Datasheet
LM4040-N, LM4040Q-N
www.ti.com
SNOS633H –OCTOBER 2000–REVISED APRIL 2013
2.5-V LM4040-N Electrical Characteristics
V
R
Tolerance Grades 'C', 'D', and 'E'; Temperature Grade 'I' (AEC Grade 3)
Boldface limits apply for T
A
= T
J
= T
MIN
to T
MAX
; all other limits T
A
= T
J
= 25°C. The grades C, D and E designate initial
Reverse Breakdown Voltage tolerances of ±0.5%, ±1.0% and ±2.0%, respectively.
LM4040CIZ LM4040DIZ LM4040EIZ
LM4040CIM3 LM4040DIM3 LM4040EIM3
Symbol Parameter Conditions Typical
(1)
LM4040CIM7 LM4040DIM7 LM4040EIM7 Units
LM4040QCIM3 LM4040QDIM3 LM4040QEIM3
Limits
(2)
Limits
(2)
Limits
(2)
Reverse Breakdown
I
R
= 100 μA 2.500 V
Voltage
V
R
±12 ±25 ±50 mV (max)
Reverse Breakdown
I
R
= 100 μA
Voltage Tolerance
(3)
±29 ±49 ±74 mV (max)
45 μA
Minimum Operating
I
RMIN
60 65 65 μA (max)
Current
65 70 70 μA (max)
Average Reverse I
R
= 10 mA ±20 ppm/°C
Breakdown Voltage
I
R
= 1 mA ±15 ±100 ±150 ±150 ppm/°C (max)
ΔV
R
/ΔT
Temperature
I
R
= 100 μA ±15 ppm/°C
Coefficient
(3)
0.3 mV
I
RMIN
≤ I
R
≤ 1 mA 0.8 1.0 1.0 mV (max)
Reverse Breakdown
1.0 1.2 1.2 mV (max)
Voltage Change with
ΔV
R
/ΔI
R
Operating Current
2.5 mV
Change
(4)
1 mA ≤ I
R
≤ 15 mA 6.0 8.0 8.0 mV (max)
8.0 10.0 10.0 mV (max)
0.3 Ω
Reverse Dynamic I
R
= 1 mA, f = 120 Hz
Z
R
Impedance I
AC
= 0.1 I
R
0.9 1.1 1.1 Ω(max)
I
R
= 100 μA
e
N
Wideband Noise 35 μV
rms
10 Hz ≤ f ≤ 10 kHz
Reverse Breakdown t = 1000 hrs
ΔV
R
Voltage Long Term T = 25°C ±0.1°C 120 ppm
Stability I
R
= 100 μA
V
HYST
Thermal Hysteresis
(5)
ΔT= −40°C to +125°C 0.08 %
(1) Typicals are at T
J
= 25°C and represent most likely parametric norm.
(2) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(3) The boldface (over-temperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse
Breakdown Voltage Tolerance ±[(ΔV
R
/ΔT)(maxΔT)(V
R
)]. Where, ΔV
R
/ΔT is the V
R
temperature coefficient, maxΔT is the maximum
difference in temperature from the reference point of 25°C to T
MIN
or T
MAX
, and V
R
is the reverse breakdown voltage. The total over-
temperature tolerance for the different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total over-temperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown
below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an over-temperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature +125°C.
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM4040-N LM4040Q-N