Datasheet
DRV632
SLOS681A –JANUARY 2011–REVISED JULY 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
(1)
T
A
PACKAGE DESCRIPTION
–40°C to 85°C DRV632PW 14-Pin
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
ABSOLUTE MAXIMUM RATINGS
(1)
over operating free-air temperature range
VALUE UNIT
Supply voltage, VDD to GND –0.3 to 4 V
V
I
Input voltage V
SS
– 0.3 to VDD + 0.3 V
R
L
Minimum load impedance – line outputs – OUTL, OUTR 600 Ω
Mute to GND, UVP to GND –0.3 to VDD + 0.3 V
T
J
Maximum operating junction temperature range –40 to 150 °C
T
stg
Storage temperature range –40 to 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
THERMAL INFORMATION
DRV632
THERMAL METRIC
(1)
PW UNIT
14 PINS
θ
JA
Junction-to-ambient thermal resistance
(2)
130 °C/W
θ
JCtop
Junction-to-case (top) thermal resistance
(3)
49 °C/W
θ
JB
Junction-to-board thermal resistance
(4)
63 °C/W
ψ
JT
Junction-to-top characterization parameter
(5)
3.6 °C/W
ψ
JB
Junction-to-board characterization parameter
(6)
62 °C/W
θ
JCbot
Junction-to-case (bottom) thermal resistance
(7)
n/a °C/W
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(2) The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
(3) The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDEC-
standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
(4) The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB
temperature, as described in JESD51-8.
(5) The junction-to-top characterization parameter, ψ
JT
, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θ
JA
, using a procedure described in JESD51-2a (sections 6 and 7).
(6) The junction-to-board characterization parameter, ψ
JB
, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θ
JA
, using a procedure described in JESD51-2a (sections 6 and 7).
(7) The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific
JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
Spacer
2 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DRV632