Datasheet
Table Of Contents
- FEATURES
- APPLICATIONS
- DESCRIPTION
- DEVICE INFORMATION
- ABSOLUTE MAXIMUM RATINGS
- THERMAL INFORMATION
- RECOMMENDED OPERATING CONDITIONS
- PWM OPERATION AT RECOMMENDED OPERATING CONDITIONS
- PLL INPUT PARAMETERS AND EXTERNAL FILTER COMPONENTS
- ELECTRICAL CHARACTERISTICS
- DC Characteristics
- AC Characteristics (BTL)
- SERIAL AUDIO PORTS SLAVE MODE
- I2C SERIAL CONTROL PORT OPERATION
- RESET TIMING (RESET)
- TYPICAL CHARACTERISTICS, BTL CONFIGURATION
- TYPICAL CHARACTERISTICS, SE CONFIGURATION
- TYPICAL CHARACTERISTICS, PBTL CONFIGURATION
- DETAILED DESCRIPTION
- POWER SUPPLY
- ERROR REPORTING
- DEVICE PROTECTION SYSTEM
- SSTIMER FUNCTIONALITY
- CLOCK, AUTO DETECTION, AND PLL
- SERIAL DATA INTERFACE
- PWM Section
- SERIAL INTERFACE CONTROL AND TIMING
- I2C SERIAL CONTROL INTERFACE
- Output Mode and MUX Selection
- 2.1-Mode Support
- Single-Filter PBTL-Mode Support
- Dynamic Range Control (DRC)
- BANK SWITCHING
- 26-Bit 3.23 Number Format
- Recommended Use Model
- CLOCK CONTROL REGISTER (0x00)
- DEVICE ID REGISTER (0x01)
- ERROR STATUS REGISTER (0x02)
- SYSTEM CONTROL REGISTER 1 (0x03)
- SERIAL DATA INTERFACE REGISTER (0x04)
- SYSTEM CONTROL REGISTER 2 (0x05)
- SOFT MUTE REGISTER (0x06)
- VOLUME REGISTERS (0x07, 0x08, 0x09, 0x0A)
- VOLUME CONFIGURATION REGISTER (0x0E)
- MODULATION LIMIT REGISTER (0x10)
- INTERCHANNEL DELAY REGISTERS (0x11, 0x12, 0x13, and 0x14)
- PWM SHUTDOWN GROUP REGISTER (0x19)
- START/STOP PERIOD REGISTER (0x1A)
- OSCILLATOR TRIM REGISTER (0x1B)
- BKND_ERR REGISTER (0x1C)
- INPUT MULTIPLEXER REGISTER (0x20)
- CHANNEL 4 SOURCE SELECT REGISTER (0x21)
- PWM OUTPUT MUX REGISTER (0x25)
- DRC CONTROL (0x46)
- BANK SWITCH AND EQ CONTROL (0x50)
- Revision History
TAS5711
SLOS600A –DECEMBER 2009–REVISED AUGUST 2010
www.ti.com
BANK SWITCH AND EQ CONTROL (0x50)
Table 24. Bank Switching Command
D31 D30 D29 D28 D27 D26 D25 D24 FUNCTION
0 – – – – – – – 32 kHz, does not use bank 3
(1)
1 – – – – – – – 32 kHz, uses bank 3
– 0 – – – – – – Reserved
(1)
– – 0 – – – – – Reserved
(1)
– – – 0 – – – – 44.1/48 kHz, does not use bank 3
(1)
– – – 1 – – – – 44.1/48 kHz, uses bank 3
– – – – 0 – – – 16 kHz, does not use bank 3
– – – – 1 – – – 16 kHz, uses bank 3
(1)
– – – – – 0 – – 22.025/24 kHz, does not use bank 3
– – – – – 1 – – 22.025/24 kHz, uses bank 3
(1)
– – – – – – 0 – 8 kHz, does not use bank 3
– – – – – – 1 – 8 kHz, uses bank 3
(1)
– – – – – – – 0 11.025 kHz/12, does not use bank 3
– – – – – – – 1 11.025/12 kHz, uses bank 3
(1)
D23 D22 D21 D20 D19 D18 D17 D16 FUNCTION
0 – – – – – – – 32 kHz, does not use bank 2
(1)
1 – – – – – – – 32 kHz, uses bank 2
– 1 – – – – – – Reserved
(1)
– – 1 – – – – – Reserved
(1)
– – – 0 – – – – 44.1/48 kHz, does not use bank 2
– – – 1 – – – – 44.1/48 kHz, uses bank 2
(1)
– – – – 0 – – – 16 kHz, does not use bank 2
(1)
– – – – 1 – – – 16 kHz, uses bank 2
– – – – – 0 – – 22.025/24 kHz, does not use bank 2
(1)
– – – – – 1 – – 22.025/24 kHz, uses bank 2
– – – – – – 0 – 8 kHz, does not use bank 2
(1)
– – – – – – 1 – 8 kHz, uses bank 2
– – – – – – – 0 11.025/12 kHz, does not use bank 2
(1)
– – – – – – – 1 11.025/12 kHz, uses bank 2
D15 D14 D13 D12 D11 D10 D9 D8 FUNCTION
0 – – – – – – – 32 kHz, does not use bank 1
1 – – – – – – – 32 kHz, uses bank 1
(1)
– 0 – – – – – – Reserved
(1)
– – 0 – – – – – Reserved
(1)
– – – 0 – – – – 44.1/48 kHz, does not use bank 1
(1)
– – – 1 – – – – 44.1/48 kHz, uses bank 1
– – – – 0 – – – 16 kHz, does not use bank 1
(1)
– – – – 1 – – – 16 kHz, uses bank 1
– – – – – 0 – – 22.025/24 kHz, does not use bank 1
(1)
– – – – – 1 – – 22.025/24 kHz, uses bank 1
– – – – – – 0 – 8 kHz, does not use bank 1
(1)
– – – – – – 1 – 8 kHz, uses bank 1
– – – – – – – 0 11.025/12 kHz, does not use bank 1
(1)
– – – – – – – 1 11.025/12 kHz, uses bank 1
(1) Default values are in bold.
58 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): TAS5711