User manual

ManualsBrandsTE CONNECTIVITY ManualsPCB ConnectorsSocket enclosure - cable AMPMODU Total number of pins 7 Contact spacing: 2.54 mm 1 pc(s)

Application Specification

Locking Clip

0.64- mm [.025- in.] Square

114--25006

LOC B

1 of 9

E2010 Tyco Electronics Corporation, Berwyn, PA

TE logo and Tyco Electronics are trademarks.

*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.

TOOLING ASSISTANCE CENTER 1--800--722--1111

PRODUCT INFORMATION 1--800--522--6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

Contacts and Housings

03 MAR 10 Rev F

All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and

inches]. Unless otherwise specified, dimensions have a tolerance of +

0.13 [+.005] and angles have a tolerance of +2_.

Figures and illustrations are for identification only and are not drawn to scale.

1. INTRODUCTION

This specification covers requirements for the application of Locking Clip 0.64--mm [.025--in.]

0.03 [+.001]) Square Contacts and Housings. The contacts are designed to mate with 0.64 [.025] square

posts with a maximum corner radius of 8.08 mm [.003 in.]. The contacts feature a locking lance, contact

spring, stabilizer, and wrap--around insulation barrel. The contact spring provides high contact--to--post

retention, while the locking lance holds the contact in the housing. The stabilizer maintains alignment of the

contact in the housing and the wrap--around insulation barrel is a feature which allows for wire with large

insulation diameters.

Housings are available in various sizes (number of contact cavities) with single-- and double--row contact

cavities on 2.54 mm [.100 in.] centerlines. Double--row housings are available in three configurations: both

ends closed, right end open, and left end open. Single--row housings are available only in both ends closed.

Right end open configurations are designed with a key and left end open configurations are designed with a

keyway. This design enables these housings to be stacked on the pc board for circuit grouping. Each contact

cavity in the housing features a cavity rib for contact polarization, and when loaded, the housings mate with the

posts. Each housing features an extraction slot which is used to remove individual contacts from the housing.

These requirements apply to hand and semi--automatic application tooling.

Figure 1 provides terminology for contact and housing features that will be used throughout this specification.

Use of these terms will facilitate assistance when corresponding with Tyco Electronics Representatives.

Figure 1

Wrap--Around

Insulation

Barrel

Stabilizer

Double- Row Housing,

Left End Open

Double- Row Housing,

Right End Open

Single-Row Housing,

Both Ends Closed

Locking Clip 0.64- mm [.025- in.]

Square Contact

Contact

Spring

Extraction

Slot

Double- Row Housing,

Both Ends Closed

Key

Keyway

Cavity Rib

Contact

Cavity

Locking

Lance

Extraction

Slot

NOTE

Summary of content (9 pages)

PAGE 1
Application Specification Locking Clip 0.64- mm [.025- in.] Square Contacts and Housings NOTE i 114-- 25006 03 MAR 10 Rev F All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_. Figures and illustrations are for identification only and are not drawn to scale. 1.
PAGE 2
Locking Clip Contacts and Housings 114- 25006 2. REFERENCE MATERIAL 2.1. Revision Summary This paragraph is reserved for a revision summary of changes and additions made to this specification. The following changes were made for this revision. S Updated document to corporate requirements S New logo and format 2.2. Customer Assistance Reference Part Number 87124 and Product Code 5403 are representative numbers of Locking Clip 0.64--mm [.025--in.] Square Contacts and Housings.
PAGE 3
Locking Clip Contacts and Housings NOTE 114- 25006 If the post is longer than the maximum specified, the post tip might butt against the wire. i Note: Not to Scale 0.64-- mm [.025-- in.] (+0.03 [+.001]) Square Post with Maximum Corner Radius of 0.08 [.003] 2.54 x 2.54 [.100 x .100] 5.08-- 7.04 [.200-- .277] (Without Housing) 6.93-- 8.89 [.273-- .350] (With Housing) Figure 3 3.4. Terminated Conductor Requirements A.
PAGE 4
Locking Clip Contacts and Housings 114- 25006 6. Bellmouth The front and rear bellmouths result from the protrusion of the metal of the wire barrel after the crimping process. The dimensions must not exceed the limits shown in Figure 4. 7. Effective Crimp Length Effective crimp length is defined as that portion of the wire barrel, excluding bellmouth, which is fully formed by the crimping tool; it is shown in Figure 4. Insulation Insulation Barrel Crimp Wire Barrel Crimp Wire Barrel Seam 2.03 [.
PAGE 5
Locking Clip Contacts and Housings 114- 25006 8. Vertical Alignment The contact, including the cutoff tab and burr, may not be bent above or below the datum line more than is shown in Figure 5. 3_ (Max) Datum Line 3_ (Max) Figure 5 9. Horizontal Alignment The side to side bending of the contact may not exceed the limits shown in Figure 6. 3_ (Max) Datum Line 3_ (Max) Figure 6 10.
PAGE 6
Locking Clip Contacts and Housings 114- 25006 D. Locking Lance Locking lance may not be deformed or damaged. Dimensions are given in Figure 4. E. Stabilizer After crimping, the stabilizer may not be deformed. See Figure 8. Stabilizer Crimped Contact Figure 8 3.5. Housing A. Keying Plugs Keying plugs provide housing identification and polarization by not allowing a post to enter the contact cavity where the keying plug is installed. The latch must be oriented with the extraction slot cavity.
PAGE 7
Locking Clip Contacts and Housings 114- 25006 B. Strain Relief If required, the wires can be bundled together with cable ties and secured to a panel with fixed clamps. The wires must not be confined in any way that would restrict floating action of the contact in the housing. 1. Cable Ties The minimum distance for the cable tie, measured from the back of the housing to the first cable tie, is shown in Figure 10. 2.
PAGE 8
Locking Clip Contacts and Housings 114- 25006 Stacking Double- Row Housings Right End Open Key Left End Open PC Board Figure 11 3.6. Repair A damaged contact can be removed independently of all other contacts and replaced with a new one. All contacts must be removed from a damaged housing and the housing replaced with a new one. 4. QUALIFICATIONS Locking Clip Contact and Housing Assemblies are Component Recognized by Underwriters Laboratories Inc.
PAGE 9
Locking Clip Contacts and Housings 114- 25006 6. VISUAL AID Figure 13 shows a typical application of Locking Clip 0.64--mm [.025--in.] Square Contacts and Housings. This illustration should be used by production personnel to ensure a correctly applied product. Applications which DO NOT appear correct should be inspected using the information in the preceding pages of this specification and in the instructional material shipped with the product.