Owner's Manual

ManualsBrandsTascam ManualsAudioTascam HS-2

100

100 TASCAM HS-2

•

VNC (Virtual Network Computing)

You can operate the system on a computer by displaying

the screen which is displayed on this unit’s LCD on the

computer using VNC Viewer Application.

You can operate the following using a mouse on the VNC

Viewer Application.

Left click of the mouse : Operates in the same way as touching

the LCD of this unit.

Mouse wheel click : Operates in the same way as the ENTER

key of this unit.

Mouse wheel rotate : Operates in the same way as the DATA

dial of this unit.

Mouse wheel press

and rotate

: Operates in coarse settings in the same

way as when you press and rotate the

DATA dial of this unit (COARSE mode op-

eration).

You can perform the following operations using the

computer keyboard with the VNC Viewer Application

active.

F1 to F12 key : Operate in the same way as an external

keyboard connected with this unit.

See “Section 12 Other functions” Opera-

tions using the computer keyboard –Key-

board Operation” in the Operation Manual

of this unit.

HOME key : Operates in the same way as the HOME

key of this unit and displays the HOME

screen. Press the End key while hold-

ing the HOME key to display the

LOCK

SETUP

screen.

End key : Operates in the same way as the MENU

key of this unit and displays the

screen. Press the End key while hold-

ing the HOME key to display the

LOCK

SETUP

screen.

PageDown : Operates in the same way as the PROJECT

key of this unit and displays the

PROJ-

ECT

screen.

Cursor 2 key : Operates in the same way as rotating the

DATA dial of this unit clockwise.

when editing parameter values, or scrolls

the list up when the screen shows a list.

Cursor x key : Operates in the same way as rotating the

DATA dial of this unit anti-clockwise.

when editing parameter values, or scrolls

the list down when the screen shows a list.

Character input keys : Input the characters while this unit dis-

plays the keyboard screen.

•

Setting values necessary to connect with VNC

Setting values necessary to connect VNC Viewer Appli-

cation with this unit are as follows:

IP Address : The IP Address of this unit is shown in IP Ad-

dress on the

ETHERNET

page of the

REMOTE

SETUP

screen.

Password : The default password is “HS-2”.

Distinguishes between capital letters and small

letters.

You can change the password using the

Password [Change ]

button on the

ETHERNET

page of the

REMOTE SETUP

screen.

NOTE

•

Only one active VNC connection is allowed.

•

EXTERNAL Control

" on the

LOCK SETU

P screen

is set to

LOC

K, display in the VNC Viewer Application

is possible, but mouse and keyboard interaction is

ignored.

•

If you change any setting on the E

THERNET

page on

the

REMOTE SETUP

screen while a VNC connection is

active, that VNC session will be disconnected.

•

Please consult with TASCAM Customer Support for

information about VNC Viewer Applications that have

been tested with this unit.

•

VNC Viewer Application response will slow down when

a file is being transferred by FTP, or at high system Fs

rates (88.2kHz/96kHz/176.4kHz/192kHz)

Audio Signal Input and Output

settings (AUDIO I/O)

Input and Output Audio signal settings can be changed

here.

The

AUDIO I/O

screen has two pages:

INPUT

and

OUTPUT

Touch the tabs at the bottom of the screen to open the

corresponding page.

INPUT page

Make input settings on this page.

INPUT SOURCE

You can set the input source. Select analog XLR input,

analog RCA input or digital input.

Setting buttons:

Analog XLR

(Default),

Analog RCA

Digital X

(“

” stands for either

AES/EBU

S/PDIF

)

DIGITAL SOURCE

You can select the digital input source.

Setting buttons:

AES/EBU

(Default),

S/DIF

Fs CONVERT

Turn the sampling rate converter ON or OFF (default) for

each pair of inputs.

10–Internal settings