Datasheet

MSP430F5529, MSP430F5528, MSP430F5527, MSP430F5526
MSP430F5525, MSP430F5524, MSP430F5522, MSP430F5521
MSP430F5519, MSP430F5517, MSP430F5515, MSP430F5514, MSP430F5513
www.ti.com SLAS590L –MARCH 2009–REVISED MAY 2013
Outputs – General Purpose I/O (Reduced Drive Strength)
(P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.7, P4.0 to P4.7)
(P5.0 to P5.7, P6.0 to P6.7, P7.0 to P7.7, P8.0 to P8.2, PJ.0 to PJ.3)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
(1)
PARAMETER TEST CONDITIONS V
CC
MIN MAX UNIT
I
(OHmax)
= –1 mA
(2)
V
CC
– 0.25 V
CC
1.8 V
I
(OHmax)
= –3 mA
(3)
V
CC
– 0.60 V
CC
V
OH
High-level output voltage V
I
(OHmax)
= –2 mA
(2)
V
CC
– 0.25 V
CC
3.0 V
I
(OHmax)
= –6 mA
(3)
V
CC
– 0.60 V
CC
I
(OLmax)
= 1 mA
(2)
V
SS
V
SS
+ 0.25
1.8 V
I
(OLmax)
= 3 mA
(3)
V
SS
V
SS
+ 0.60
V
OL
Low-level output voltage V
I
(OLmax)
= 2 mA
(2)
V
SS
V
SS
+ 0.25
3.0 V
I
(OLmax)
= 6 mA
(3)
V
SS
V
SS
+ 0.60
(1) Selecting reduced drive strength may reduce EMI.
(2) The maximum total current, I
(OHmax)
and I
(OLmax)
, for all outputs combined, should not exceed ±48 mA to hold the maximum voltage drop
specified.
(3) The maximum total current, I
(OHmax)
and I
(OLmax)
, for all outputs combined, should not exceed ±100 mA to hold the maximum voltage
drop specified.
Output Frequency – General Purpose I/O
(P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.7, P4.0 to P4.7)
(P5.0 to P5.7, P6.0 to P6.7, P7.0 to P7.7, P8.0 to P8.2, PJ.0 to PJ.3)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN MAX UNIT
V
CC
= 1.8 V,
16
PMMCOREVx = 0
Port output frequency
f
Px.y
See
(1)(2)
MHz
(with load)
V
CC
= 3 V,
25
PMMCOREVx = 3
V
CC
= 1.8 V,
ACLK,
16
PMMCOREVx = 0
SMCLK,
f
Port_CLK
Clock output frequency MHz
MCLK,
V
CC
= 3 V,
25
C
L
= 20 pF
(2)
PMMCOREVx = 3
(1) A resistive divider with 2 × R1 between V
CC
and V
SS
is used as load. The output is connected to the center tap of the divider. For full
drive strength, R1 = 550 Ω. For reduced drive strength, R1 = 1.6 kΩ. C
L
= 20 pF is connected to the output to V
SS
.
(2) The output voltage reaches at least 10% and 90% V
CC
at the specified toggle frequency.
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 55
Product Folder Links: MSP430F5529 MSP430F5528 MSP430F5527 MSP430F5526 MSP430F5525 MSP430F5524
MSP430F5522 MSP430F5521 MSP430F5519 MSP430F5517 MSP430F5515 MSP430F5514 MSP430F5513