Datasheet

  
  
µ  

SLOS193B − FEBRUARY 1997 − REVISED MAY 2004
41
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2064M electrical characteristics at specified free-air temperature, V
CC
±
= ±5 V (unless
otherwise noted) continued)
PARAMETER TEST CONDITIONS
T
A
†
TLE2064M
TLE2064AM
TLE2064BM
UNIT
A
MIN TYP MAX
V
O
= 0 to 2 V,
R
L
= 100 Ω
25°C 0.75 45
A
VD
Large-signal differential voltage
D and N
V
O
= 0 to 2 V, R
L
= 100 Ω
Full range
0.25
V/mV
A
VD
Large-signal differential voltage
amplification
D and N
packages
V
O
= 0 to −2 V,
R
L
= 100 Ω
25°C 0.4 3
V/mV
amplification
packages
V
O
= 0 to −2 V
,
R
L
= 100 Ω
Full range
0.15
r
i
Input resistance 25°C 10
12
Ω
c
i
Input capacitance 25°C 4 pF
z
o
Open-loop output impedance I
O
= 0 25°C 560 Ω
CMRR
Common-mode rejection ratio
V
IC
= V
ICR
min,
R
S
= 50 Ω
25°C 65 82
dB
CMRR Common-mode rejection ratio V
IC
= V
ICR
min
,
R
S
= 50 Ω
Full range
60
dB
k
SVR
Supply-voltage rejection ratio (∆V
CC
/∆V
IO
)
V
CC±
=
±
5 V to
±
15 V,
25°C 75 93
dB
k
SVR
Supply-voltage rejection ratio (∆V
CC±
/∆V
IO
)
V
CC±
= ±5 V to ± 15 V,
R
S
= 50 Ω
Full range 65
dB
I
CC
Supply current (four amplifiers)
25°C 1.12 1.3
mA
I
CC
Supply current (four amplifiers)
V
O
= 0,
No load
Full range 1.3
mA
∆I
CC
Supply-current change over operating
temperature range (four amplifiers)
V
O
= 0,
No load
Full range 144 µA
V
O1
/V
O2
Crosstalk attenuation A
VD
= 1000, f = 1 kHz 25°C 120 dB
†
Full range is −55°C to 125°C.
TLE2064M operating characteristics, V
CC±
= ±5 V, T
A
= 25°C
PARAMETER TEST CONDITIONS
TLE2064M
TLE2064AM
TLE2064BM
UNIT
MIN TYP MAX
SR Slew rate at unity gain (see Figure 1) R
L
= 10 kΩ, C
L
= 100 pF 3.4 V/µs
V
n
Equivalent input noise voltage (see Figure 2)
f = 10 Hz, R
S
= 20 Ω 59
nV/√Hz
V
n
Equivalent input noise voltage (see Figure 2)
f = 1 kHz,
R
S
= 20 Ω 43
nV/√Hz
V
N(PP)
Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 10 Hz 1.1 µV
I
n
Equivalent input noise current f = 1 kHz 1 fA/√Hz
THD
Total harmonic distortion
A
VD
= 2,
f = 10 kHz,
0.025%
THD Total harmonic distortion
A
VD
= 2,
V
O(PP)
= 2 V
,
f = 10 kHz,
R
L
= 10 kΩ
0.025%
B
1
Unity-gain bandwidth (see Figure 3)
R
L
= 10 kΩ, C
L
= 100 pF 1.8
MHz
B
1
Unity-gain bandwidth (see Figure 3)
R
L
= 600 Ω
, C
L
= 100 pF 1.3
MHz
t
s
Settling time
ε = 0.1% 5
s
t
s
Settling time
ε = 0.01%
10
µs
B
OM
Maximum output-swing bandwidth A
VD
= 1, R
L
= 10 kΩ 140 kHz
φ
m
Phase margin at unity gain (see Figure 3)
R
L
= 10 kΩ, C
L
= 100 pF 58°
φ
m
Phase margin at unity gain (see Figure 3)
R
L
= 600 Ω, C
L
= 100 pF 75°