Information

114- 40030
Rev D6 of 13
CABLE
DIAMETER
ACCEPTED
CABLE
CRIMP
“A”
CABLE
CRIMP
“B”
SHIELD
CRIMP
“C”
4.19--4.83 [.165--.190] 4.5 + 0.13 [.177 + .005] 10.21 [.402]
4.83--5.51 [.190--.217] 5.41 + 0.13 [.213 + .005] 9.58 [.377]
5.51--6.25 [.217--.246] 6.07 + 0.13 [.239 + .005] -- -- --
6.25--7.21 [.246--.284] 6.68 + 0.13 [.263 + .005] 10.85 [.427]
10.9 + 0.13
7.21--8.23 [.284--.324] 7.65 + 0.13 [.301 + .005] -- -- --
1
0
.
9
+
0
.
1
3
[.429 + .005]
8.23--9.52 [.324--.375] 8.66 + 0.13 [.341 + .005] -- -- --
9.52--11.10 [.375--.437] 9.98 + 0.13 [.393 + .005] -- -- --
10.16--11.56 [.400--.455] 10.49 + 0.13 [.413 + .005] -- -- --
5.84--6.73 [.230--.265] 6.43 + 0.2 [.253 + .008] -- -- --
8.58--9.78 [.338--.385] 9.14 + 0.2 [.360 + .008] 1 1 .84 [.466]
9.52--10.97 [.375--.432] 10.16 + 0.2 [.400 + .008] 12.95 [.510]
13.72 + 0.2
[
5
4
0
+
0
0
8
]
10.72--12.45 [.422--.490] 10.72 + 0.2 [.422 + .008] 16.00 [.630]
[
.
5
4
0
+ .
0
0
8
]
12.19--14.27 [.480--.562] 12.19 + 0.2 [.480 + .008] 16.00 [.630]
Figure 4 (end)
3.6. Hardware and Accessories
The AMPLIMITE HDP--20 Connectors are compatible with the mounting hardware and accessories as shown
in Figure 5. The instructional material listed (in parentheses) with each accessory provides details for product
selection and assembly procedures.
A. Shielding Hardware Kits
Shielding Hardware Kits (Instruction Sheet 408--9010) and Shielding Hardware Enclosure Kits (Instruction
Sheet 408--9172) are available for AMPLIMITE connectors. Hardware kits include a connector and inner
and outer shield halves. Enclosure kits also include a protective flexible thermoplastic enclosure and two
male jackscrews. The thermoplastic enclosure is assembled to the kit using Shielding Enclosure
Expansion Tools with base PN 58241 (Instruction Sheet 408--9199). Cable ferrules must be purchased
separately.
B. Cable Clamp Assembly Kits
Cable clamp assembly kits are available in straight/45_ and straight/90_ versions (Instruction Sheet
408--7555). The clamp assemblies can be mated using spring latches (Instruction Sheets 408--9130,
408--9131) and latching blocks (Instruction Sheet 408--9128), or using screwlocks and retainers
(Instruction Sheet 408--7837).
C. Shielded Cable Clamp Assembly Kits
Metal RFI/EMI Shielded Cable Clamp Assemblies come in two--piece kits, and are available in both
straight--exit (Instruction Sheet 408--6609) and 90_--exit (Instruction Sheet 408--6769) versions. Unlike the
hardware kits, these cable clamp kits allow the cable to be fully prepared and terminated to the connector
before shield installation. The straight--exit shield is attached to the connector using saddle washers and
screws. T he 90_--exit shield is attached using slide latches and screws.
D. Jacketed Shielded Cable
For applications using jacketed shielded cable with AMPLIMITE shields (see subparagraph C), two ferrule
options are available. As split--ring ferrule is used with a foil or braided shield and is not crimped. An inner
and an outer crimped ferrule are used with applications using braid--shielded cable only.
E. Slide Latch Assemblies and Clips
One--Piece Slide Latch or Two--Piece Slide Latch Clips (Instruction Sheet 408--6551) attach to the
connector mating face. The mating connector uses Locking Post Assemblies which latch into the slide
latch assembly.