Models H62 & H63 Shake/Slush Freezers Original Operating Instructions 067343--M 4/1/09 (Original Publication) (Updated 4/16/12)
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: A E April, 2009 Taylor All rights reserved. 067343--M The word Taylor and the Crown design are registered trademarks in the United States of America and certain other countries. Taylor Company 750 N. Blackhawk Blvd.
Table of Contents To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents -- Page 2 Daily Opening Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining Product From The Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 1 To the Installer The following are general installation instructions. For complete installation details, please see the check out card. Note: All repairs must be performed by an authorized Taylor Service Technician. Installer Safety This unit has many sharp edges that can cause severe injuries. In all areas of the world, equipment should be installed in accordance with existing local codes. Please contact your local authorities if you have any questions.
Air Cooled Units Electrical Connections DO NOT obstruct air intake and discharge openings: In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA 70-1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity. This code contains provisions considered necessary for safety.
Refrigerant S S S Stationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation.
Section 2 To the Operator The Models H62 and H63 shake freezers have been carefully engineered and manufactured to give you dependable operation. These units, when properly operated and cared for, will produce a consistent, quality product. Like all mechanical products, they will require cleaning and maintenance. A minimum amount of care is necessary if the operating procedures outlined in this manual are followed closely.
Section 3 Safety We, at Taylor Company, are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built--in safety features to protect both you and the service technician. As an example, warning labels have been attached to the freezer to further point out safety precautions to the operator. S DO NOT operate the freezer unless it is properly grounded.
DO NOT draw product or attempt to disassemble the unit during the HEAT cycle. The product is hot and under extreme pressure. DO NOT allow untrained personnel to operate this machine. S DO NOT operate the freezer unless all service panels and access doors are restrained with screws. S DO NOT remove any internal operating parts (examples: freezer door, beater, scraper blades, etc.) unless all control switches are in the OFF position.
Section 4 Operator Parts Identification H62 Exploded View Figure 1 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 KIT A.-COVER-HOPPER X65368 10 GASKET-BASE PAN 067316 2 SPACER-PROBE *SQ HOLE* 030966 11 SHELF-TRAY-DRIP 056076 3 DISC-PROBE *SQ HOLE* 030965 12 PANEL A.-FRONT-LOWER X69419 4 PROBE A.-MIX LOW-HT X42077 13 SHIELD-SPLASH 049203 5 BLADE A.
H63 Exploded View Figure 2 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 KIT A.-COVER-HOPPER X65369 10 PANEL-SERVICE 048380 2 BLADE A.-AGITATOR X56591-SP1 11 TRAY-DRIP 14.8 046275 3 TRIM-REAR CORNER 046668 12 046177 4 PANEL A.-DUCT-RIGHT X67958-SP1 SHIELD-SPLASH-WIRE 13-11/16 L 5 PANEL-REAR W/LOUVERS 026980-SP 13 PAN-DRIP 19-1/2 LONG 035034 6 ADAPTOR A.-CASTER X18915 14 STUD-NOSE CONE 5/16-18X3/8-1 011390 7 CASTER-SWV 5/8 STEM 4IN 018794 15 PANEL A.
Door and Beater Assembly Figure 3 ITEM DESCRIPTION PART NO. ITEM 1 VALVE A.--DRAW X56119 9 2 O--RING--1--1/16 OD X .139W 020571 3 O--RING 5/8 OD X .103 W 4 NUT--STUD 5 DESCRIPTION PART NO. TORQUE A.--SOFT SLUSH X67190 10 BEARING--GUIDE 014496 016030 11 GASKET--DOOR 5.177 ID 016672 021508 12 BEARING--FRONT 013116 PLUG--PRIME 067192 13 BEATER A.--7QT BLADELESS X45719 6 DOOR A.--1 SPOUT X67194--SER SHAFT--BEATER H62 067489 7 O--RING--.291 ID X .
Accessories Figure 4 ITEM DESCRIPTION PART NO. 1 BRUSH-MIX PUMP BODY 3” X 7” WHITE 023316 2 BRUSH-END-DOOR-SPOUT 039719 3 BRUSH-DOUBLE ENDED 013072 4 BRUSH-REAR BRG 1IN.D X 2IN 013071 5 BRUSH-DRAW VALVE 014753 ITEM DESCRIPTION PART NO. 6 LUBRICANT-TAYLOR HI PERF 048232 7 PAIL-MIX 10 QT. 013163 8 TRAY-PARTS-BARREL 7 QT. 067406 * KIT A.-TUNE UP X67224 SANITIZER·STERA SHEEN SEE NOTE ** *Not Shown **Note: A sample container of sanitizer is sent with the unit.
Section 5 Important: To the Operator H62 Figure 5 ITEM DESCRIPTION ITEM 1 2 3 4 5 POWER SWITCH (TOGGLE) LED INDICATOR--MIX LOW (PCB A--LED) LED INDICATOR--MIX OUT (PCB A--LED) LED INDICATOR--HEAT MODE LIQUID CRYSTAL DISPLAY 6 7 8 9 DESCRIPTION LED INDICATOR-- CLEAN MANUALLY CONSISTENCY CONTROL (SWITCH--TORQUE) KEYPADS COVER--VISCOSITY ADJUSTMENT 120206 Models H62 & H63 11 Important: To the Operator
H63 Figure 6 ITEM DESCRIPTION 1 2 3 4 5 6 7 POWER SWITCH (TOGGLE) LIQUID CRYSTAL DISPLAY LED INDICATOR--MIX LOW (PCB A--LED) LED INDICATOR--MIX OUT (PCB A--LED) LED INDICATOR--HEAT MODE LED INDICATOR--CLEAN MANUALLY CONSISTENCY CONTROL (SWITCH--TORQUE) COVER--VISCOSITY ADJUSTMENT 8 The following chart identifies the symbol definitions used on the operator switches.
Power Switch LED Indicator - CLEAN MANUALLY The CLEAN MANUALLY indicator flashes to indicate that the freezer must be disassembled and brush cleaned within 24 hours. When placed in the ON position, the power switch allows control panel operation. The power switch is located on the left side of the control channel. When all four indicators are flashing, the freezer is in a locked condition.
Operating Screen Descriptions If any of the requirements for a brush clean have not been met, the time displayed will remain at 5:00 minutes. When all the requirements for a brush cleaning are met, and the five minutes expire, the screen will change to the second screen, which is the standard power switch OFF screen. When the machine is powered the system will initialize. The screen will display “INITIALIZING”.
When the heating phase is complete, the freezer goes into the holding phase of the cycle. The holding phase will hold the temperature above 151_F (66.1_C) for a minimum of 30 minutes. The following displays pertain to the HEAT cycle: A System Alert screen displays an alert and alarm 15 minutes prior to the start of the heat cycle. The alarm will sound and show on the display. The alarm will sound until the SEL key is pressed to clear the fault.
Freezer Locks The next display is the screen which will appear after the failure message. To comply with health codes, heat treatment system freezers must complete a heat treatment cycle daily, and must also be brush cleaned every 14 days. Brush cleaning is the normal disassembly and cleaning procedures. Failure to follow these guidelines will cause the control to lock the freezer out of the AUTO mode. There are two types of freezer lock conditions that can occur: Hard Lock or Soft Lock.
Following are the variable messages which will appear on line 3: 1. POWER SWITCH OFF: Power switch was in the OFF position. 2. MIX OUT PRESENT: There was a mix out condition present. 3. AUTO OR STANDBY OFF: The unit was not in the AUTO or STANDBY mode. 4. NO HEAT CYCLE TRIED: A heat treatment cycle was not attempted in the last 24 hours. (AUTO HEAT TIME was advanced, or a power loss was experienced at the time the cycle was to occur, or a heat cycle failure not due to a thermistor failure.
Clearing Fault Tones 9. To clear the tone for any faults which have been corrected, press the <-- -- arrow key. To see if there is more than one fault, press the MENU/SEL key. When the last fault is displayed, the control will return to the OPERATOR MENU. To return to the main screen, move the cursor to “A” and press the MENU/SEL key again. 10. NO FAULT FOUND: There was no fault found in the freezer. Nothing will appear on the screen after this variable message appears. 2.
the MENU/SEL key while under “ENABLE” will accept the selection and will automatically increase the clock one hour at 2:00 a.m. on the first Sunday in every April. It will decrease one hour at 2:00 a.m. on the last Sunday in every October. Pressing the MENU/SEL key while under “DISABLE” will accept the selection and operate normally. Pressing the MENU/SEL key again will accept the selection and return to the OPERATOR MENU. Screen “E” is AUTO HEAT TIME.
Screen “H” is HEAT CYCLE DATA. The information from the previous heat treatment cycles can be obtained through this screen. The most recent heat treatment cycle data will be shown first; press the plus key to scroll through the remaining heat cycle displays. If a heat treatment cycle failure should occur, a two character message will appear on the second line of the screen. Press the MENU/SEL key once to return to the OPERATOR MENU. 00:00 00:00 HEAT OVER 00:00 00:00 TEMP AT END 00:00 COOL 00:00 0.
Screen “L” is AUTO START TIME. This option allows the manager to set the time of day that the machine automatically enters the AUTO mode from the STANDBY mode. Selecting this option displays the AUTO START TIME Enable/Disable screen. Pressing the <---- key moves the cursor under the ENABLE screen. Pressing the ----> key moves the cursor under the DISABLE selection. AUTO START TIME ENABLE Screen “M” is MIX LEVEL AUDIBLE. This option enables or disables an audible alarm for MIX LOW and MIX OUT conditions.
Section 6 Operating Procedures The Models H62 and H63 have 7 quart (6.6 liter) freezing cylinders and offer one flavor. The Model H63 has been selected to show you the pictured step--by--step operating procedures for both models contained in this manual. These models, for practical purposes of operation, are the same. We begin our instructions at the point where we enter the store in the morning and find the parts disassembled and laid out to air dry from the previous night’s brush cleaning.
Step 3 Slide the beater into the freezing cylinder. Step 5 Assemble the torque rotor by sliding the two o--rings on the front of the shaft and lubricate them thoroughly to prevent leaking. Place the white plastic guide bearing on the rear of the rotor shaft. DO NOT lubricate the plastic guide bearing. Figure 9 Step 4 Make sure the beater assembly is in position over the drive shaft. Turn the beater slightly to be certain that the beater is properly seated.
Step 9 Place the o--ring on the prime plug and lubricate. Step 7 Slide the two o--rings onto the draw valve and lubricate. Figure 15 Step 10 Screw the prime plug into position on the front of the door. Figure 13 Step 8 Lubricate the inside of the door spout, top and bottom. Insert the draw valve into the freezer door from the top. It will be necessary to rotate the draw valve bracket to the right to allow installation of door on freezer.
Step 12 Install the freezer door. Locate the torque rotor in the center hole of the freezer door. Position the door on the four studs on the front of the freezing cylinder and firmly push it into place. Install the four handscrews on the studs and finger--tighten equally in a criss--cross pattern to insure the door is snug. Do not over--tighten. Step 15 Install the torque arm.
Step 17 Lay the agitator in the bottom of the mix hopper for sanitizing. Step 5 Press the WASH key and allow the sanitizing solution in the freezing cylinder to agitate for five minutes. Figure 21 Sanitizing Step 1 Prepare a pail of an approved 100 PPM sanitizing solution (examples: 2--1/2 gal. [9.5 liters] of Kay--5R or 2 gal. [7.6 liters] of Stera--SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.
Priming Step 7 Once the sanitizer stops flowing from the dispensing spout, close the draw valve and press the WASH key, cancelling the beater motor operation. Note: If a powdered or concentrated mix will be used, follow the manufacturer’s mix preparation instructions before placing the mix in the mix hopper. DO NOT attempt to mix the product in the hopper! Step 1 Place a mix pail beneath the door spout and open the draw valve. Fill the hopper with FRESH mix and allow it to flow into the freezing cylinder.
Step 4 Fill the hopper with fresh mix and place the mix hopper cover in position. Step 1 Remove the hopper cover and the agitator. Take these parts to the sink for further cleaning and sanitizing. Note: Use only FRESH mix when priming the freezer. Note: Pressing the <-- -- arrow key will stop the agitator rotation for ten seconds.
Daily Opening Procedures Step 7 Return to the freezer with a small amount of cleaning solution. Dip the end brush into the cleaning solution and brush clean the door spout and bottom of the draw valve. Evaluate the condition of LED’s (lights) and screen messages (Hard Lock or Soft Lock, etc.) before performing the Opening Procedures. As indicated in the illustration below, four flashing LED’s indicate a “locked” condition.
Step 8 Press the AUTO key to resume normal operation. When the unit cycles off, product is ready to serve. DO NOT use a water jet to clean or rinse the freezer. Failure to follow these instructions may result in serious electrical shock. Step 5 Return to the freezer with a small amount of sanitizing solution. Dip the end brush into the sanitizing solution and brush clean the door spout and bottom of the draw valve.
Draining Product From The Freezing Cylinder Step 4 Open the draw valve and drain the remaining product from the freezing cylinder and mix hopper. Step 1 Press the AUTO key, cancelling compressor and beater motor operation. Figure 34 Figure 32 Step 5 When the flow of product stops, press the WASH key, cancelling the wash cycle and close the draw valve. Discard this product. Step 2 Remove the hopper cover and the agitator from the mix hopper. Take these parts to the sink for cleaning.
Rinsing Step 3 Open the draw valve on the freezer door. Drain all the rinse water from the door spout, close the draw valve, and press the WASH key cancelling the wash cycle. Step 1 Pour two gallons (7.6 liters) of cool, clean water into the mix hopper. With the brushes provided, scrub the mix hopper, mix level sensing probes, the outside of the agitator housing, and the mix inlet hole. Figure 38 Repeat this procedure until the rinse water being drawn from the freezing cylinder is clear.
Disassembly Step 4 Press the WASH key and allow the cleaning solution in the freezing cylinder to agitate for five minutes. Note: Failure to remove parts, brush clean and then air dry these parts, will result in damage to the related parts. These parts must be removed every 14 days or the machine will lock--out and will not operate in the AUTO mode. BE SURE THE POWER SWITCH IS IN THE OFF POSITION. Failure to do so may cause injury from electrocution or hazardous moving parts.
Brush Cleaning Step 3 Return to the freezer with a small amount of cleaning solution. With the black bristle brush, brush clean the rear shell bearing at the back of the freezing cylinder. DO NOT use a water jet to clean or rinse the freezer. Failure to follow these instructions may result in serious electrical shock. Step 1 Prepare a sink with an approved cleaning solution (examples: Kay--5R or Stera--SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.
Section 7 Important: Operator Checklist During Cleaning and Sanitizing Regular Maintenance Checks j 1. Rotate the scraper blades to allow both sides of the knife edge to wear evenly. This will contribute to self--sharpening and help maintain fast, efficient freezing. Cleaning and sanitizing schedules are governed by your State or local regulatory agencies and must be followed accordingly. The following check points should be stressed during the cleaning and sanitizing operations.
Winter Storage Disconnect the freezer from the main power source to prevent possible electrical damage. If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is subject to freezing conditions. Your local Taylor Distributor can perform this service for you.
Section 8 PROBLEM 1. Soft lock message appears on LCD. Models H62 & H63 Troubleshooting Guide PROBABLE CAUSE PAGE REF. REMEDY a. More than 24 hours since the last heat cycle. a. The freezer must go through a heat cycle every 24 hours. The freezer must now be disassembled and brush cleaned or placed in a heat cycle. 17 b. The power switch is in the OFF position. b. The power switch must be in the ON position. The freezer must now be disassembled and brush cleaned or placed in a heat cycle. 17 c.
PROBLEM 2. Hard lock message appears on LCD. 3. No product being dispensed with draw valve open and machine in the AUTO mode. 4. The product is too stiff. PAGE REF. PROBABLE CAUSE REMEDY a. There has been a thermistor failure (freezing cylinder, hopper, or glycol) during the heat treatment process. a. The freezer must be disassembled and brush cleaned. 16 b. More than 14 days since last brush cleaning. b. The freezer must be disassembled and brush cleaned every 14 days. 16 a.
PROBLEM 5. The product is too soft. PROBABLE CAUSE PAGE REF. REMEDY a. Improper consistency control adjustment. a. Product should be dispensed at 27_ to 29_F. (-2.8_ to -1.7_C.). 13 b. The torque rotor is binding. b. Before installing the torque arm, check to see if the torque rotor can be rotated freely without binding. 23 c. Improper lubrication of torque rotor o-rings. c. Lubricate the o-rings properly. 24 d. Lubrication of torque rotor guide bearing. d. Do not lubricate the guide bearing.
PROBLEM 9. The freezing cylinder walls are scored. 10. Excessive mix leakage from the dispensing spout. 11. Excessive mix leakage into the rear drip pan. Troubleshooting Guide PROBABLE CAUSE PAGE REF. REMEDY a. The front bearing is missing or worn. a. Install or replace front bearing. b. The gear box is out of alignment. b. Call a service technician to realign gear box. ------ c. The beater pins are broken. c. Call service technician to repair or replace. 35 d. The beater assembly is bent.
PROBLEM 12. No freezer operation after placing unit in the AUTO mode. 13. Liquid Crystal Display is blank after power switch is placed in the ON position. 14. Product not feeding into freezing cylinder. Models H62 & H63 PROBABLE CAUSE PAGE REF. REMEDY a. Unit unplugged. a. Plug into wall receptacle. ------ b. Circuit breaker off or blown fuse. b. Turn circuit breaker on or replace fuse. ------ c. Beater motor out on reset. c. Clear the tone and reset freezer. 13 d.
Section 9 PART DESCRIPTION Parts Replacement Schedule EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY QTY.
ACCUMULATOR-COPPER 2"DIA 13" ADAPTOR A.-CASTER ADAPTOR-5/16 BARB-5/16FS ARMAFLEX 1/2 ID X 3/8WALL ARMAFLEX 3/8 ID X 1/4WALL ARM-TORQUE 5.813L SS BEARING-FRONT BEARING-GUIDE BEATER A.-7QT-BLADELESS BEATER A.-7QT-1 PIN-SUPPO +BLADE-SCRAPER-PLASTIC 9-1 +CLIP-SCRAPER BLADE 8.75 I BELT-V-4L420 BELT-V-4L370 BLADE A.-AGITATOR *C708* BLADE A.-AGITATOR *C708* BLADE-SCRAPER-PLASTIC 9-1 BLOCK-TERMINAL 2P L1,L2 - 1PH BLOCK-TERMINAL 3P L1,L2,L3 - 3PH BLOCK-TERMINAL 3P .25 SPA BLOCK-TERMINAL-PLUG 8P .
+ Available Separately Parts List 44 Models H62 & H63 040040-027 040040-044 040040-011 080071 057525 012906 500311 051785 041247-W5 018794 034081 047344 046238 066099 067952 001086 019481 001086 024420 051958-27 012906 033044-1 051957-27 051958-33 056944 019558 012721 052284-SP 046698 046699 038374 067368-27 067368-33 +CAPACITOR-RUN 20UF/440V +CAPACITOR-START 189-227UF/33 + RELAY-START-COMPRESSOR COMPRESSOR RS80C1E-TF5-224 CONDENSER-AC 16X16 3ROW 14FPI CONDENSER-AC 12LX18HX4.
+ Available Separately Models H62 & H63 45 Parts List DISPLAY-LIQUID CRYSTAL DOOR A.-PARTIAL-1 SPT +PLUG-PRIME *H63* +O-RING-5/8 OD X .103W +VALVE A.-DRAW *H63* +O-RING-1-1/16 OD X.139W +GASKET-DOOR 5.177ID X 5.9 DRYER-FILTER-HP62-3/8 X 1 EYELET-RESET BUTTON FAN-5 BLADE 12" PUSH 26DE FASTENER-CLIP 1/4-20 U-TY FASTENER-DOOR LATCH FASTENER-DOOR STRIKE FILTER A.-GLYCOL FILTER-INLINE-GLYCOL-40 MICRON FILTER A.-GLYCOL FILTER-INLINE-GLYCOL-40 MICRON FILTER-AIR-21.688X15.813H FILTER-AIR-18.00LX14.25HX.
+ Available Separately Parts List 46 Models H62 & H63 067405-33G 056884-33G 067363-27G 067363-27G 067365-33 059244 067391-G 056893 X47331-27 035786 067429-27 R502011 X80290-03 080071 056588 057342 057525 066937 050535-03 017395 056587 600165 006812 X56586-03J X65658 056771 065409 065471 X65368 045191 X65369 045191 INTERLOCK A.-DOOR SWITCH-REED*DOOR INTERLOCK*68" SPRING-INTERLOCK DOOR FITTING DOOR INTERLOCK KIT A.-COVER-HOPPER*SINGL LABEL-CAUTION-AGITATOR KIT A.
+ Available Separately Models H62 & H63 47 Parts List KIT A.-TUNE UP*0H63* BEARING-FRONT BEARING-GUIDE GASKET-DOOR 5.177ID X 5.938O O-RING-.291 ID X .080W O-RING-1-1/16 OD X.139W O-RING-5/8 OD X .
+ Available Separately Parts List 48 Models H62 & H63 O-RING-.291 ID X .080W PAIL-MIX 10 QT. PAN-DRIP 11-5/8 LONG PAN-DRIP 19-1/2 LONG PANEL A.-DUCT-RIGHT *0H62* PANEL A.-FRONT-LOWER *0H62* PANEL-FRONT-UPPER *0H62* PANEL-SIDE-LEFT *0H62* PANEL-REAR *0H62* PANEL A.-FRONT *H63* PANEL A.-DUCT-AIR *0H63* PANEL-SIDE *H60*LEFT PANEL-REAR W/LOUVERS *547 PANEL-SERVICE *H63* PCB A.-CONTROL *H62* BLADELESS CHIP-SOFTWARE *H62* BLADELESS CONTROL-ROHS-UVC2 PCB A.
+ Available Separately Models H62 & H63 49 Parts List PULLEY-AK74 X 5/8 PUMP-GLYCOL-1/8NPT-1650 RPM +ADAPTOR-1/8MP X 5/16 BARB-BR +BOOT-PUMP-GLYCOL +CLAMP-HOSE 35/64-STEPLESS EA +ELBOW-1/8P-STREET-BRASS +HOSE-RUBBER 5/16"ID X 9/16"OD RELAY-3 POLE-20A-208/240 50/60 RELAY-DPDT 100UA TO 7A 1/8HP RELAY-SPST-30 A-240 V RELAY-START-COMPRESSOR RING A.-AIR FLOW-COND.* SANITIZER-STERA SHEEN -GREEN SHAFT-BEATER *0H62* +SEAL-DRIVE SHAFT SHAFT-BEATER SHAFT-BEATER +SEAL-DRIVE SHAFT SHELF-TRAY-DRIP SHELL A.
+ Available Separately Parts List 50 Models H62 & H63 SWITCH A.-DRAW *H60* ARM A.-DRAW *H60* SWITCH-LEVER-SPDT-11A-125-27 PIN-PIVOT E-RING 3/16 .335 OD 1500-18P +KNOB-DRAW VALVE +NUT-LOCK KNOB SWITCH A.-REED INTERLOCK DOO SWITCH-REED*DOOR INTERLOCK*6 SPRING-INTERLOCK DOOR SWITCH A.-TORQUE *H60* HUB A.-ARM SWITCH-LEVER-SPDT-1A-125V +SPRING-TORQUE*BROWN* +KNOB-ADJUSTMENT +SCREW-ADJUSTMENT SWITCH-MEMBRANE-5 POSITION-8 SWITCH-PRESSURE 440 PSI-SOLD SWITCH-TOGGLE-DPDT*ON-NONE-ON TANK-GLYCOL 1.
+ Available Separately Models H62 & H63 51 Parts List 007530 004338 007530 004227 039421 024156 039423 039424 024156 068443 051958-33 051958-40 023606 051960 051957-40 051958-58 068439-03 067368-39 067368-40 067368-58A 067368-58 X68450 068440-A 062388 020571 016030 067192 016533 X56119 067365-G BELT-V-4L370 BLOCK-TERMINAL 2P L1, N BLOCK-TERMINAL 7P GREEN BLOCK-TERMINAL 3P L1,L2,L BLOCK-TERMINAL 4P L1, L2, L3, N BLOCK-TERMINAL 7P GREEN BUTTON A.
+ Available Separately Parts List 52 Models H62 & H63 HARNESS-WIRE 5472 MAIN PO HARNESS-WIRE-MAIN POWER * HARNESS-WIRE-MAIN POWER * HARNESS-WIRE-CTRL*0H62*CA HARNESS A.-WIRE-RS80 380V HARNESS A.-WIRE-RS80 380V HARNESS-WIRE 5472 COND FA HARNESS-WIRE H63 POWER 1/ MOTOR-1/2 HP MOTOR-FAN 75 WATT MOTOR-FAN 100W 220-240V 5 OVERLOAD-THERMAL-3P-2.
H62/H63 067368--27 10/11
H62/H63 067368--33 10/11
H62/H63 067368--40 10/11
H62/H63 067368--58 10/11
