TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 D Low Power Consumption D Wide Common-Mode and Differential Voltage Ranges D Low Input Bias and Offset Currents D Output Short-Circuit Protection D Low Total Harmonic Distortion . . . 0.003% Typ D Low Noise D D D D D Vn = 18 nV/√Hz Typ at f = 1 kHz High Input Impedance . . .
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 description/ordering information (continued) ORDERING INFORMATION TA VIOmax AT 25°C TL071CP TL071CP Tube of 50 TL072CP TL072CP Tube of 25 TL074CN TL074CN Tube of 75 TL071CD Reel of 2500 TL071CDR Tube of 75 TL072CD Reel of 2500 TL072CDR Tube of 50 TL074CD Reel of 2500 TL074CDR Reel of 2000 TL074CNSR TL074 Reel of 2000 TL071CPS
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 description/ordering information (continued) ORDERING INFORMATION TA VIOmax AT 25°C TL071IP TL071IP Tube of 50 TL072IP TL072IP Tube of 25 TL074IN TL074IN Tube of 75 TL071ID Reel of 2500 TL071IDR Tube of 75 TL072ID Reel of 2500 TL072IDR Tube of 50 TL074ID Reel of 2500 TL074IDR CDIP (JG) Tube of 50 TL072MJGB TL072MJGB CFP (U)
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 TL071, TL071A, TL071B D, P, OR PS PACKAGE (TOP VIEW) OFFSET N1 IN− IN+ VCC− 1 8 2 7 3 6 4 5 TL072, TL072A, TL072B D, JG, P, PS, OR PW PACKAGE (TOP VIEW) NC VCC+ OUT OFFSET N2 1OUT 1IN− 1IN+ VCC− 1 8 2 7 3 6 4 5 TL074A, TL074B D, J, N, NS, OR PW PACKAGE TL074 . . .
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 schematic (each amplifier) VCC+ IN+ 64 Ω IN− 128 Ω OUT 64 Ω C1 18 pF ÎÎÎ ÁÁÁ ÁÁÁ 1080 Ω 1080 Ω ÁÁÁÁÁ ÁÁÁÁÁ VCC− OFFSET N1 OFFSET N2 TL071 Only All component values shown are nominal.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage (see Note 1): VCC+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V VCC− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
electrical characteristics, VCC± = ±15 V (unless otherwise noted) PARAMETER TEST CONDITIONS† TL071C TL072C TL074C TA‡ MIN VIO α V IO IIO VO = 0 0, RS = 50 Ω Temperature coefficient of input offset voltage VO = 0, RS = 50 Ω Input offset current VO = 0 Input bias current§ VICR Common-mode Common mode input voltage range VOM Maximum peak output voltage swing TYP MAX 3 10 Full range Full range 18 25°C 5 100 65 200 Full range RL ≥ 10 kΩ 6 MIN TYP MAX 2 3 7.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 electrical characteristics, VCC± = ±15 V (unless otherwise noted) PARAMETER TEST CONDITIONS† TA TL071M TL072M ‡ MIN VIO Input offset voltage VO = 0 0, RS = 50 Ω αV Temperature coefficient of input offset voltage VO = 0, RS = 50 Ω IIO Input offset current VO = 0 IO IIB Input bias current‡ VICR Common-mode input voltage range VOM
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 operating characteristics, VCC± = ±15 V, TA = 25°C TL07xM PARAMETER TEST CONDITIONS SR Slew rate at unity gain VI = 10 V, CL = 100 pF, RL = 2 kΩ, See Figure 1 tr Rise time overshoot Rise-time factor VI = 20 mV, CL = 100 pF, RL = 2 kΩ, See Figure 1 Vn Equivalent input noise voltage RS = 20 Ω In Equivalent input noise current RS = 20 Ω,
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 TYPICAL CHARACTERISTICS Table of Graphs FIGURE IIB Input bias current vs Free-air temperature 4 VOM Maximum output voltage vs Frequency vs Free-air Free air temperature vs Load resistance vs Supply voltage 5, 6, 7 8 9 10 AVD Large signal differential voltage amplification Large-signal vs Free-air Free air temperature vs Frequency 11 12 Pha
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 TYPICAL CHARACTERISTICS† MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY INPUT BIAS CURRENT vs FREE-AIR TEMPERATURE 100 ±15 VOM VOM − Maximum Peak Output Voltage − V IIIB− IB Input Bias Current − nA VCC± = ±15 V 10 1 −50 −25 0 25 50 75 100 VCC± = ±15 V VCC± = ±10 V ±7.5 ÎÎÎÎ VCC± = ±5 V ±5 ±2.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 TYPICAL CHARACTERISTICS† MAXIMUM PEAK OUTPUT VOLTAGE vs LOAD RESISTANCE MAXIMUM PEAK OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE ±15 RL = 10 kΩ ÎÎÎÎ ÎÎÎÎ ±12.5 VOM VOM − Maximum Peak Output Voltage − V VOM − Maximum Peak Output Voltage − V VOM ±15 RL = 2 kΩ ±10 ±7.5 ±5 ÁÁ ÁÁ ±2.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 TYPICAL CHARACTERISTICS† LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY VCC± = ±5 V to ±15 V RL = 2 kΩ TA = 25°C 105 104 0° Differential Voltage Amplification 103 45° 102 Phase Shift AVD A VD − Large-Signal Differential Voltage Amplification 106 90° Phase Shift 101 135° 1 10 1 100 1k 10 k 100 k f − Frequen
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 TYPICAL CHARACTERISTICS† SUPPLY CURRENT PER AMPLIFIER vs SUPPLY VOLTAGE COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE 2 VCC± = ±15 V ICC − Supply Current Per Amplifier − mA I CC± CMRR − Common-Mode Rejection Ratio − dB 89 RL = 10 kΩ 88 87 86 85 83 −75 1.6 1.4 1.2 1 0.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 TYPICAL CHARACTERISTICS NORMALIZED SLEW RATE vs FREE-AIR TEMPERATURE ÁÁÁ ÁÁÁ ÁÁÁ ÁÁÁ Vn V nV/ Hz n − Equivalent Input Noise Voltage − nV/Hz Normalized Slew Rate − V/μ s 1.15 VCC± = ±15 V RL = 2 kΩ CL = 100 pF 1.10 1.05 1 0.95 0.90 0.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs ELAPSED TIME 28 24 VO V O − Output Voltage − mV Overshoot 20 90% 16 12 ÁÁÁ ÁÁÁ 8 4 VCC± = ±15 V RL = 2 kΩ TA = 25°C 10% 0 tr −4 0 0.1 0.2 0.3 0.4 0.5 t − Elapsed Time − μs 0.6 Figure 22 16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 0.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 APPLICATION INFORMATION Table of Application Diagrams PART NUMBER FIGURE 0.5-Hz square-wave oscillator TL071 23 High-Q notch filter TL071 24 Audio-distribution amplifier TL074 25 100-kHz quadrature oscillator TL072 26 AC amplifier TL071 27 APPLICATION DIAGRAM RF = 100 kΩ VCC+ − Output − TL071 CF = 3.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080J − SEPTEMBER 1978 − REVISED MARCH 2005 APPLICATION INFORMATION 1N4148 6 sin ωt 18 kΩ (see Note A) −15 V 18 pF 18 pF 1 kΩ VCC+ VCC+ − 88.4 kΩ TL072 − + 6 cos ωt TL072 + 88.4 kΩ VCC− 1 kΩ 18 pF VCC− 15 V 1N4148 18 kΩ (see Note A) 88.4 kΩ NOTE A: These resistor values may be adjusted for a symmetrical output. Figure 26. 100-kHz Quadrature Oscillator VCC+ 0.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.com 18-Oct-2013 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty TL074MWB ACTIVE CFP W 14 TL081-W ACTIVE WAFERSALE YS 0 1 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) TBD A42 N / A for Pkg Type TBD Call TI Call TI Op Temp (°C) Device Marking (4/5) -55 to 125 8102306DA TL074MWB (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TL071ACDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL071BCDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL071CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL071CDR SOIC D 8 2500 330.0 12.
PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TL071ACDR SOIC D 8 2500 340.5 338.1 20.6 TL071BCDR SOIC D 8 2500 340.5 338.1 20.6 TL071CDR SOIC D 8 2500 340.5 338.1 20.6 TL071CDR SOIC D 8 2500 367.0 367.0 35.0 TL071CPSR SO PS 8 2000 367.0 367.0 38.0 TL071IDR SOIC D 8 2500 340.5 338.1 20.6 TL072ACDR SOIC D 8 2500 340.5 338.1 20.
MECHANICAL DATA MCER001A – JANUARY 1995 – REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0°–15° 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters).
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.