Technical Specifications

TECHNICAL DATA
TES-40
TESTORS
®
CRAFT
DISTRESSED IVORY KIT
1
Form: ARJ-2079
Rev.: 060120
DESCRIPTION AND USES
Testors
®
Craft Distressed Ivory Kit is designed to add
antique quality to bare wood and previously painted wood,
as well as metal, plaster, masonry and unglazed ceramics. It
is suitable for interior use or for use in a covered outdoor
location. This easy 2-step process does not require priming.
PRODUCT
KIT CONTENTS
Ivory Base Coat (211827 1-Quart)
Antique Top Coat (260508 1-Pint)
Sanding Pad
Gloves
Paint Brush
PRODUCT APPLICATION
PAINTING CONDITIONS
Apply only when the ambient air and surface temperatures
are between 50-90ºF (10-32ºC) and humidity is below 85%
to ensure proper drying.
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants
by washing the surface with soap and water, or other
suitable cleaning method. Rinse with fresh water and allow
to thoroughly dry. Remove loose paint and rust with a wire
brush or sandpaper. Lightly sand previously painted or
glossy surfaces with the enclosed sanding pad to improve
paint adhesion. Wipe with a soft cloth or tack cloth to remove
sanding dust.
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and
a wet mop. Before you start, find out how to protect yourself
and your family by contacting the National Lead Information
Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
PRODUCT APPLICATION (cont.)
BASE COAT APPLICATION
Wear the enclosed gloves. Stir thoroughly to ensure any
settled pigment is re-dispersed. Thinning is not required. In
hot, dry conditions, thin with up to 2 ounces of water per
quart to extend dry time. Avoid painting in direct sunlight or
on hot surfaces. Using the enclosed brush, apply the base
coat using even strokes. For wooden objects, always brush
in the direction of the wood grain. Avoid excessive brushing.
Two coats may be necessary depending on the original color
of the object. Once the base coat is thoroughly dry (2 hours),
the object is ready to distress and apply the antique top coat.
DISTRESSING THE SURFACE
Use the enclosed sanding pad to sand (distress) areas that
would be naturally worn, such as edges, raised areas, and
corners. Always sand in the direction of the grain of the
wood. When sanding is complete, wipe down with a soft
cloth or tack cloth to remove sanding dust. Once you have
completed distressing the object, the object is ready to
applying the antiquing topcoat.
ANTIQUE TOP COAT APPLICATION
Stir gently before and during application. DO NOT SHAKE.
Do not apply below 55°F (13°C). Put on the enclosed gloves.
Using the enclosed brush, apply liberally to the work area no
larger than 2 square feet. Immediately after applying the
stain, wipe with a damp cloth. The stain will stay in the
exposed wood areas. For a heavier or more distressed
effect, wipe the stain immediately with a dry cloth. More stain
can be applied and wiped off to achieve the desired look.
Dries to the touch in 15 minutes.
For extra protection on heavily used surfaces such as table
tops or outdoor objects, top coat Rust-Oleum
®
Imagine
Matte Clear. Allow the object to dry overnight before
applying the Matte Clear.
DRY & RECOAT TIMES
Dry and recoat times are based on 70ºF and 50% relative
humidity. Allow more time at cooler temperatures. The base
coat dries to touch in 30 minutes, and may be recoated in 2-
4 hours. The antique top coat dries to the touch in 15
minutes and is fully dry in 24 hours.
CLEAN-UP
Clean brush and other application tools immediately with
soap and water.