IN STALLATION WARN IN G Please make sure at least 2 people install the trampoline. Please install the trampoline on the flat and non-slippery ground. Please install the springs in the X -shape order one by one as requested in the instructions. Please do not move or lift the trampoline during or after installation but use the tie down stakes kit to secure it.
USE WARN IN G D o not somersault or flip. D o not dunk and hold onto the ring. D o not jump onto the trampoline from a height. D o not intentionally hit the safety enclosure net. 3 5 0 LBS D o not use the trampoline in stormy weather but disassemble and store it. D o not exceed 330lbs for a single user and do not exceed the total weight for multiple users. D o not place any sharp objects on the trampoline. D o not use during pregnancy, high blood pressure or other injuries.
ADDITION AL SAFETY WARN IN G Read all instructions before using the trampoline. U se trampoline only under adult super vision. N ot recommended for children under six years old. Secure the trampoline against unauthorized use. U se only when the jumping mat is clean and dr y. D o not use the trampoline without the spring cover pad. D o not use the trampoline while under the influence of alcohol or drugs. D o not smoke while using the trampoline.
Top Rail T-shaped Connector Leg Extension (two holes) Leg Extension Base Leg Upper pole B Upper pole A Frame Pad Safety Net Net Rope Bolt Pack (M6*75) Spring Jumping Mat
Spring Tool Wrench Soft Backboard Frame Pole Step Pole Bolt Pack (M6*35)
Step 1 Attach the Top Rail (# 1) to the T-shaped Connector (# 2)until you form the circle.As shown in Fig.(You can use great force if it is too tight) Step 2 Insert the Leg Extension (# 3) with the Leg Extension (# 4) into the Base Leg (# 5) and stick out completely,totally 5 legs.As shown in Fig.
Step 3 Two people will be necessary at this point to install the trampoline.One person lifts up the circle frame, while the other lifts the W-shaped leg tubes to a standing position and inserts the T-shaped Connector (#4)into a W-shaped leg tube.Ensure the locking holes are aligned.As shown in Fig. Step 4 Layout the Jumping Mat(#13) inside the circle frame.
Step 5 Install the Springs(#12) in the X-shape order one by one to make sure the tension is distrib uted evenly for the Jumping Mat(#13) and pull it with Spring tool(#14).As shown in Fig.(Tip: Please take care not to pinch your hands and other body parts during spring assembly.
Step 6 Please lay the frame cover pad (#8) over the springs; Tie the strap located at the under side of the frame pad to the frame.As shown in fig. Step 7 The Upper Pole B(#6) is locked and fixed in the two holes at the upper end of Leg Extension (#3) with screw (#11).As shown in fig.
Step 8 Please insert the Upper Pole A (#7) into the Upper Pole B (#6).As shown in fig. Step 9 Spread Safety Net (#9) out on the trampoline mat. Pass the strap through the ring of the Upper Pole Cap (#7), along the Upper Pole Cap (# 7), and through the buckle, and lock the buckle. As shown in fig.
Step 10 Components Net Ropes (#10),Safety Net(#9) through the bottom hole components,and parts cross around spring, and fixed.As shown in fig. Step 11 Fixed the Soft Backboard(#16)on the Safety Net(#9),the upper two bands are fixed on the top of the Upper Pole A (#7), and the bottom two belts are fixed on the Safety Net (#9), As shown in the figure.
Step 12 Take out the Frame Pole(#17),Step Pole(#18) and screw(#19).And screw the Step Pole(#18) above the Frame Pole(#17) as shown in the figure.