Model #TPPER94033 USE AND CARE GUIDE 10’x10’ Curved Roof Pergola
Table of Contents Table of Contents .......................................................... 2 Safety Information......................................................... 2 Warranty ......................................................................... 2 What is Covered .......................................................................2 What is Not Covered ................................................................2 Warning......................................................................
Pre-installation PLANNING INSTALLATION To prevent damage, place all parts on a soft surface during assembly. Tools required for assembly (not included): Allen wrench (included), hammer, screwdriver, stepladder, level and other safety items such as gloves, safety goggles and hardhat. NOTE: Too ls and pr o tective articl es bel o w are no t pro vid ed . TOOLS REQUIRED Hammer Screwdriver Safety goggles Gloves Hardhat Stepladder HARDWARE INCLUDED NOTE: Hardware not shown to actual size.
Pre-ins tallation (con tinued) PACKAGE CONTENTS A1 A2 B1 B2 C1 C2 D1 D2 E1 E2 4
Pre-installation (continued) PACKAGE CONTENTS F G1 G2 H I J K 5
Pre-installation (continued) PACKAGE CONTENTS L1 L2 N M 6
Pre-ins tallation (con tinued) PACKAGE CONTENTS Part Description Quantity A1 Left Raffter,Female 1 A2 Left Raffter,Male 1 B1 Center Rafter,Female 5 B2 Center Rafter,Male 5 C1 Right Rafter,Female 1 C2 Right Rafter,Male 1 D1 Rear Beam,Male 1 D2 E1 E2 Rear Beam,Female Front Beam,Male 1 1 Front Beam,Female 1 F Canopy 1 G1 Rod,Male 2 G2 H Rod,Female Post 1 2 2 I Post 2 2 J Post Skirt 4 K Plate 4 L1 L2 M Brace 1 Brace 2 2 2 Brace 3 2 N Brace 4 2 7
Operation 1 A2 A1 B2 B1 C2 C1 Set aside all rafter pieces.Assemble the left rafter by inserting the left rafter,male (A1) into the left rafter,female (A2).Secure the top of the joined rafter with a plastic washer (DD) and M6*15 mm bolt (AA). Pipe Skirt Secure the bottom of the rafter with a washer (EE) and M6*15 mm bolt (AA). Slide the preassembled pipe skirt on the joined rafter.Secure pipe skirt with a washer (DD) and M6*15 mm bolt (AA).
Oper ation (continued) 2 D1 E1 D2 E2 Set aside all beam. Assemble the rear beam by inserting the rear beam, male (D1) into the rear beam, female (D2). Secure the of the joined beam with a plastic washer (DD) and M6*15 mm bolt (AA). Secure the bottom of the beam with a washer (EE) an M6*15 mm bolt (AA). DD Repeat this process for the front beam using the front beam, male (E1) and front beam, female (E2).
Oper ation (continued) 3 Slide one post skirt (J) onto each post 1 (H) and post 2 (I). H I Attach one plate (K) to each post 1 (H) and post 2 (I). Secure each with washers (EE) and M6*15 mm bolt (AA).
Oper ation (continued) 4 D1 D2 I H BB Attach rear beam (D1/D2) to post 1 (H) DD and post 2 (I). Secure with plastic washers (DD) and M6*95 mm bolts (BB). Repeat for front beam (E1/E2).
Oper ation (continued) 5 A1 A2 H I Attach left rafter (A1/A2) to the top BB of the beam and post assembly. Secure on both sides with plastic washers (DD) and M6*95mm bolt (BB). Repeat for right rafter (C1/C2).
Oper ation (continued) 6 D2/E2 Slide the pipe skirt on the center of the beam (D1D2/E1E2) as shown, then attach center rafter (B1/B2) to the top center of the beam. Secure with plastic washer (DD) and M6*95 mm bolt (BB). Repeat for four remaining center rafters (B1/B2).
Oper ation (continued) 7 L1 L2 L2 L1 Attach a brace (L1/L2) to the pergola assembly as shown. Secure with washers (EE) and M6*15 mm bolt (AA). Repeat for remaining braces (L1/L2).
Oper ation (continued) 8 N M N M Attach a brace (N/M) to the pergola assembly as shown. Secure with washers (EE) and M6*15 mm bolts (AA). Repeat for remaining brace (N/M).
Oper ation (continued) 9 Insert rod, male (G1) into rod, female (G2). Insert rod assembly into canopy (F). Repeat for remaining rod assembly.
Oper ation (continued) 10 F Place canopy (F) over pergola. Tie corners of canopy (F) to each post.
Oper ation (continued) 11 J Insert stakes (FF) into plate (K). Place post skirt (J) over plate (K). Repeat for remaining stakes (FF) and post skirts (J).
