User's Manual
Table Of Contents
- Table of Contents
- Preface
- 1 eZ430-Chronos™ Overview
- 2 Getting Started
- 3 eZ430-Chronos Software
- 3.1 Overview
- 3.2 eZ430-Chronos Sports Watch Software
- 3.2.1 Detailed Feature Overview - Modes Using the Top LCD Line
- 3.2.1.1 Time Mode
- 3.2.1.2 Alarm Mode
- 3.2.1.3 Temperature Mode
- 3.2.1.4 Altimeter Mode
- 3.2.1.5 Heart Rate Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.1.6 Speed Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.1.7 Tilt Mode
- 3.2.2 Detailed Feature Overview - Modes Using the Bottom LCD Line
- 3.2.2.1 Date Mode
- 3.2.2.2 Stopwatch Mode
- 3.2.2.3 Battery Voltage Mode
- 3.2.2.4 Acceleration Mode - RF
- 3.2.2.5 PowerPoint Mode - RF
- 3.2.2.6 Sync Mode - RF
- 3.2.2.7 Calorie/Distance Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.2.8 Wireless Update - RF
- 3.2.2.9 Chronos-to-Chronos (C2C) Mode
- 3.2.1 Detailed Feature Overview - Modes Using the Top LCD Line
- 3.3 eZ430-Chronos Control Center PC Software
- 3.4 eZ430-Chronos Watch Data Logger
- 3.5 Data Logger PC Software
- 3.6 eZ430-Chronos Software Projects
- 4 eZ430-Chronos Hardware
- 4.1 Programming/Reprogramming the eZ430-Chronos Watch: Disassembly and Assembly of the Housing
- 4.2 Functional Description of the eZ430-Chronos Watch
- 4.3 Functional Description of the eZ430-Chronos RF Access Point
- 4.4 Functional Description of the eZ430-Chronos Debug Interface
- 4.5 Schematics, Layout, BOM, and LCD
- 4.6 Access Point Schematics, Layout and BOM
- A Frequently Asked Questions
- B Detailed Hardware Driver Installation Guide
- Important Notices
www.ti.com
eZ430-Chronos Sports Watch Software
3.2.2.5 PowerPoint Mode - RF
This mode requires the eZ430-Chronos Control Center PC software.
Press "#" until "PPt" is shown (see Figure 3-1). This mode allows control of a PowerPoint presentation by
translating button pushes on the watch into keystrokes of the PC keyboard. No acceleration or other data
is transmitted. The default settings are:
• "#" - Go to presentation mode (F5)
• "*" - Previous slide (Left)
• "UP" - Next slide (Right)
The Control Center allows user defined key settings (including combinations) - see Section 3.3.2.
Secondary function: Start/stop transmission of button pushes. Pushing "DOWN" starts/stops the pairing
process or stops the transmission (the access point on the PC must be started from the eZ430-Chronos
Control Center (see Section 3.3.1). The RF icon on the LCD flashes when the radio is active; if pairing
fails, the icon disappears. The top LCD line shows the time during the pairing until the data transmission is
disabled.
Set function: None
3.2.2.6 Sync Mode - RF
This mode requires the eZ430-Chronos Control Center PC software.
Press "#" until "SYnC" is shown (see Figure 3-1). This mode allows doing a variety of watch settings
conveniently from the eZ430-Chronos Control Center PC software over the air (see Section 3.3.3).
• Time settings
• Date settings
• Altitude calibration
• Temperature calibration
Secondary function: Start/stop link for Sync Mode. Pushing "DOWN" starts/stops the pairing process or
stop the link (the access point on the PC must be started first from the eZ430-Chronos Control Center
(see Section 3.3.3). The RF icon on the LCD flashes when the radio is active. If the pairing fails, it
disappears. After a successfully received message, the LCD shows "DONE". The top LCD line is off
during the pairing and until the Sync Mode is disabled.
Set function: None
23
SLAU292D–November 2009–Revised March 2011 eZ430-Chronos Software
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated