Datasheet

LM4050-N, LM4050-N-Q1
www.ti.com SNOS455E –MAY 2000–REVISED APRIL 2013
LM4050-N-8.2
Electrical Characteristics
Boldface limits apply for T
A
= T
J
= T
MIN
to T
MAX
; all other limits T
A
= T
J
= 25°C. The grades A, B and C designate initial
Reverse Breakdown Voltage tolerances of ±0.1% and ±0.2% and 0.5% respectively.
LM4050- LM4050- LM4050-
NAIM3 NBIM3 NCIM3
Units
Symbol Parameter Conditions Typical
(1)
LM4050- LM4050- LM4050-
(Limit)
NAEM3 NBEM3 NCEM3
Limits
(2)
Limits
(2)
Limits
(2)
V
R
Reverse Breakdown Voltage I
R
= 150 μA 8.192 V
Reverse Breakdown Voltage I
R
= 150 μA ±8.2 ±16 ±41 mV (max)
Tolerance
(3)
Industrial Temp. Range ±35 ±43 ±68 mV (max)
Extended Temp. Range ±49 ±57 ±82 mV (max)
I
RMIN
Minimum Operating Current 74 μA
91 91 91 μA (max)
Industrial Temp. Range 95 95 95 μA (max)
Extended Temp. Range 100 100 100 μA (max)
ΔV
R
/ΔT Average Reverse Breakdown I
R
= 10 mA ±40 ppm/°C
Voltage Temperature Coefficient
(3)
I
R
= 1 mA ±20 ppm/°C
I
R
= 150 μA ±20 ±50 ±50 ±50 ppm/°C (max)
ΔV
R
/ΔI
R
Reverse Breakdown Voltage I
RMIN
≤ I
R
≤ 1 mA 0.6 mV
Change with Operating Current
1.3 1.3 1.3 mV (max)
Change
(4)
2.5 2.5 2.5 mV (max)
1 mA ≤ I
R
≤ 15 mA 7.0 mV
10.0 10.0 10.0 mV (max)
18.0 18.0 18.0 mV (max)
Z
R
Reverse Dynamic Impedance I
R
= 1 mA, f = 120 Hz, 0.6
Ω
I
AC
= 0.1 I
R
e
N
Wideband Noise I
R
= 150 μA 150
μV
rms
10 Hz ≤ f ≤ 10 kHz
ΔV
R
Reverse Breakdown Voltage Long t = 1000 hrs 120
Term Stability T = 25°C ±0.1°C ppm
I
R
= 150 μA
V
HYST
Thermal Hysteresis ΔT = −40°C to 125°C 2.3
mV
(5)
(1) Typicals are at T
J
= 25°C and represent most likely parametric norm.
(2) Limits are 100% production tested at 25°C. Limits over temperature are guaranteed through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate National's AOQL.
(3) The boldface (over-temperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse
Breakdown Voltage Tolerance ±[(ΔV
R
/ΔT)(maxΔT)(V
R
)]. Where, ΔV
R
/ΔT is the V
R
temperature coefficient, maxΔT is the maximum
difference in temperature from the reference point of 25°C to T
MIN
or T
MAX
, and V
R
is the reverse breakdown voltage. The total over-
temperature tolerance for the different grades in the industrial temperature range where maxΔT = 65°C is shown below: A-grade:
±0.425% = ±0.1% ±50 ppm/°C × 65°C B-grade: ±0.525% = ±0.2% ±50 ppm/°C × 65°C C-grade: ±0.825% = ±0.5% ±50 ppm/°C ×
65°CTherefore, as an example, the A-grade LM4050-N-2.5 has an over-temperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.425% = ±11 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature +125°C.
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM4050-N LM4050-N-Q1