Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Comparator Multi-purpose MOS, Open drain SOIC 8

 

    

SLCS115E − DECEMBER 1986 − REVISED JULY 2003

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

POST OFFICE BOX 1443

• HOUSTON, TEXAS 77251−1443

D Very Low Power ...110 µW Typ at 5 V

D Fast Response Time ...t

PLH

= 2.5 µs Typ

With 5-mV Overdrive

D Single Supply Operation:

TLC393C ...3 V to 16 V

TLC393I ...3 V to 16 V

TLC393Q ...4 V to 16 V

TLC393M ...4 V to 16 V

TLC193M ...4 V to 16 V

D On-Chip ESD Protection

description

The TLC193 and TLC393 consist of dual

independent micropower voltage comparators

designed to operate from a single supply. They

are functionally similar to the LM393 but uses

one-twentieth the power for similar response

times. The open-drain MOS output stage

interfaces to a variety of loads and supplies. For

a similar device with a push-pull output

configuration (see the TLC3702 data sheet).

Texas Instruments LinCMOS process offers

superior analog performance to standard CMOS

processes. Along with the standard CMOS

advantages of low power without sacrificing

speed, high input impedance, and low bias

currents, the LinCMOS process offers ex-

tremely stable input offset voltages, even with

differential input stresses of several volts. This

characteristic makes it possible to build reliable

CMOS comparators.

The TLC393C is characterized for operation over the commercial temperature range of T

= 0°C to 70°C. The

TLC393I is characterized for operation over the extended industrial temperature range of T

= −40°C to 85°C.

The TLC393Q is characterized for operation over the full automotive temperature range of T

= −40°C to 125°C.

The TLC193M and TLC393M are characterized for operation over the full military temperature range of

= −55°C to 125°C.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

        

         

       

   

3 2 1 20 19

910111213

2OUT

2IN−

1IN−

1IN+

1OUT

2IN+

GND

D, JG, P, OR PW PACKAGE

(TOP VIEW)

1OUT

1IN−

1IN+

GND

2OUT

2IN−

2IN+

NC − No internal connection

OUT

symbol (each comparator)

IN+

IN−

FK PACKAGE

(TOP VIEW)

LinCMOS is a trademark of Texas Instruments Incorporated. All other trademarks are the property of their respective owners.

Summary of content (31 pages)

PAGE 1
 SLCS115E − DECEMBER 1986 − REVISED JULY 2003 D Very Low Power . . . 110 µW Typ at 5 V D Fast Response Time . . . tPLH = 2.
PAGE 2
 SLCS115D − DECEMBER 1986 − REVISED JULY 2003 AVAILABLE OPTIONS PACKAGES TA VIOmax at 25°C 0°C to 70°C SMALL OUTLINE (D) CHIP CARRIER (FK) CERAMIC DIP (JG) PLASTIC DIP (P) TSSOP (PW) 5 mV TLC393CD — — TLC393CP TLC393CPWLE − 40°C to 85°C 5 mV TLC393ID — — TLC393IP TLC393IPWLE − 40°C to 125°C 5 mV TLC393QD — — — — − 55°C to 125°C 5 mV TLC393MD TLC193MFK TLC193MJG TLC393MP — The D package is available taped and reeled.
PAGE 3
 SLCS115E − DECEMBER 1986 − REVISED JULY 2003 recommended operating conditions TLC393C Supply voltage, VDD Common-mode input voltage, VIC MIN NOM 3 5 −0.2 Low-level output current, IOL Operating free-air temperature, TA UNIT MAX 16 V VDD − 1.
PAGE 4
 SLCS115D − DECEMBER 1986 − REVISED JULY 2003 recommended operating conditions TLC393I Supply voltage, VDD Common-mode input voltage, VIC MIN NOM 3 5 16 V − 0.2 VDD − 1.
PAGE 5
 SLCS115E − DECEMBER 1986 − REVISED JULY 2003 recommended operating conditions TLC393Q MIN NOM Supply voltage, VDD 4 5 Common-mode input voltage, VIC 0 Low-level output current, IOL Operating free-air temperature, TA UNIT MAX 16 V VDD − 1.
PAGE 6
 SLCS115D − DECEMBER 1986 − REVISED JULY 2003 recommended operating conditions TLC193M, TLC393M MIN NOM Supply voltage, VDD 4 5 Common-mode input voltage, VIC 0 Low-level output current, IOL Operating free-air temperature, TA UNIT MAX 16 V VDD − 1.
PAGE 7
 SLCS115E − DECEMBER 1986 − REVISED JULY 2003 switching characteristics, VDD = 5 V, TA = 25°C (see Figure 3) PARAMETER TEST CONDITIONS TLC393C, TLC393I TLC393Q, TLC193M, TLC393M MIN tPLH tPHL tf f = 10 kH kHz, CL = 15 pF Propagation Pro agation delay time, low low-to-high-level to high level out output ut Fall time, output 4.5 Overdrive = 5 mV 2.5 Overdrive = 10 mV 1.7 Overdrive = 20 mV 1.2 Overdrive = 40 mV 1.1 VI = 1.
PAGE 8
 SLCS115D − DECEMBER 1986 − REVISED JULY 2003 PARAMETER MEASUREMENT INFORMATION A close approximation of the input offset voltage can be obtained by using a binary search method to vary the differential input voltage while monitoring the output state. When the applied input voltage differential is equal, but opposite in polarity, to the input offset voltage, the output changes states.
PAGE 9
 SLCS115E − DECEMBER 1986 − REVISED JULY 2003 PARAMETER MEASUREMENT INFORMATION Propagation delay time is defined as the interval between the application of an input step function and the instant when the output reaches 50% of its maximum value.
PAGE 10
 SLCS115D − DECEMBER 1986 − REVISED JULY 2003 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO IIB Input offset voltage Distribution 4 Input bias current vs Free-air temperature 5 CMRR Common-mode rejection ratio vs Free-air temperature 6 kSVR Supply-voltage rejection ratio vs Free-air temperature 7 VOL Lo le el o Low-level output tp t voltage oltage vs Low-level Low level output out ut current vs Free-air temperature 8 9 IOH Lo le
PAGE 11
 SLCS115E − DECEMBER 1986 − REVISED JULY 2003 TYPICAL CHARACTERISTICS† SUPPLY VOLTAGE REJECTION RATIO vs FREE-AIR TEMPERATURE COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE 90 89 kSVR − Supply Voltage Rejection Ratio − dB 90 VDD = 5 V CMRR − Common-Mode Rejection Ratio − dB 88 87 86 85 84 83 82 81 80 −75 −50 −25 0 25 50 75 100 89 88 87 86 85 84 83 82 81 80 −75 125 VDD = 5 V to 10 V −50 −25 25 50 75 100 125 TA − Free-Air Temp
PAGE 12
 SLCS115D − DECEMBER 1986 − REVISED JULY 2003 TYPICAL CHARACTERISTICS† HIGH-LEVEL OUTPUT CURRENT vs FREE-AIR TEMPERATURE HIGH-LEVEL OUTPUT CURRENT vs HIGH-LEVEL OUTPUT VOLTAGE 1000 I OH − High-Level Output Current − nA I OH − High-Level Output Current − nA 1000 TA = 125°C 100 TA = 85°C TA = 70°C 10 TA = 25°C 1 VDD = VOH = 5 V 100 10 1 VOH = VDD 0.1 25 0.
PAGE 13
 SLCS115E − DECEMBER 1986 − REVISED JULY 2003 TYPICAL CHARACTERISTICS LOW-TO-HIGH-LEVEL OUTPUT RESPONSE TIME vs SUPPLY VOLTAGE HIGH-TO-LOW-LEVEL OUTPUT RESPONSE TIME vs SUPPLY VOLTAGE 5 CL = 15 pF RL = 5.1 kΩ (pullup to VDD) TA = 25°C 5 CL = 15 pF RL = 5.1 kΩ (pullup to VDD) TA = 25°C 4.
PAGE 14
 SLCS115D − DECEMBER 1986 − REVISED JULY 2003 TYPICAL CHARACTERISTICS OUTPUT FALL TIME vs SUPPLY VOLTAGE 60 50 CL = 100 pF t f − Fall Time −ns 40 50 pF 30 15 pF 20 50-mV Overdrive RL = 5.
PAGE 15
 SLCS115E − DECEMBER 1986 − REVISED JULY 2003 APPLICATION INFORMATION 12 V 12 V SN75603 Half-H Driver DIR 5V EN C2 (see Note A) 5.1 kΩ + 5.1 kΩ 100 kΩ + 10 kΩ 5V − 10 kΩ 1/2 TLC393 Motor C1 0.01 µF (see Note B) − 1/2 TLC393 12 V DIR SN75604 Half-H Driver 10 kΩ 5V 10 kΩ Motor Speed Control Potentiometer EN 5V Direction Control S1 SPDT NOTES: A. The recommended minimum capacitance is 10 µF to eliminate common ground switching noise.
PAGE 16
 SLCS115D − DECEMBER 1986 − REVISED JULY 2003 APPLICATION INFORMATION 5V 12 V VCC 12-V Sense 3.3 kΩ RESIN − 5V 10 kΩ 5.1 kΩ + 1 kΩ SENSE TL7705A RESET To µP Reset 1/2 TLC393 REF CT GND 2.5 V 12 V 1 µF CT (see Note B) 5.1 kΩ + VUNREG (see Note A) To µP Interrupt Early Power Fail R1 − 1/2 TLC393 R2 Monitors 5-VDC Rail Monitors 12-VDC Rail Early Power Fail Warning (R1 +R2) R2 B. The value of CT determines the time delay of reset.
PAGE 17
 SLCS115E − DECEMBER 1986 − REVISED JULY 2003 APPLICATION INFORMATION 12 V 12 V R1 100 Ω (see Note B) R2 5 kΩ (see Note C) 5.1 kΩ − 5.1 kΩ − 12 V 1OUT + 1/2 TLC393 12 V 100 kΩ + 1/2 TLC393 100 kΩ 22 kΩ 5.1 kΩ C1 0.01 µF (see Note A) − 2OUT 100 kΩ + 1/2 TLC393 R3 100 kΩ (see Note B) 12 V 1OUT 2OUT NOTES: A. Adjust C1 for a change in oscillator frequency where: 1/f = 1.85(100 kΩ)C1 B. Adjust R1 and R3 to change duty cycle C.
PAGE 18
PACKAGE OPTION ADDENDUM www.ti.
PAGE 19
PACKAGE OPTION ADDENDUM www.ti.
PAGE 20
PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
PAGE 21
PACKAGE MATERIALS INFORMATION www.ti.com 8-Jul-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing 5962-9555101NXDR SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) 8.0 12.0 Q1 D 8 2500 330.0 12.4 6.4 5.2 2.1 W Pin1 (mm) Quadrant TLC393CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLC393CPSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.
PAGE 22
PACKAGE MATERIALS INFORMATION www.ti.com 8-Jul-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) 5962-9555101NXDR SOIC D 8 2500 367.0 367.0 35.0 TLC393CDR SOIC D 8 2500 340.5 338.1 20.6 TLC393CPSR SO PS 8 2000 367.0 367.0 38.0 TLC393CPWR TSSOP PW 8 2000 367.0 367.0 35.0 TLC393IDR SOIC D 8 2500 340.5 338.1 20.6 TLC393IPWR TSSOP PW 8 2000 367.0 367.0 35.0 TLC393QDR SOIC D 8 2500 367.
PAGE 23
MECHANICAL DATA MCER001A – JANUARY 1995 – REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0°–15° 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters).
PAGE 24
PAGE 25
PAGE 26
PAGE 27
PAGE 28
PAGE 29
PAGE 30
PAGE 31
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.