MODEL RTA-2018 ASSEMBLY INSTRUCTIONS ☛ Assembly video also available online at technimobili.com Thank you for purchasing one of our products. Please read carefully the assembly instructions before the installation. Do not discard this manual or any of the packaging material until the unit has been completely assembled.
RTA-2018 P.2 P.
RTA-2018 P.3 P.3 SCREWS LIST PART QTY SIZE / DESCRIPTION 🅐 4 6x45mm 🅑 8 6x30mm 🅒 6 6x12mm 🅓 8 4x12mm 1 Hex Wrench 1 Allen Wrench Hex/Phillips FIGURE BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. • Do a quick inventory to make sure the product contains all the parts and hardware. • Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card included with the product.
RTA-2018 P.4 P.4 ASSEMBLY STEPS Using the wrench, assemble the casters ② to the structures ①L, ①R in the following order: ☛ The locking casters ②L go on the front bottom holes, ☛ The non-locking casters ②N go on the back bottom holes. STEP 1 Non-locking at back N Locking at front L STEP 2 Panel ③ comes with metal inserts on its interior face, they look like screws but are nuts pre-aligned to receive the screws.
RTA-2018 P.5 P.5 Use screws Ⓑ to assemble the lower panel ④ to the lower bars on the structures ①L, ①R from underneath as shown. STEP 3 Screws: Ⓑ 6x30mm 4 Pcs STEP 4 Use screws Ⓑ to assemble the main panel ⑤ to the top bars of the structures ①L and ①R from underneath as shown. Screws: Ⓑ 6x30mm 4 Pcs STEP 5 Use screws Ⓓ to assemble the keyboard sliders ⑥ on their respective sides to the middle bars of the structures ①L and ①R from the inside.
RTA-2018 P.6 P.6 Use screws Ⓓ to assemble the keyboard panel ⑦ to the sliders ⑥ from underneath as shown. STEP 6 Screws: Ⓓ 4x12mm 4 Pcs STEP 7 Use screws Ⓒ to assemble the CD rack ⑨ to either structure ①L or ①R according tp your preference. Screws: Ⓒ 6x12mm 2 Pcs OR Use screws Ⓒ to assemble the support tubes ⑩A to the monitor/printer panel ⑧ as shown.
RTA-2018 P.7 STEP 9 P.7 Assemble the support tubes ⑩A to the main panel ⑤ in the position of your preference making sure that the protection clips ⑩B are positioned in between, then use the screw knobs ⑩C to secure the tubes as shown. The clips ⑩B go in between the tubes and the main panel. (This view is from the back side) ON THE BACK: ON THE LEFT: ON THE RIGHT: ALL DONE! Before you start using the unit, make sure that all the screws, bolts, cam locks, etc.
RTA-2018 P.8 P.8 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS: WEIGHT LIMITS 30 Lbs. (13.60 Kg) 100 Lbs. (45.36 Kg) 22 Lbs. (9.97 Kg) 30 Lbs. (13.60 Kg) • Do not exceed the indicated weight limits. • Do not expose the surfaces to direct sunlight or to extreme environmental conditions. • Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
