Datasheet

POWER DISSIPATION RATINGS
ABSOLUTE MAXIMUM RATINGS
(1) (2)
RECOMMENDED OPERATING CONDITIONS
SN65HVD233
SN65HVD234
SN65HVD235
www.ti.com .............................................................................................................................................. SLLS557F – NOVEMBER 2002 – REVISED AUGUST 2008
CIRCUIT T
A
≤ 25 ° C DERATING FACTOR
(1)
T
A
= 85 ° C T
A
= 125 ° C
PACKAGE
BOARD POWER RATING ABOVE T
A
= 25 ° C POWER RATING POWER RATING
D Low-K 596.6 mW 5.7 mW/ ° C 255.7 mW 28.4 mW
D High-K 1076.9 mW 10.3 mW/ ° C 461.5 mW 51.3 mW
(1) This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow.
over operating free-air temperature range unless otherwise noted
Value UNIT
V
CC
Supply voltage range – 0.3 to 7 V
Voltage range at any bus terminal (CANH or CANL) – 36 to 36 V
Voltage input range, transient pulse, CANH and CANL, through 100 Ω (see Figure 7 ) – 100 to 100 V
V
I
Input voltage range, (D, R, R
S
, EN, LBK, AB) – 0.5 to 7 V
I
O
Receiver output current – 10 to 10 mA
Electrostatic discharge Human Body Model
(3)
CANH, CANL and GND 16 kV
Human Body Model
(3)
All pins 3 kV
Electrostatic discharge
Charged-Device Mode
(4)
All pins 1 kV
See Dissipation Rating
Continuous total power dissipation
Table
T
J
Operating junction temperature 150 ° C
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, except differential I/O bus voltages, are with respect to network ground terminal.
(3) Tested in accordance with JEDEC Standard 22, Test Method A114-A.
(4) Tested in accordance with JEDEC Standard 22, Test Method C101.
MIN TYP MAX UNIT
V
CC
Supply voltage 3 3.6
Voltage at any bus terminal (separately or common mode) – 7 12
V
IH
High-level input voltage D, EN, AB, LBK 2 5.5 V
V
IL
Low-level input voltage D, EN, AB, LBK 0 0.8
V
ID
Differential input voltage – 6 6
Resistance from R
S
to ground 0 100 k Ω
V
I(Rs)
Input Voltage at R
S
for standby 0.75 V
CC
5.5 V
Driver – 50
I
OH
High-level output current mA
Receiver – 10
Driver 50
I
OL
Low-level output current mA
Receiver 10
T
J
Operating junction temperature HVD233, HVD234, HVD235 150 ° C
T
A
Operating free-air temperature
(1)
HVD233, HVD234, HVD235 -40 125 ° C
(1) Maximum free-air temperature operation is allowed as long as the device maximum junction temperature is not exceeded.
Copyright © 2002 – 2008, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): SN65HVD233 SN65HVD234 SN65HVD235