3/13 :: Introduction Thank you for purchasing this Team Associated product. This manual contains instructions and tips for building and maintaining your new RC8.2 RTR. Please take a moment to read through it an familiarize yourself with these steps as they will help you to understand each component’s function and show you some tips for getting the most out of your RC8.2 RTR.
:: Table of Contents 1....................Cover 24-25.........Shocks Install 2....................Introduction 25-29.........Radio Tray Assembly 3....................Table of Contents 29-32.........Fuel Tank, Air Filter, and Engine Assembly 4-5...............Front and Rear Diff Assembly 33................Wheel, Tires, and Body Assembly 6-7................Center Diff Assembly 34-36.........TechTips 7-8...............Steering, Servo, and Rear Camber Links Assembly 37-49.........
:: Front/Rear Differential Assembly 89115 Diff housing 89120 Diff washer 588 #6 rease g k c bla 89121 Diff O-Ring 89496 Diff outdrive 16mm bl 25236 8x16mm bearing # ac 65 8 k gr 8 ea se 89121 Diff O-Ring :: Front/Rear Differential Assembly (cont.) 89120 Sun gear 89120 Diff outdrive pin ! Align pin with groove in sun gear :: Front/Rear Differential Assembly (cont.
:: Front/Rear Differential Assembly (cont.) 89121 Diff O-Ring 89496 Diff outdrive 16mm 89120 Diff washer 89121 Diff O-Ring #6588 black grease 8 e 58 as #6 gre k c la b 25236 8x16mm bearing 89113 Diff ring gear :: Front/Rear Differential Assembly (cont.) 89120 Diff outdrive pin 89116 Diff gasket ! #6588 black grease Thin Gasket :: Front/Rear Differential Assembly (cont.) 89120 Sun gear ! Tighten screws evenly and firmly.
:: Center Differential Assembly 89115 Diff housing 89120 Diff washer bl 25236 8x16mm bearing # ac 65 8 k gr 8 ea se 89121 Diff O-Ring #6588 black grease 89121 Diff O-Ring 89496 Diff outdrive 16mm :: Center Differential Assembly (cont.) 89120 Sun gear 89120 Diff outdrive pin 89120 Spider gear assembly ! Align pin with groove in sun gear :: Center Differential Assembly (cont.
:: Center Differential Assembly (cont.) 89120 Diff washer 89120 Sun gear 89120 Diff outdrive pin 89121 Diff O-Ring ! Align pin with groove in sun gear :: Center Differential Assembly (cont.) ! 89116 Diff gasket 89208 x4 3x14mm fhcs Tighten screws evenly and firmly. #6588 black grease ! Diff fluid 5,000cst #5453 Fill with diff fluid to top of gears. :: Steering Turnbuckle Assembly 89074 x2 Steering eyelet 89268 42mm steel turnbuckle 17.
:: Servo Link Assembly 89078 x2 Straight eyelet 89267 32mm steel turnbuckle 7.5mm 89078 x2 balljoint :: Rear Camber Link Assembly 89076 x2 Camber pivot balls 89076 x2 Camber rod end 89269 38mm steel turnbuckle 89076 x2 Camber ball joints 7.
:: Shock Assembly - (cont.) 89215 Locknut (piston) 89353 Shock piston set (1.3, blank) 89260 Shock shaft, 29mm, (front) 89352 O-Ring 89278 x2 2.5mm piston washer 89261 Shock shaft, 38mm (rear) 89352 Bottom nut 89358 Upper shock tool :: Shock Assembly - (cont.) ! ! Sho c flui k d Short boots for front shocks. Fill to top with shock fluid: Long boots for rear shocks. Front: 40wt #5423 Rear 30 wt #5422 89556 RC8.2 shock boot (front shown) ! ck Sho d flui One drop of shock fluid on threads.
:: Shock Assembly - (cont.) Front shock: 7mm Rear shock: 2mm 89396 Shock pre-load clips 89293 x2 Front spring, silver (3.9lbs) (short spring) 89396 Shock pre-load clips 1mm 2mm 3mm 5mm 89348 x2 Rear spring, silver (3.
:: Steering Assembly (cont.) 31404 x2 6x10mm bearing 89016 Servo saver bolt 89015 Servo saver arm #65 88 ck gre ase bla 89015 Servo saver bellcrank ! gap setting: 2mm # thr 1596 ea dl ock 89117 x2 Diff shim 89016 Servo saver spring 89016 Servo saver retainer :: Steering Assembly (cont.) 89272 Steering rack 31404 x2 6x10mm bearing 89161 x4 5x8mm bearing 89015 Steering bellcrank 89014 x2 Steering rack post 89218 x2 Washer 3x8mm 25215 x2 M3 locknut :: Steering Assembly (cont.
:: Steering Assembly (cont.) / Front Gearbox Assembly #1596 thread lock 89214 x2 4x12mm fhcs #1596 thread lock 89114 Diff pinion gear 25215 x4 M3 locknut 25236 x2 8x16mm bearing 89017 Inner gearbox :: Front Gearbox Assembly - (cont.) 89278 x2 2.5mm washer ! 89036 Arm mount (B) Key setscrew onto flat side of shaft. Tighten with no endplay. 89221 5x4mm setscrew 89571 SC8.2e center drive line input cup 96 #15 lock d a e thr 89201 x2 2.
:: Front Gearbox Assembly - (cont.) 89225 x2 3x24mm shcs 96 #15 lock ad e r th 89549 Front upper arm 89473 x2 Steel shock standoffs 96 #15 lock ad e thr 89218 x2 3x8mm washer 89586 Front shock tower (front) 89269 38mm steel turnbuckle 89076 Camber rod ends 7.5mm ! Smooth edge towards drivers side! Build right and left sides! :: Front Gearbox Assembly - (cont.
:: Front Suspension Assembly 89102 CVA bone 89105 CVA pin #6588 black gre ase 8 #658 e greas black 89105 CVA u-joint coupler 89573 Lightweight cv axle, steel ! ! ! Axle has additional holes for crosspin to extend the life of the Axle. Build Two! :: Front Suspension Assembly - (cont.
:: Front Suspension Assembly - (cont.) 89029 Steering block bushing (short) Note: direction ! 89206 4x10mm bhcs blue 16 deg 16 deg red 89032 16 deg. caster angle bushing (red) 89029 Steering block bushing (long) ! Do not tighten until bushing is keyed into steering block. 89207 4x12mm bhcs ! 89032 16 deg. caster angle bushing (blue) Note: Key bushings into steering block. ! Build right and left sides! :: Front Suspension Assembly - (cont.
:: Front Suspension Assembly - (cont.) ! Build right and left sides! hinge pin bushing 2 dot down 25215 x2 M3 locknut 89039 x2 Hinge pin bushings (two dot, down) 89035 Arm mount (A) 89228 x2 3x40mm shcs 89218 x2 3x8mm washer :: Front Suspension Assembly - (cont.) Side View 89031 x4 Blue 1.7mm caster spacer 25215 x2 M3 locknut 89225 x2 3x24mm shcs ! Build right and left sides! :: Front Suspension Assembly - (cont.) 25225 x2 3x3mm setscrew # thr 1596 ead loc k 89088 2.
:: Front Suspension Assembly - (cont.) 25215 M3 locknut 89022 Front bumper 89217 x2 4x14mm fhcs 89214 x4 4x12mm fhcs #15 9 ead 6 lock thr 25204 3x16mm fhcs :: Rear Gearbox Assembly 25215 x2 M3 locknut 25236 x2 8x16mm bearing 89114 Diff pinion gear ! Key setscrew onto flat side of shaft. Tighten with no endplay. 89221 5x4mm setscrew 89571 SC8.
:: Rear Gearbox Assembly - (cont.) 89039 x2 Hinge pin bushing (2 dot down) hinge pin bushing 89037 Arm mount (C) 2 dot down 89211 3x26mm fhcs 89258 Chassis brace (rear) 89218 x2 3x8mm washer 89224 x2 3x16mm shcs 25215 M3 locknut :: Rear Gearbox Assembly - (cont.) 89225 x2 3x24mm 89473 x2 shcs Steel shock standoff 89011 Body mount and spacer 25215 x2 M3 locknut #15 9 ead 6 lock thr 89218 x2 3x8mm washer 25192 x2 3x20mm shcs 89587 Rear shock tower (rear) :: Rear Gearbox Assembly - (cont.
:: Rear Gearbox Assembly - (cont.) ! 89472 Front bulkhead spacer Diff shims installed to diff, diff installed to gearbox. ! ! 89224 x2 3x16mm shcs 89117 x2 Diff shim 89017 Outer gearbox :: Rear Suspension Assembly 89162 15x21mm bearing ! th #15 re ad 96 lo ck 89572 SC8.2e dogbone axle 89107 Bearing shield Build right and left sides! 89096 Wheel hex pins 89033 hub carrier (left, right) 25236 8x16mm bearing 89251 Wheel hex 89221 5x4mm setscrew :: Rear Suspension Assembly - (cont.
:: Rear Suspension Assembly - (cont.) ! Build right and left sides! 31520 2.5x6mm bhcs 89031 x2 Hub spacers (red) 89575 x2 SC8.2e dogbone (82mm) 89041 Outer hinge pin :: Rear Suspension Assembly - (cont.) 89278 x2 2.5mm washer 89201 x2 2.5x3mm bhcs 89038 Arm mount (D) 89218 x2 3x8mm washer 89228 x2 3x40mm shcs # thr 1596 ead loc k 89040 x2 Inner hinge pins :: Rear Suspension Assembly - (cont.) 25215 M3 locknut 89089 2.
:: Rear Suspension Assembly - (cont.) 89202 x2 3x12mm bhcs 89218 x2 3x8mm washer 89592 RC8.2e RTR wing (black) 25192 x2 3x20mm shcs 89540 RC8.2 wing mount upper brace 25215 x2 M3 locknut 89540 x2 RC8.2 wing mounts 25215 x2 M3 locknut :: Rear Suspension Assembly - (cont.
:: Rear Suspension Assembly - (cont.) 25215 M3 locknut 89217 x2 4x14mm fhcs 25204 3x16mm fhcs 89214 x2 4x12mm fhcs :: Center Bulkhead Assembly 89019 Center bulkhead (top) 89122 x2 Brake pads brake pad gap: 4.
:: Center Bulkhead Assembly (cont.) ! Do not tighten #89226 3x26mm shcs completely until the next step! ! ! ! ! 89226 x4 3x26mm shcs 89254 Center diff top plate 89124 x2 Brake cam 89019 x2 Center bulkhead (bottom) :: Center Bulkhead Assembly - (cont.
:: Shocks Install 89083 Shock bushing ! Note the direction of the shock cap when installing onto shock standoffs ! 25612 M3 locknut with flange Install two front shocks. :: Shocks Install - (cont.) 89454 3x12mm shcs ! After installation, adjust droop screw to get a front shock length of 103mm measured center to center on the shock cap / shock mount pin. 91069 Shock mount pin, steel :: Shocks Install - (cont.
:: Shocks Install - (cont.) 89454 3x12mm shcs ! After installation, adjust droop screw to get a rear shock length of 122mm measured center to center on the shock cap / shock mount pin. 91069 Shock mount pin, steel :: Radio Tray Assembly 89004 Receiver box foam pad (bottom) 89003 Wire insert 89253 Antenna mount 6338 Antenna tube and cap 89222 x2 2.5x8mm shcs 89003 Receiver box top 89003 Switch mount Receiver 89004 Receiver box foam pad (top) 89003 Receiver box :: Radio Tray Assembly - (cont.
:: Radio Tray Assembly - (cont.) 89218 x8 Washers 3x8mm 31531 x3 3x6mm bhcs 25187 x8 3x14mm bhcs Throttle servo Transponder and 3x6mm bhcs not not inlcluded! Steering servo ! ! 89006 x4 Servo spacers ! Servo mounts vary per servo manufacturer. Space your servos low to the chassis without touching the bottom. :: Radio Tray Assembly - (cont.
:: Radio Tray Assembly - (cont.
:: Radio Tray Assembly (cont.) 25203 x6 3x12mm fhcs 89205 3x26mm bhcs ! 25215 M3 locknut There will be an unused screw hole at the bottom of the receiver box. This will not be used for the RC8.2 :: Radio Tray Assembly (cont.) 0.5mm 89126 x2 Brake washer 89126 x2 brake spring (silicone) 25225 x2 3x3mm setscrew 89126 x2 Set collar ! After installation, leave a 0.
:: Radio Tray Assembly (cont.) 1mm gap :: 2 :: Brake bias adjusters :: 6 :: Rear :: 5 :: Front :: 9 :: 1 :: 3 :: 4 ::1 - Turn on transmitter and buggy. Adjust servo horn until position is parallel with centerline at neutral. ::5 - Pull cams to engage brakes. Set collar (with brakes engaged) to have 1mm gap between tubing and collar. ::7 - Set throttle EPA to max. Apply full throttle on transmitter and set EPA so that the carb is full open. Be careful not to over-extend the carb.
:: Air Filter Install ! oi filt l # er 77 10 Pullstart engine 89142 Air filter outer element When oiling the filter elements, place both inside a plastic bag and squeeze to help evenly coat the filter.
:: Engine Install (cont.) 25226 4x5mm setscrew #1596 thread lock 89130 x2 Engine mount plates 89144 Pipe mount th #15 re ad 96 lo ck #1596 thread lock 25201 3x8mm fhcs 89145 Pipe wire 89213 x6 4x6mm fhcs :: Engine Install (cont.
:: Engine Install (cont.) Pressure line from fuel tank lid to exhaust pipe nipple Fuel line from fuel tank to carburetor :: Engine Install (cont.) 89325 x2 Fuel line clips ! ! ! ! Install fuel line clips! ! Adjust angle of carb ball joint to align with throttle servo.
:: Wheels, Tires, and Body Install 97 #15 lue ire g CA t Tires: When gluing tires to wheels, use a fast-curing Tire glue (CA) (AE Pt#1597). This is available at your local hobby shop. Make sure to clean the mounting surface of the tire with alchohol for best adhesion. 89255 x4 RTR Pre-glued wheel/tire :: Wheels, Tires, and Body Install (cont.) 89498 or 89499 RC8.
:: Building Tips Tires: The tires need to be glued to the wheels using any fast-curing FT Tire glue (CA) (AE Pt#1597). This is available at your local hobby shop. Make sure to clean the mounting surface of the tire with alchohol for best adhesion. Receiver Pack: Your RC8.2 does not come with a receiver pack. It is recommended that you use a 5-cell 1600mah pack (minimum) in either stick (AE Pt #612) or hump (AE Pt#613) pack configuration (your RC8.2 will accepteither).
:: Front End Tips (cont.) Front Camber Link-Outer: The standard short location will work the best for most tracks. Going to the long front link will give you more steering, but can make the car less predictable in bumps and exiting turns. Front Camber Angle: A good starting camber setting is –2 degrees. Positive camber, where the top of the tire is leaning out, is typically not recommended. Front Toe-In: Zero degree toe-in (tires pointing straight forward) is a good starting setting.
:: Droop Settings (Buggy shown but applicable for all vehicles) Note: Rear hub spacing is not recommended with RTR dog bones. For more adjustability, use CVA’s in place of dog bones. Step 1: With only the bottom of the shocks attatched, the droop screws raised all the way, and the chassis above your working surface so the arms are at full extension, you should be able to easily slide the top of your shock over the standoff screw, while leaving the shock at full extension.
:: Shocks 25612 89065 89066 89067 89083 89215 89260 89261 89278 89335 89351 89352 89353 89354 89396 89556 89580 89582 :: Front and Rear Gear Differential M3 Locknut With Flange Shock Rod End Shock O-Rings Shock Limiters, Set Shock Bushings Piston Locknut 29mm RTR Shock Shaft, Front 38mm RTR Shock Shaft, Rear 2.5mm Washer 16mm Shock Caps 16mm Shock Bladders 16mm Shock Rebuild Kit 16mm Shock Pistons 16mm Shock Spring Cups 16mm RTR Pre-load Clips, Shock Collar Set RC8.
:: Top Plate :: Shock Fluid 5420 5421 5422 5423 5424 5425 5426 5427 5428 5429 5430 5431 5432 5433 5434 5435 5436 5437 5438 10 Weight Silicone Shock Fluid 20 Weight Silicone Shock Fluid 30 Weight Silicone Shock Fluid 40 Weight Silicone Shock Fluid 22.5 Weight Silicone Shock Fluid 80 Weight Silicone Shock Fluid 27.5 Weight Silicone Shock Fluid 15 Weight Silicone Shock Fluid 25 Weight Silicone Shock Fluid 35 Weight Silicone Shock Fluid 45 Weight Silicone Shock Fluid 55 Weight Silicone Shock Fluid 32.
:: Front Gearbox 25215 25236 31531 89017 89035 89036 89039 89040 89114 89201 89214 89217 89218 89219 89221 89224 89226 89228 89278 89472 89571 89584 20 2 10 1 1 1 1 1 1 10 10 10 10 10 10 10 10 10 20 2 2 1 M3 Locknut 8x16x5 Bearing 3x6mm BHCS FR/RR Gearbox Arm Mount A Arm Mount B Hinge Pin Bushings, Set Inner Hinge Pin, Set Diff Pinion Gear 2.5x3mm BHCS 4x12mm FHCS 4x14mm FHCS 3x8mm Washer 3x5mm Setscrew 5x4mm Setscrew 3x16mm SHCS 3x26mm SHCS 3x40mm SHCS 2.5mm Washer RC8B Front Bulkhead Spacer SC8.
:: Rear Gearbox 25215 25236 31531 89017 89037 89038 89039 89040 89114 89201 89211 89214 89217 89218 89219 89221 89224 89278 89279 89472 89571 89583 M3 Locknut 8x16x5 Bearing 3x6mm BHCS RC8 FR/RR Gearbox, Set Arm Mount C Arm Mount D RC8 Hinge Pin Bushings, Set Inner Hinge Pin, Set RC8 Diff Pinion Gear 2.5x3mm BHCS M3x26mm FHCS 4x12mm FHCS 4x14mm FHCS 3x8mm Washer 3x5mm Setscrew 5x4mm Setscrew 3x16mm SHCS 2.5mm Washer 3x45mm SHCS RC8B Front Bulkhead Spacer SC8.
:: Front Shock Tower 89039 89202 89218 89225 89473 89586 :: Rear Shock Tower Hinge Pin Bushings, 1/2/3dot Set 3x12mm BHCS 3x8mm Washer 3x24mm SHCS RC8B Steel Shock Stand-offs Front Shock Tower 1 10 10 10 4 1 25192 25215 89011 89218 89225 89454 89473 89587 3x20mm SHCS M3 Locknut Body Mount Set 3x8mm Washer 3x24mm SHCS 3x12mm SHCS RC8 Steel Shock Standoffs Rear Shock Tower 20 20 1 10 10 10 4 1 89225 89225 89218 89218 89225 89225 89586 89473 89587 89473 89218 89011 25215 25215 25192 89039 89
:: Radio Tray 6338 21173 25187 25203 31531 89003 89004 89005 89006 89209 89214 89218 89222 89253 89454 89471 Antenna Tube and Cap 18T Body Clips 3x14mm BHCS 3x12mm FHCS 3x6mm BHCS RC8 Receiver/Battery Box, Set RC8 Receiver Box Pads, Set Aluminum Antenna Mount, Set RC8 Servo Mount Spacers, Set 3x18mm FHCS 4x12mm FHCS 3x8mm Washer 2.5x8mm SHCS Antenna Mount, Set 3x12mm SHCS RC8.
:: Chassis 25201 25226 89018 89022 89130 89144 89145 89207 89213 89224 89231 89257 89476 89552 3x8mm FHCS 4x5mm Setscrew RC8 Gearbox Gasket RC8 Front Bumper RC8 Engine Mount Plates RC8 Pipe Mount RC8 Pipe Mount Wire 4x12mm BHCS 4x6mm FHCS 3x16mm SHCS 3mm Lock Washer RC8 Engine Mount RC8B +3mm Chassis RC8.2 Side Guards 20 20 4 1 2 1 1 10 10 10 10 2 1 Pr.
:: Body / Decals :: Wheels / Tires 89152 89153 89255 89296 89297 RC8 RC8 RTR RC8 RC8 Wheels (White) Wheels (Yellow) Pre-Glued Wheel/Tire (White) 83mm Wheels (White) - Kit 83mm Wheels (Yellow) 4 4 Pr. 4 4 2208 31531 89150 89275 89276 89277 89497 89498 89499 89523 89559 Large Hood Pins 3x6mm BHCS RC8 Body w/Window Mask (Clear) RC8 RTR Body (Black) RC8 RTR Body (White) RC8 RTR Body Wrap Decals RC8.2 RTR Decal Sheet RC8.2 RTR Body (Gray) RC8.2 RTR Body (White) RC8e Body w/Window Masks (Clear) RC8.
:: Clutch 25237 89127 89132 89133 89134 89135 89136 89137 89138 89148 89157 89158 89159 89218 89223 89265 89375 89376 :: Exhaust 5x10x4 Bearings Clutch Bell, 17T Clutch Bell, 16T - Kit Clutch Springs 1.0 - Kit Clutch Shoes (aluminum) w/ Shims, Set Clutch Nut Flywheel (Hard Anodized) Clutch Shims Flywheel Collet Clutch Bell Shim Set 0.9 Clutch Springs 1.
:: Factory Team and Option Parts 25392 31550 80930 89005 89012 89016 89020 89045 89053 89054 89070 89071 89073 89082 89094 89095 89123 89136 89146 89160 89161 89229 89234 89235 89236 89237 89284 89285 89286 89290 89291 89344 89346 89355 89380 89381 89405 89406 89456 89460 89461 89462 89463 89464 89465 89466 89467 89468 89469 89470 89473 89476 89477 89478 89481 89482 89485 89487 89488 89489 89490 89492 89494 89495 89496 89529 89530 89531 89532 89533 89534 89535 3mm Blue Locknut, Flanged M3 Aluminum Lock
:: Reedy Nitro Engines and Parts 800 801 802 28000 28001 28002 28003 28004 28005 28006 28007 28008 28009 28010 28011 28012 28013 28014 28015 28016 28017 28018 28019 28020 28021 28022 28023 28024 28025 28026 28027 28028 28029 28030 28031 28032 28033 28034 28035 28036 28037 28038 28039 28040 28041 28042 28043 28044 28045 28046 28047 28048 28049 28050 Reedy 121VR .21 Off-Road Comp. Nitro Engine Reedy 121VR-ST .21 Comp. Nitro Engine Reedy .
:: Tools :: 1/8 Kits and RTR’s 20501 MGT 4.60 SE RTR (ready-to-run) 20502 MGT 8.0 Nitro RTR (ready-to-run) 20503 Limited Edition MGT 4.60 Nitro RTR, w/flag body (ready-to-run) 20504 Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run) 80905 RC8RS “Race Spec” Nitro Buggy RTR (ready-to-run) 80906 RC8.2 Nitro Buggy FT Kit 80907 RC8.2e Electric Buggy FT Kit 80908 RC8.2e Electric Buggy RTR (ready-to-run) 80909 RC8.2 Nitro Buggy RTR (ready-to-run) 80912 RC8T Championship Edition 80933 SC8.
:: RePlay Cameras RP001 RP002 RP021 RP022 RP023 RP029 RP030 RP032 RP033 RP034 RP036 RP037 RP038 RP041 RP042 RP043 RP044 RP045 RP046 RP047 RP048 RP049 RP054 Replay XD1080 Complete Camera System Replay XD720 Complete Camera System Replay XD1080 Lens Bezel Kit Replay XD1080 Clear Lens Cover Replay XD1080 Lens Bezel & Rear Cap O-Ring Replay XD1080 HDMI to Mini-HDMI Replay XD1080 Mini 8-pin USB Charge Data Cable USB DC Car Charger 1A Stubby USB DC Car Charger 500mAh Micro SDHC USB Reader 3M VHB 4991 Mount Ad
:: Notes
Driver: Track: Setup Sheet Conditions: Front Suspension Anti Roll Bar: Steering System: 2.2mm 2.5mm 2.8mm 3.0mm Black Silver Gold Black 0 Camber: -1 Toe: 3 2.2mm 2.5mm 2.8mm 3.0mm 1 back mid front Front # Up 0 B A 3 Black Silver Gold Black 1 Wheelbase: Upper Hinge Pin Bushing 16 deg Caster: Rev.1 Rear Suspension Anti Roll Bar: Stock Rack Swing Rack Bellcrank Rack Bumpsteer Washers: Date: Event: RC8.
:: Hardware - 1:1 Scale View Flat Head (fhcs) Button Head (bhcs) Cap Head (shcs) 3x8mm (25201) 2.5x8mm (89222) 2.5x3mm (89201) 3x10mm (25202) 3x8mm (89223) 2.
Driver: Track: Setup Sheet Conditions: Front Suspension Anti Roll Bar: Steering System: 2.2mm 2.5mm 2.8mm 3.0mm Black Silver Gold Black 3 2 2.2mm 2.5mm 2.8mm 3.0mm 1 back mid front Camber: Caster: Front # Up B A 3 Black Silver Gold Black 2 1 Wheelbase: Upper Hinge Pin Bushing Toe: Rev.
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated http://bit.ly/AEonFacebook call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.
