User's Manual
Table Of Contents
- Table of Contents
- Preface
- 1 eZ430-Chronos™ Overview
- 2 Getting Started
- 3 eZ430-Chronos Software
- 3.1 Overview
- 3.2 eZ430-Chronos Sports Watch Software
- 3.2.1 Detailed Feature Overview - Modes Using the Top LCD Line
- 3.2.1.1 Time Mode
- 3.2.1.2 Alarm Mode
- 3.2.1.3 Temperature Mode
- 3.2.1.4 Altimeter Mode
- 3.2.1.5 Heart Rate Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.1.6 Speed Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.1.7 Tilt Mode
- 3.2.2 Detailed Feature Overview - Modes Using the Bottom LCD Line
- 3.2.2.1 Date Mode
- 3.2.2.2 Stopwatch Mode
- 3.2.2.3 Battery Voltage Mode
- 3.2.2.4 Acceleration Mode - RF
- 3.2.2.5 PowerPoint Mode - RF
- 3.2.2.6 Sync Mode - RF
- 3.2.2.7 Calorie/Distance Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.2.8 Wireless Update - RF
- 3.2.2.9 Chronos-to-Chronos (C2C) Mode
- 3.2.1 Detailed Feature Overview - Modes Using the Top LCD Line
- 3.3 eZ430-Chronos Control Center PC Software
- 3.4 eZ430-Chronos Watch Data Logger
- 3.5 Data Logger PC Software
- 3.6 eZ430-Chronos Software Projects
- 4 eZ430-Chronos Hardware
- 4.1 Programming/Reprogramming the eZ430-Chronos Watch: Disassembly and Assembly of the Housing
- 4.2 Functional Description of the eZ430-Chronos Watch
- 4.3 Functional Description of the eZ430-Chronos RF Access Point
- 4.4 Functional Description of the eZ430-Chronos Debug Interface
- 4.5 Schematics, Layout, BOM, and LCD
- 4.6 Access Point Schematics, Layout and BOM
- A Frequently Asked Questions
- B Detailed Hardware Driver Installation Guide
- Important Notices
Chapter 2
SLAU292D–November 2009–Revised March 2011
Getting Started
2.1 Using the eZ430-Chronos Watch Stand Alone
For first time use, remove the eZ430-Chronos watch from box and press any button twice to wake the
watch from sleep mode (after the first button press, the LCD displays the same content as shown on the
box of the kit; after the second button press, the watch starts full operation).
NOTE: For the next steps it is important to understand the eZ430-Chronos user concept. The top
and bottom LCD lines can be controlled individually by pushing the buttons on the left side.
The buttons on the right side are used to select or activate secondary functions. Detailed
instructions are available in Section 3.2.
Figure 2-2. Overview eZ430-Chronos LCD
Figure 2-1. eZ430-Chronos Watch Push Buttons
2.1.1 Setting the Time
1. Push the "*" button until the time is displayed in the top LCD line.
2. Hold "*" for three seconds until the time disappears and "12H" or "24H" is shown on the LCD.
3. Select 12H/24H modes by pushing the "UP" or "DOWN" buttons.
4. Press "#" to continue with the time adjustment.
5. Set the hours by pushing the "UP" or "DOWN" button.
6. Press "#" to continue with the minute adjustment.
7. Set the minutes by pushing the "UP" or "DOWN" button.
8. Press "#" to continue with the second adjustment.
9. Set the seconds by pushing the "UP" or "DOWN" button.
10. Press "*" to confirm the settings and go back to normal operation, or press "#" to start over with step 2.
10
Getting Started SLAU292D–November 2009–Revised March 2011
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated