013 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS79915DDCR SOT DDC 5 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS79915DDCT SOT DDC 5 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS79915YZUR DSBGA YZU 5 3000 180.0 8.4 1.07 1.42 0.74 4.0 8.0 Q1 TPS79915YZUT DSBGA YZU 5 250 180.0 8.4 1.07 1.42 0.74 4.0 8.
PAGE 25
PACKAGE MATERIALS INFORMATION www.ti.com 12-Oct-2013 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS799285YZUT DSBGA YZU 5 250 180.0 8.4 1.07 1.42 0.74 4.0 8.0 Q1 TPS79928DDCR SOT DDC 5 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS79928DDCT SOT DDC 5 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS79928DRVR SON DRV 6 3000 179.0 8.4 2.2 2.2 1.2 4.0 8.
PAGE 26
PACKAGE MATERIALS INFORMATION www.ti.com 12-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS79901DDCR SOT DDC 5 3000 203.0 203.0 35.0 TPS79901DDCT SOT DDC 5 250 203.0 203.0 35.0 TPS79901DRVR SON DRV 6 3000 203.0 203.0 35.0 TPS79901DRVT SON DRV 6 250 203.0 203.0 35.0 TPS79901YZUR DSBGA YZU 5 3000 210.0 185.0 35.0 TPS79901YZUT DSBGA YZU 5 250 210.0 185.0 35.
PAGE 27
PACKAGE MATERIALS INFORMATION www.ti.com 12-Oct-2013 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS79915YZUR DSBGA YZU 5 3000 210.0 185.0 35.0 TPS79915YZUT DSBGA YZU 5 250 210.0 185.0 35.0 TPS799185DDCR SOT DDC 5 3000 203.0 203.0 35.0 TPS799185DDCT SOT DDC 5 250 203.0 203.0 35.0 TPS799185YZUR DSBGA YZU 5 3000 182.0 182.0 17.0 TPS799185YZUT DSBGA YZU 5 250 182.0 182.0 17.0 TPS79918DDCR SOT DDC 5 3000 203.
PAGE 28
PACKAGE MATERIALS INFORMATION www.ti.com 12-Oct-2013 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS79928DRVR SON DRV 6 3000 203.0 203.0 35.0 TPS79928DRVT SON DRV 6 250 203.0 203.0 35.0 TPS79928YZUR DSBGA YZU 5 3000 210.0 185.0 35.0 TPS79928YZUT DSBGA YZU 5 250 210.0 185.0 35.0 TPS79930DDCR SOT DDC 5 3000 203.0 203.0 35.0 TPS79930DDCT SOT DDC 5 250 203.0 203.0 35.0 TPS79930YZUR DSBGA YZU 5 3000 210.0 185.
PAGE 29
PAGE 30
PAGE 31
PAGE 32
PAGE 33
D: Max = 1.367 mm, Min =1.307 mm E: Max = 1.001 mm, Min = 0.
PAGE 34
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.