RoHS Ready AMP Circular Connectors for Commercial Signal & Power Applications
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Introduction Product Facts ■ Certified by ■ Lightweight, all-plastic and Canadian Standards Association, File No.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Connector Series and Types . . . . . . . . . . . . .
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Connector Series and Types Series 1—Size 16 Contacts 1 3 4 7 6 11 12 14 Series 1 connectors permit the use of multiple combinations of signal and coaxial circuits in the same housing by accepting durable Multimate contacts. These pin and socket contacts include Type III+ and subminiature coaxial contacts, interchangeable in the same Multimate contact cavity. Type III+ contacts (.062 [1.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Connector Series and Types (Continued) 1 Series 5—Power Contacts .125 POWERBAND 2 Series 5 connectors combine the revolutionary performance of the new AMP POWERBAND Contact, high current contact in configurations similar to the Series 3 connectors. AMP POWERBAND contacts offer the electrical 3 2 3 1 8 9 10 Series 6—Combination, Size 16 and .
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Levels of Protection for Electric Operating Material According to IEC 60529 and IEC 60947, Appendix C Environmentally Protected Circular Plastic Connectors, for Mated CPC Connectors Utilizing Peripheral Seals and either Wire Entry Seals (for Discrete Wire Applications) or Heat Shrink Boots (for Jacketed Cable Applications). Available are Various Sizes, Series 1, 5 and 6.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Current Carrying Capabilities The total current capacity of each contact in a given connector is dependent upon the heat rise resulting from the combination of electrical loads of the contacts in the connector arrangement and the maximum ambient temperature in which the connector will be operating.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Presentation — An Example* Current Rating ■ First, a base curve showing current levels versus T-rise for a single circuit and the largest wire size (See figure 1). This represents the maximum current capacity of the contact. The curve is usually flat up to 75°C ambient and then drops off.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connectors, Size 1 CPC Connectors, Series 1 for Cable or Panel Mount Square Flange Receptacle *G ±.025 [±0.64] (Accepts Type III+, HighCurrent Power, Type II and Subminiature Coax Contacts) CPC Series 1 *D ±.010 [±0.25] *J Dia. *F ±.010 [±0.25] *Panel Thk. .125 [3.18] Max. *F ±.010 [±0.25] *E Max. *H *A Max. *B +.007 –.000 Dia. [+0.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connectors, Series 1, VDE Tested CPC Connectors, Series 1, for Cable or Panel Mount (Accepts Type III+, HighCurrent Power, Type II and Subminiature Coax Contacts) Square Flange Receptacle *G ±.025 [±0.64] *F ±.010 [±0.25] *E Max. CPC Series 1 *D ±.010 [±0.25] *J Dia. *F ±.010 [±0.25] *Panel Thk. .125 [3.18] Max. +.007 *H –.000 Dia. [+0.18] *A Max.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Circular Plastic Connectors, Series 1 1.435±.015 [36.45±0.38] Square Flange Receptacles, Printed Circuit Board Mount .094 [2.39] 1.125±.010 [28.58±0.25] Typ. with .025 [0.64] sq. solder tails .420±.015 [10.67±0.38] B CPC Series 1 .150 Dia. [3.81] 4 Holes 1.435±.015 [36.45±0.38] 1.050±.010 [26.67±0.25] Dia. 1.125±.010 [28.58±0.25] Typ. A .125 Max. [3.18] Panel Thk.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connectors, Series 1 (Continued) Square Flange Receptacles, Printed Circuit Board Mount 1.050 [26.67] 1.435±.015 [36.45±0.38] .094±.005 [2.39±0.13] .420±.005 [10.67±0.13] 1.125±.005 [28.58±0.13] with .025 [0.64] sq. solder tails 1.050±.005 Dia. [26.67±0.13] 1.435±.015 [36.45±0.38] 1.110 Max. Dia. [28.19] ±.030 A [±0.76] Typ.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connectors, Series 1 (Continued) Special CPC Connectors, Square Flange Receptacles, With Solder Type Contacts (Size 16), Contact Arrangement 17-16 .420±.015 [10.67±0.38] CPC Series 1 .094±.010 [2.39±0.25] 1.090±.010 [27.69±0.25] Dia. 1.050±.010 Dia. [26.67±0.25] Panel Thk. .125 Max. [3.18] .250±.015 [6.35±0.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connectors, Series 1 (Continued) Square Flange Receptacles, Right-Angle, Posted with .025 [0.64] sq. solder tails *A Max. *B *C CPC Series 1 *D Max. *E Max. .150 [3.81] Material and Finish Housing—Thermoplastic, 94V-0 rated, black Location Wafer—Phenolic, black Contact Posts—.000100 [0.00254] min. tin over .000100 [0.00254] min. copper Contact Body— A—.000100 [0.00254] min.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connectors, Series 1 (Continued) Square Flange Receptacles, Right-Angle, Posted with .045 [1.14] sq. solder tails. For Higher Current Applications Receptacle Mail: Thermoplastic Color: Black Mating Face CPC Series 1 Major Key .520±.015 [13.2±.381] 2.43 Ref. [61.72] 1.33 Max. [33.78] .156 [3.96] Ø 1.45 Max. [36.83] Ø 1.51 Max. [38.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Signal Contacts Type III+, Crimp, Snap-In [.0625 +.0010 –.0020 Dia. [1.588+0.025 –0.051] Pin Body Ferrule, Brass, Nickel Flash .113 Max. [2.87] Dia. Pin Socket Material and Finish — See chart. .530±.010 [13.46±0.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Signal Contacts (Continued) CPC Series 1 Enhanced High Current Type III+, Crimp, Snap-In [.0625 +.0010 –.0020 Dia. [1.588+0.025 –0.051] Pin Body Spring, Stainless Steel Spring, Stainless Steel .390 Min. [9.91] Pin Ferrule, Brass, Nickel Flash .113 Max. [2.87] Dia. Pin Socket .530±.010 [13.46±0.25] Material and Finish — See chart.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Signal Contacts (Continued) Type III+ (Precision Formed, Crimp) Grounding Pin Contact Size—16 Pin Diameter—.062 [1.57] Related Product Data (make first - break last) Material and Finish CPC Series 1 Performance Characteristics—Page 6 Application Tooling—Pages 76-79 Technical Documents—Page 80 Contact Body—Copper alloy, plated tin or gold Spring—Stainless steel AWG Ins. Dia.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Signal Contacts (Continued) Type III+ (Precision Formed, Solder) Solder-Type (with Preformed Wire Barrel/Insulation Support) CPC Series 1 Contact Size—16 Pin Diameter—.062 [1.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Signal Contacts (Continued) Type II, Screw Machined, Crimp 1.087±.010 [27.61±0.25] Material Contact Body—Brass Retention Spring—Stainless steel .472±.005 [11.99±0.13] CPC Series 1 Finish Contact Body—.000030 [0.00076] gold over .000050 [0.00127] nickel. Gold thickness controlled on socket O.D. Retention Spring—Stainless steel Pin .107 [2.72] Max. Dia. .062±.001 Dia. [1.57±0.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Coaxial Contacts Subminiature Coax, Size 16 Precision Formed, Crimp 1.010 Ref. [25.65] CPC Series 1 Pin .650 [16.51] Ref. Pin Socket 0 .107+.005 –.000 [2.718+.127 ] –.000 Dia. .250 [6.35] .112+.005 A±.003 ±.076 Dia. [2.845+.127] Dia. Ferrule .120 Part No. 5-225088-1— A [3.05] Dia. Socket .084 .086 [2.134] [2.184] Dia. .235 [5.969] Max. Part No. 225088-3— A .123 Dia. [3.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Coaxial Contacts (Continued) Subminiature Coax, Size 16 Precision Formed, Crimp (Continued) Selection Chart for Twisted Pair and Shielded Wire Wire Size AWG mm2 Contact Finish Loose Piece Contact No. Pin Socket Ferrule Part No. Finish 30 0.05 (Twisted Pair, Solid) Related Product Data Application Tooling—Pages 76-79 28 0.08-0.09 (Twisted Pair, Solid) 28 0.08-0.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Contact Arrangements, Series 1 .093 .093 [2.36] [2.36] .185 .000 .185 [4.7] [4.7] Shell Sizes 11 and 13 .110 .110 [2.79] .000 [2.79] 1 .150 .150 [3.81] .000 [3.81] 2 .160 [4.06] .150 [3.81] CPC Series 1 .110 [2.79] 3 5 .000 .000 .000 6 .110 [2.79] 7 .150 [3.81] .160 [4.06] .155 [3.94] Arrangement 13-7 Max. Wire Ins. Dia. = .100 [2.54] Arrangement 11-4 Max. Wire Ins. Dia. = .
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Component Dimensions, Series 1 Square Flange Receptacle G ±.025 [±0.64] F ±.010 [±0.25] Panel Thk. .125 [3.18] Max. F ±.010 [±0.25] E Max. CPC Series 1 D ±.010 [±0.25] J Dia. +.007 *H –.000 Dia. [+0.18] Thread Size (See chart) Panel Cutout A Max. B ±.015 [±0.38] C ±.010 [±0.25] Free-Hanging Receptacle A Max. B ±.015 [±0.38] C ±.010 [±0.25] D ±.010 [±0.25] E Max. L Max. K Max.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Circular Plastic Connectors, Series 2 CPC Connectors, Series 2 for Cable or Panel Mount Square Flange Receptacle *G ±.035 [±0.64] (Accepts Size 20 DM or DF Crimp, Snap-In Contacts) *F ±.010 [±0.25] Panel Thk. .125 [3.18] Max. *J Dia. *F ±.010 [±0.25] *E Max. *D ±.010 [±0.25] +.007 *H –.000 Dia. [+0.18] *Thread Size (See chart) *A Max. Panel Cutout *B ±.015 [±0.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connectors, Series 2 (Continued) Receptacles, Printed Circuit Board Mount with .025 [0.64] sq. solder tails A B Housing—Thermoplastic, 94V-0 rated, black Contacts— A—Duplex plated gold flash on entire contact with .000030 [0.00076] min. gold on contact engagement area, tin on the termination area, all over .000050 [0.00127] min.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connectors, Series 2 (Continued) Special CPC Connectors, Series 2 Square Flange Feed-Thru Receptacles (with Permanently Sealed .040 [1.02] Dia. Solid Pins) (Pressure rated up to 30 psi) E ±.025 [±0.64] Panel Thk. .125 Max. [3.18] G Dia. D ±.010 [±0.25] B ±.010 [±0.25] D ±.010 [±0.25] Pin Both Sides +.007 F –.000 Dia. [+0.18] C Panel Cutout A Max.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Signal Contacts With Insulation Support Size 20 DF, Precision Formed, Crimp Contacts .085 Dia. [2.16] Max. Contact Size—20 Pin Diameter—.040 [1.02] *Test Current—7.5 ampere (Single contact, free-air test current; not to be construed as contact rating current. Use only for testing.) .390 [9.91] .575 [14.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Signal Contacts (Continued) Size 20 DM, Screw-Machined, Crimp Contacts Pin Diameter—.040 [1.02] Test Current*—7.5 amperes (Single contact, free-air test current; not to be construed as contact rating current. Use only for testing.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Contact Arrangements, Series 2 Note: Contact arrangements shown are of pin mating face (plug or receptacle). Socket mating face is mirror image. Shell Size 11 .062 .062 [1.57] [1.57] .124 [3.15] .000 .124 [3.15] .124 [3.15] .141 [3.58] .033 [0.84] .000 .091 [2.31] [.334 Dia. [8.48] 45° Arrangement 11-8 Max. Wire Ins. Dia. = .068 [1.73] Arrangement 11-9 Max. Wire Ins. Dia. = .068 [1.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Component Dimensions, Series 2 Square Flange Receptacle G ±.025 [±0.64] F ±.010 [±0.25] Panel Thk. .125 [3.18] Max. J Dia. F ±.010 [±0.25] E Max. D ±.010 [±0.25] +.007 *H –.000 Dia. [+0.18] Thread Size (See chart) A Max. Panel Cutout CPC Series 2 B ±.015 [±0.38] C ±.010 [±0.25] Free-Hanging Receptacle D ±.010 [±0.25] L Max. E Max. Thread Size (See chart) B ±.015 [±0.38] A Max.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connectors, Series 3 CPC Connectors, Series 3 Square Flange Receptacle *G ±.025 [±0.64] ±.010 Panel Thk. .125 [3.18] Max. *J Dia. *F [±0.25] *F ±.010 [±0.25] *E Max. *D ±.010 [±0.25] +.007 *H –.000 Dia. [+0.18] Panel Cutout *Thread Size (See chart) Listed part numbers are for connectors only; contacts must be ordered separately. *A Max. *B ±.015 [±0.38] *C ±.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Power Contacts, Series 3 Type XII, Precision Formed, Crimp .615 [15.62] Material .230 Max. [5.84] Copper Finish .978 Ref. [24.84] A—Tin B—.000030 [0.00076] selective gold over .000030 [0.00076] nickel C—.000100 [0.00254] silver plated contacts with lubricant added .230 Max. [5.84] Male Silver or Gold—35 amperes ‡ Tin—15 amperes ‡ Male .637 [16.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Power Contacts, Series 3 (Continued) Material High Current Type XII Crimp Contacts High Current Type XII Pin Part No. 193991-4 High Current Type XII Socket Finish Body — Silver Louvertac Band — Gold Part No. 193990-2 Extraction Tool Part No.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Component Dimensions, Series 3 Square Flange Receptacle G ±.025 [±0.64] Panel Thk. .125 [3.18] Max. D ±.010 [±0.25] F ±.010 [±0.25] J Dia. F ±.010 [±0.25] E Max. +.007 *H –.000 Dia. [+0.18] Thread Size (See chart) Panel Cutout A Max. Free-Hanging Receptacle B ±.015 [±0.38] C ±.010 [±0.25] CPC Series 3 Free Hanging Receptacle A Max. B ±.015 [±0.38] C ±.010 [±0.25] E Max. D ±.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Circular Plastic Connectors, Series 4 CPC Connectors, Series 4, Standard Sex Square Flange Receptacle (Accepts Type XII Male and Multimate pin contacts) 1.750±.025 [44.45±0.64] 1.438±.010 [36.53±0.25] Panel Thk. .125 [3.18] Max. 1.610 [40.89] Max. 1.510 Max. [38.35] Max. 1.438±.010 [36.53±0.25] 1.438±.010 [36.53±0.25] +.007 .150 –.000 Dia. [3.81+0.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. CPC Connector Accessories Cable Clamps Standard Size Cable clamps provide strain relief and can be used on all series receptacles and plugs. Clamping Insert Clamping Insert Plug (See Note 3) A ±.025 [±0.64] Dia. Material Black thermoplastic heat-stabilized, fire-resistant, self-extinguishing, UL 94V-0 rated Cable Clamp B ±.030 [±0.76] Dimensions A B Shell Size 11 13 17 23 .825 20.96 .
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications CPC Connector Accessories (Continued) Clamping Insert Self-Centering Cable Clamp (for Shell Size 23) The self-centering cable clamp is used in applications where strain relief protection is required and the cable or wire bundle is large and/or stiff. 1.600±.015 Dia. [40.64±0.38] Dia. Adjustable Clamping Area (See Note 1) Intermediate 1.663±.030 [42.24±0.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications CPC Connector Accessories (Continued) Back-Shell Extender (for Shell Size 23) A back-shell extender is used with a cable clamp in applications where added length and/or additional wire breakout are required. 1.620 [41.15] Dia. Max. 1.200±.015 [30.48±0.38] Material 1.450 Max. [36.83] Max. Black glass-filled thermoplastic Part No.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. CPC Connector Accessories (Continued) Flexible Cable Boot and Internal Cable Grip (for Shell Size 11) Flexible cable boots, with internal cable grip installed, provide strain relief capabilities for jacketed cable in applications where aesthetic appearance is essential. They can be threaded onto plugs or receptacles. .265 [6.73] Dia. .850 [21.59] Dia. 2.750±.031 [69.85±0.79] .265 [6.73] Dia.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications CPC Connector Accessories (Continued) Keying Plugs Keying plugs are used to provide keying capabilities for all connector series. Keying plugs are used in socket cavities of standard sex plugs and reverse sex receptacles, except when used with sealing caps. 1.000 [25.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications One-Piece Sealed Circular Plastic Connectors, Series 1 Sealed CPC Receptacles, Special Series 1 with Pre-Installed, Bonded Peripheral Seal Square Flange Receptacle (Uses Flange Seal Part No. 81665-■ on page 51) 1.705 Max. [43.31] .094±.010 [2.39±0.25] 1.125±.025 [28.58±0.64] .420±.015 [10.67±0.38 .844±.010 Typ. [21.44±0.25] 1.750±.025 [44.45±0.64] .844±.010 [21.44±0.25] .687±.010 Dia. [17.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. One-Piece Sealed Circular Plastic Connectors, Series 5 CPC Connectors, Series 5 Sealed – Reverse Sex Square Flange Receptacle (Uses Flange Seal Part No. 81665-2 on page 51) 1.125±.010 [28.58±0.25] 1.050 [26.67] Dia. 1.435 [36.45] 1.125±.010 [28.58±0.25] Listed part numbers are for connectors only; contacts must be ordered separately. 1.105 [28.07] Dia. Max. .094 [2.39] .514 [13.06] 1.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Sealed Circular Plastic Connectors Multimate Size 16 Contacts Precision formed signal/low current Pin Diameter—.062 [1.57] Test Current—13 amps max. .125 POWERBAND Contacts Precision formed high current Pin Diameter—.125 [3.175] Test Current—50 amps max.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Two-Piece Sealed Circular Plastic Connectors, Series 5 CPC Connectors, Series 5 Sealed – Reverse Sex Square Flange Receptacle (Uses Flange Seal Part No. 81665-2 on page 51) 1.435±.015 [36.45±0.38] 1.125±.010 [28.58±0.25] Typ. .420 [10.67] .280±.010 [7.11±0.25] 1.050 [26.67] Dia. 1.090±0.15 [27.69±0.38] Dia. 1.435±.015 [36.45±0.38] 1.125±.010 [28.58±0.25] Typ.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Two-Piece Sealed Circular Plastic Connectors, Series 6 CPC Connectors, Series 6 Sealed – Reverse Sex Square Flange Receptacle (Uses Flange Seal Part No. 81665-2 on page 51) 1.435±.015 [36.45±0.38] 1.125±.010 [28.58±0.25] Typ. .280 [7.11] .420 [10.67] 1.435±.015 [36.45±0.38] 1.090 Dia. [27.69] 1.125±.010 [28.58±0.25] Typ.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Two-Piece Sealed Circular Plastic Connectors, Special Series 1 Sealed CPC Receptacles, Special Series 1 with Pre-Installed, Bonded Peripheral Seal Square Flange Receptacle (Uses Flange Seal Part No. 81665- ■ on page 51) E 4 Plc. B A Recommended Panel Cutout Free-Hanging Receptacle Listed part numbers are for connectors only; contacts must be ordered separately.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Two-Piece Circular Plastic Connector Sealing Accessories Wire Entry Seal Kits for Plug and Receptacle Housings ±.010 A [±0.254] Dia. Material and Finish .075 [1.94] Seal—Silicon, black Pressure Plate—Nylon, black .250±.010 [6.35±0.25] Dia. Seal Dimension A .681 17.30 .790 20.07 Kit for Pins Kit for Sockets 213926-1 213925-1 213899-1 213899-1 .790 20.07 213900-1 213900-1 .790 20.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Circular Plastic Connector Sealing Accessories A Sealing Caps for Receptacles only B ±.015 [±0.38] Sealing caps are used to protect exposed contacts of unmated receptacles. 3.000±.030 [76.2±0.76] .143 Dia. [3.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Circular Plastic Connector Sealing Accesories (Continued) Jacketed Cable Seals (for Shell Size 23) 3.500±.030 [88.9±0.76] A jacketed cable seal kit provides an environmentally sealed connection for jacketed cable. +.000 1.095 [27.81] Dia. 1.290–0.15 [32.77–0.38] Dia.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Engineering Notes 55 Catalog 82021 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 52-55-1106-0800 C.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. MIL-C-5015 Style Circular Plastic Connectors (CPC), Shell Size 20-14 Plug Kit, Unassembled 5-20 Self Tapping Screw, Quantity 2 Reverse Sex (Accepts pins) Part Number 213571-2 without Cable Clamp .625 [15.88] Standard Sex (Accepts sockets) Part Number 213652-1 without Cable Clamp 2.839±.040 [72.11±1.02] Clamping Inserts .703 [17.86] Max. Outside Dia.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. MIL-C-5015 Style Circular Plastic Connectors (CPC), Shell Size 18-10 Plug Kit, Unassembled 1.174±.010 [29.82±0.25] 1.620±.010 [41.15±0.38] .560 [14.22] Reverse Sex (Accepts pins) Part Number 213671-1 without Cable Clamp 1.435±.010 [36.45±0.25] Dia. .925±.003 [23.50±0.08] Dia.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Engineering Notes 59 Catalog 82021 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 52-55-1106-0800 C.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Metal-Shell Circular Plastic Connectors, Series 1 Metal-Shell CPC Connectors, Series 1, Standard Sex Square Flange Receptacles (Accepts Multimate Pins) F Mating Face E D Listed part numbers are for connectors only; contacts must be ordered separately. .975±.010 [24.77±0.03] 2 Plc.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Metal-Shell Circular Plastic Connectors, Series 1 (Continued) Metal-Shell CPC Connectors, Series 1, Reverse Sex Square Flange Receptacles (Accepts Multimate Sockets) F Mating Face E D B Listed part numbers are for connectors only; contacts must be ordered separately.
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Metal-Shell CPC Connectors, Series 1, Contact Arrangements Shell Size 14 .170 .170 [4.32] .000 [4.32] .094 .094 [2.39] [2.39] .172 .172 [4.37] .000 [4.37] .086 .086 [2.18] [2.18] .130 [3.3] .126 [3.2] .047 [1.19] .000 .000 .126 [3.2] .130 [3.3] Arrangement 14-5 Max. Wire Ins. Dia. = .150 [3.81] Shell Size 22 Arrangement 14-7 Max. Wire Ins. Dia. = .100 [2.54] .000 .193 .043 .032 .
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Metal-Shell Circular Plastic Connectors, Series 2 Metal-Shell CPC Connectors, Series 2, Standard Sex Square Flange Receptacles (Accepts 20 DF and 20 DM Pins) F A E B D Listed part numbers are for connectors only; contacts must be ordered separately.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Metal-Shell Circular Plastic Connectors, Series 2 (Continued) Metal-Shell CPC Connectors, Series 2, Reverse Sex Square Flange Receptacles (Accepts 20 DF and 20 DM Sockets) A Mating Face E F D Listed part numbers are for connectors only; contacts must be ordered separately.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Metal-Shell CPC Connectors, Series 2, Contact Arrangements Shell Size 22 .248 .124 .000 .124 .248 [6.3] [3.15] [3.15] [6.3] .310 .186 .062 .062 .186 .310 [7.87] [4.72] [1.57] [1.57] [4.72] [7.87] .294 [7.47] .170 [4.32] .062 [1.57] .000 .062 [1.57] .170 [4.32] .124 [3.15] .294 [7.47] Arrangement 22-28 Max. Wire Ins. Dia. = .068 [1.73] Shell Size 28 .434 .310 .186 .062 .062 .186 .310 .
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Metal-Shell Circular Plastic Connectors, Series 3 Square Flange Receptacles (Accepts Type XII Male Pins) Metal-Shell CPC Connectors, Series 3, Standard Sex F A E B D Listed part numbers are for connectors only; contacts must be ordered separately.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Metal-Shell Circular Plastic Connectors, Series 3 (Continued) Metal-Shell CPC Connectors, Series 3, Reverse Sex Square Flange Receptacles (Accepts Type XII Female Sockets) F A E B D Listed part numbers are for connectors only; contacts must be ordered separately.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Metal-Shell CPC Connectors, Series 3, Contact Arrangements Shell Size 22 .148 [3.76] .000 .148 [3.76] .107 [2.72] .000 .213 [5.41] Arrangement 22-3 Max. Wire Ins. Dia. = .220 [5.59] Shell Size 28 .343 [8.71] .172 .000 [4.37] .172 .343 [4.37] [8.71] .296 [7.52] .000 Metal-Shell CPC Series 3 .296 [7.52] Arrangement 28-7 Max. Wire Ins. Dia. = .220 [5.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Metal-Shell Circular Plastic Connectors, Series 4 Metal-Shell CPC Connectors, Series 4 Square Flange Receptacles (Standard Sex Receptacles accept Type XII Male and Multimate Pins. Reverse Sex Receptacles accept Type XII Female and Multimate Sockets.) F A E B D Listed part numbers are for connectors only; contacts must be ordered separately.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Metal-Shell CPC Connectors, Series 4, Contact Arrangements Shell Size 28 .276 .092 .092 .276 [7.01][2.34][2.34][7.01] .400 .184 .184 .400 [10.16][4.67].000 [4.67] [10.16] .400 [10.16] .316 [8.03] .158 [4.01] .000 .158 [4.01] .316 [8.03] .400 [10.16] Arrangement 28-16M Max. Wire Ins. Dia. = .150 [3.81] for Multimate Contacts, .220 [5.59] for Power Contacts .364 .182 .182 .364 [9.25][4.62].
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Metal-Shell CPC Connectors Component Dimensions Thread-Size: 7/8-20 UNEF-2A (Shell Size 14) 15/16-20 UNEF-2A (Shell Size 22) 1-3/8-18 UNEF-2A (Shell Size 28) Square Flange Receptacles F ±.015 [±0.38] E ±.005 [±0.13] J ±.005 [±0.13] Dia. E ±.005 [±0.13] G ±.010 [±0.25] Dia. Panel Cutout, Front Mounted Receptacle D Max. J ±.005 [±0.13] Dia. E ±.005 [±0.13] H Dia. Front and Rear Panel Thk. .
Note: All part numbers are RoHS Compliant. AMP Circular Connectors for Commercial Signal and Power Applications Metal-Shell CPC Connector Accessories Internal Threads Cable Clamps Material and Finish A Body and Clamp Halves—Zinc alloy, nickel plated Screws and Washers—Stainless steel Screw with Lock Washer (Two Supplied) ±.031 [±0.79] Clamp Half (Two Supplied) Cable Clamp Body B ±.031 [±0.79] C ±.031 [±0.79] Plug (Shown for reference only) Cable Dia. Range Shell Size 14 22 28 A .938 23.83 .
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Engineering Notes 74 Catalog 82021 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 52-55-1106-0800 C.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Miniature Circular Plastic Connectors (CPC) (Continued) Shell Size 8 (4 Position shown) Receptacle Assembly, Panel Mount (Order pin contacts separately — see page 75) 1.142 [29.00] .555 [14.10] Alignment Indicator .827 [21.00] White Alignment Dot 1/2-20 UNF-2A 5/8-24 UNEF-2A Thread Jam Nut shown for reference only. Must be ordered separately. Flange Seal shown for reference only.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Miniature Circular Plastic Connectors (CPC) (Continued) Shell Size 11 (9 Position shown) Plug Assembly (Order socket contacts separately — see page 75) Receptacle Assembly, Panel-Mount (Order pin contacts separately — see page 75) .689 [17.50] 1.14 ± .010 [29.00 ± 0.25] Jam Nut & Flange Seal shown for reference only. Must be ordered separately. .413 [10.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Miniature Circular Plastic Connectors (CPC) (Continued) Contacts and Application Tooling Pin (for Receptacles) Contact Part Numbers Wire Size Range AWG [mm2] Ins. Dia. Range 30-26 [.05-.12] .035-.050 .889-1.27 26-22 [.12-.3] .047-.069 1.19-1.75 22-18 [.3-.8] or 22 x (2) [.3] .059-.094 1.50-2.39 or .067 x (2) 3.38 .671 [17.04] Socket (for Plugs) .659 [16.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Application Tooling Mechanical Hand Tools for Interchangeable Die Sets SDE (Standard Die Envelope) Die Sets SDE die sets provide costeffective flexibility, through many options for a common die-set outline. The SDE die sets can be adapted for use with CERTI-CRIMP hand tools, PRO-CRIMPER III hand tools, the SDE Terminator and the 626 Pneumatic Tool System.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Application Tooling (Continued) Crimp Machines Semiautomatic bench machines for crimping reeled terminals and contacts, featuring a quiet and reliable direct motor drive, microprocessor controls for ease of setup and operation, and guarding and lighting designed for operator convenience and safety. All models are equipped with either manual or automatic precision adjustment of crimp height.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Application Tooling (Continued) Lead Makers This fully-automatic, PCcontrolled leadmaker can be equipped with up to three processing stations enabling the crimping of both ends of the wire, double-crimp connections with three different contacts, singleended seal applications, tinning or ink-jet marking.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Application Tooling (Continued) Side-Feed Heavy-Duty Miniature Applicators (coded HDM) Interchangeable applicators for crimping products reeled side-by-side on single or dual carrier strips (primarily closed-barrel terminals and open-barrel contacts). Similar design as the end-feed version.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Technical Documents Various technical documents are available for your use: Product Specifications describe technical performance characteristics and verification tests. They are intended for the Design, Component and Quality Engineer.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant. Part Number Index Note: This part number index lists all cataloged parts by base number only. Complete part numbers (with prefixes and/or suffixes) are shown on the pages indicated.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant.
AMP Circular Connectors for Commercial Signal and Power Applications Note: All part numbers are RoHS Compliant.
Circular Connectors for Commercial Signal and Power Applications Global Contacts Americas Argentina – Buenos Aires Phone: +54-11-4733-2200 Fax: +54-11-4733-2211 Brasil – São Paulo Phone: +55-11-3611-1311 Fax: +55-11-3611-0397 Canada – Toronto Phone: +905-475-6222 Fax: +905-474-5520 Product Information Center: (Technical Support) Phone: +905-470-4425 Fax: +905-474-5525 Colombia – Bogota Phone: +57-1-231-9398 Fax: +57-1-660-0206 Mexico – Mexico City Phone: +52-55-1106-0800 +01-800-733-8926 Fax: +52-55-110
Tyco Electronics Corporation Harrisburg, PA tycoelectronics.com 82021-XXX-MS-FP-Rev.
