Datasheet

DS26LS32AC, DS26LS32C, DS26LS32M, DS26LS33M
www.ti.com SNLS352C –MAY 1999–REVISED FEBRUARY 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1)(2)
Supply Voltage 7V
Common-Mode Range ±25V
Differential Input Voltage ±25V
Enable Voltage 7V
Output Sink Current 50 mA
Maximum Power Dissipation
(3)
at 25°C
Cavity Package 1433 mW
Molded DIP Package 1362 mW
SOIC Package
(4)
DS26LS32 1002 mW
DS26LS32A 1051 mW
Storage Temperature Range −65°C to +165°C
Lead Temperature (Soldering, 4 seconds) 260°C
(1) “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to
imply that the device should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device
operation.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(3) Derate cavity package 9.6 mW/°C above 25°C; derate molded DIP package 10.9 mW/°C above 25°C.
(4) Derate SOIC Package 8.01 mW/°C for DS26LS32 8.41 mW/°C for DS26LS32A
Operating Conditions
Min Max Units
Supply Voltage, (V
CC
)
DS26LS32M, DS26LS33M (MIL) 4.5 5.5 V
DS26LS32C, DS26LS32AC (COML) 4.75 5.25 V
Temperature, (T
A
)
DS26LS32M, DS26LS33M (MIL) −55 +125 °C
DS26LS32C, DS26LS32AC (COML) 0 +70 °C
Electrical Characteristics
(1) (2) (3)
over the operating temperature range unless otherwise specified
Symbol Parameter Conditions Min Typ Max Units
V
TH
Differential Input Voltage V
OUT
= V
OH
or DS26LS32, DS26LS32A, −7V ≤ V
CM
≤ +7V −0.2 ±0.07 0.2 V
V
OL
DS26LS33, DS26LS33A, −15V ≤ V
CM
+15V −0.5 ±0.14 0.5 V
R
IN
Input Resistance −15V ≤ V
CM
≤ +15V (One Input AC GND) 6.0 8.5 kΩ
I
IN
Input Current (Under V
IN
= 15V, Other Input −15V ≤ V
IN
≤ +15V 2.3 mA
Test)
V
IN
= −15V, Other Input −15V ≤ V
IN
≤ +15V −2.8 mA
V
OH
Output High Voltage V
CC
= MIN, ΔV
IN
= 1V, Commercial 2.7 4.2 V
V
ENABLE
= 0.8V, I
OH
= −440 μA Military 2.5 4.2 V
V
OL
Output Low Voltage V
CC
= Min, ΔV
IN
= −1V, I
OL
= 4 mA 0.4 V
V
ENABLE
= 0.8V I
OL
= 8 mA 0.45 V
V
IL
Enable Low Voltage 0.8 V
V
IH
Enable High Voltage 2.0 V
V
I
Enable Clamp Voltage V
CC
= Min, I
IN
= −18 mA −1.5 V
(1) All currents into device pins are shown as positive, all currents out of device pins are shown as negative, all voltages are referenced to
ground, unless otherwise specified. All values shown as max or min are so classified on absolute value basis.
(2) All typical values are V
CC
= 5V, T
A
= 25°C.
(3) Only one output at a time should be shorted.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: DS26LS32AC DS26LS32C DS26LS32M DS26LS33M