Use and Care Manual

ManualsBrandsTechni Sport ManualsFurniturePink Gaming Chair

PARTS LIST

ATTENTION: Before you begin the assembly,

make sure that all parts are included in good

condition.

ASSEMBLY INSTRUCTIONS FOR TECHNI SPORT CHAIRS

PRO-GAMER MODELS: TS43, TS46, TS48 & TS49

GG SERIES MODELS: TS50, TS51 & TS52

ATTENTION:

⚠ Follow the instructions step by step.

⚠ To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places.

⚠ Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes.

⚠ Using the wrong size of screws on a part could result in damage to the screw or the part.

Backrest, x1

Seat, x1

Hydraulic

Gas Lift, x1

Covers for

Gas Lift, x1 set

Star Base, x1

Caster, x5

Insert the casters (H) into the legs of

the base (G) using pressure.

REMOVE AND DISCARD THE PLASTIC

CAP FROM THE TOP OF THE GAS LIFT

(E), and place the gas lift in the middle of the

base and cover it with (F) as shown.

With the seat positioned as shown,

assemble the armrests (C) to the

seat frame on their respective sides using

screws (I), O’ rings (M) and washers (N).

Assemble the backrest (A) to the

metal brackets on both sides of the

seat (B) using screws (J), o ’rings (M) and

washers (N) as shown.

M8x20mm

+ felt gasket, x4

(Mechanism)

(Armrest, Backrest)

(Brackets Covers)

Tighten the screws well before you sit on the

chair for the first time.

First attach the lumbar pillow (Q),

then the neck pillow (P) by

fastening the buckles behind the

backrest as shown.

Hole covers, x2

Washers, x16

O’ ring, x16

M6x12mm, x2

M8x25mm, x12

Bracket Covers

Attach the covers (K) to the brackets

on their respective sides using

screws (L) and cover the holes with (O).

Then place the seat over the base, making

sure the tip of the gas lift enters into the

hole of the mechanism.

Mechanism,

Right

Neck Pillow, x1

Lumbar Pillow,

Right

Left

Armrests

(Sitting on the chair,

Not looking at it)

Place the seat (B) upside-down with

its back end towards you as shown.

Peel off and place the felt gaskets (I) on the

holes, and then using screws (I), O ’rings

(M) and washers (N), assemble the

mechanism (D) to the seat with its handle

facing to your LEFT.

(LEFT)

(RIGHT)

Left

Allen Wrench, x1

Summary of content (2 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS FOR TECHNI SPORT CHAIRS PRO-GAMER MODELS: TS43, TS46, TS48 & TS49 GG SERIES MODELS: TS50, TS51 & TS52 ATTENTION: PARTS LIST ATTENTION: Before you begin the assembly, make sure that all parts are included in good condition. A Backrest, x1 M8x20mm + felt gasket, x4 I (Mechanism) M8x25mm, x12 J B Insert the casters (H) into the legs of the base (G) using pressure.
PAGE 2
CHAIR’S FUNCTIONS: (1) To raise or lower the chair’s height, pull UP the lever that is under the seat. The chair goes down while sitting on it, or up if you lift your body. (2) To make the chair tilt, pull the same lever OUT horizontally to unlock this function, and IN to lock again. (3) To adjust the tension for the tilting function, turn the mechanism’s knob in either direction to apply more or less tension.