Project Name: Document No. Bluetooth AP CPE-U1-1210S-USR02-011N Date Issued: Revision: 08-30-2002 0.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document 1. INTRODUCTION 1.1. The Bluetooth Technology Bluetooth is a worldwide standard for the wireless exchange of data between two compatible devices. It utilities short-distance radio link technology and replaces the traditional cable connections to enable wireless connections between desktop and laptop computers, cellular phones, scanners, digital cameras, printers and other devices.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document 2.3. Bluetooth Clients supported Point-to-multipoint with 1.1 clients supporting: LAN Access Profile (LAP) WEBSITE UPDATES FOR COMPATIBILITY MATRIX??? 2.4. Configuration and Management Local connection, over Bluetooth or Ethernet LAN HTTP-based interface (RFC 2616/2617) DHCP (RFC 2131) Client and Server Static IP addressing 2.5. Bluetooth Radio PARTNERSHIP DEALS 2.6.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document If you do not have a DHCP-enabled network, or you would like to manually set up your Access Point’s network configurations eg. its static IP address, then you can use the Web Interface’s various advanced configuration pages such as Network, Bluetooth and Maintenance. 3.1.1.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document If your PC is in the same network with the Access Point, running the setup-free Locator utility will automatically scan the network and identify your Access Point. It will display the IP address. Figure 2 Locator displaying Bluetooth Access Point To access the Web Interface, you can simply highlight Bluetooth Access Point and hit the web icon on Locator (please refer to the Locator section for more information).
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document Network Settings: Access Point Internet Settings (IP Address, Subnet Mask, Gateway and DNS entries). Figure 3 Information page on the Web Interface Devices page displays information about the Bluetooth clients currently connected to the Access Point. Hit the Refresh button to get the current status of connected Bluetooth clients.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document Figure 4 Devices page on the Web Interface 3.1.3. Network This is an advanced setup page for the Network settings of Bluetooth Access Point. Here you can set the Bluetooth name for your Access Point. The factory default name is Bluetooth AP. By default, the IP Address of Bluetooth Access Point is appended to the Bluetooth name that will appear on Bluetooth clients.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document Figure 5 Network page on the Web Interface 3.1.4. Advanced Setup without DHCP When Bluetooth Access Point is powered up, it automatically looks for a DHCP server in the network to get an IP address for itself so that the Access Point is ready to use without user intervention. However, if there is no DHCP server in the environment, Bluetooth Access Point will reset to its factory default static IP address 192.168.1.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document Figure 6 Configuring the IP Address through Locator Alternatively, you can use the Web Interface to manually set the IP address of the Access Point: 1. Connect your PC to Bluetooth Access Point through a cross-over CAT5 Ethernet cable (or through a hub using normal Ethernet cables) 2.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document You can leave the IP Addresses for Bluetooth clients Automatic even if the IP Address of Bluetooth Access Point is set manually. You may, however, decide to set them manually specifying a starting static IP Address in the same subnet of your Access Point’s IP Address. Warning: If the IP Address of the Access Point is Static (eg. 192.168.1.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document Figure 7 Bluetooth page on the Web Interface 3.1.6. Utilities You can set a new Web Interface password in this page. The default password is admin. You can also restore the Access Point to its factory default settings. Note: The Web Interface logs out the administrator automatically after 10 minutes of inactivity for security purposes.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document Figure 9 Configure on Locator 3. Upgrade N/A 4. Web The basic Web Interface let user can monitor and configure Access Point and all of Bluetooth device information in anywhere. 5. AutoIP N/A 4. Technical Specifications The Ubicom Bluetooth Access Point Reference Design is a complete Bluetooth™ access point with robust networking features required for IP networking over Ethernet. 4.1.1.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document Compliance: • Bluetooth Core Specification 1.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document I cannot access the Internet First, make sure that your Bluetooth client is connected to the Access Point. You should be able to successfully "ping" the Access Point (from a shell or command prompt) at its IP address. Or alternatively, you should be able to connect to the Web Interface. If you cannot successfully "ping" the Access Point, review your client setup manual to determine how to connect properly.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document The LAN Link/Activity LED does not light Make sure the RJ45 cable connection at the side of the Access Point is secure and that the connection to the wall or device (e.g. a hub) is secure, as well. If the LAN Link LED still does not light, make sure the upstream device to which the cable is connected is working properly. If these steps do not work, try using another RJ45 cable as the current cable may be faulty.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document Finally, make sure that the password has not been changed. If you think that the password may have been changed and/or lost, you can restore the Access Point to the factory defaults. How do I restore the factory defaults? Go to the Maintenance page in the Web Interface and follow the instructions to restore the factory default settings. How do I obtain additional support? - Check www.XXX.
TECOM CO., LTD. Prepared by: CPE-U1 TECOM Bluetooth Access Point PROJECT Internal Document Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
