Manual

4.3 Parameter List
e30bu689.10
0-** Operation / Display
0-0* Basic Settings
0-01 Language
0-03 Regional Settings 0-04 Operating State at Power-up
0-06 GridType
0-07 Auto DC Braking
0-1* Set-up Operations 0-10 Active Set-up
0-11 Programming Set-up 0-12 Link Setups 0-3* LCP Custom Readout 0-30 Custom Readout Unit
0-31 Custom Readout Min Value 0-32 Custom Readout Max Value
0-37 Display Text 1
0-38 Display Text 2 0-39 Display Text 3
0-4* LCP Keypad
0-40 [Hand on] Key on LCP
0-42 [Auto on] Key on LCP
0-5* Copy/Save 0-50 LCP Copy
0-51 Set-up Copy
0-6* Password 0-60 Main Menu Password
0-61 Access to Main Menu w/o Password
1-** Load and Motor 1-0* General Settings
1-01 Motor Control Principle 1-03 Torque Characteristics
1-06 Clockwise Direction 1-08 Motor Control Bandwidth
1-1* Motor Selection 1-10 Motor Construction 1-14 Damping Gain 1-15 Low Speed Filter Time Const.
1-16 High Speed Filter Time Const.
1-17 Voltage time const. 1-2* Motor Data
1-20 Motor Power 1-22 Motor Voltage
1-23 Motor Frequency
1-24 Motor Current
1-25 Motor Nominal Speed
1-26 Motor Cont. Rated Torque
1-29 Automatic Motor Adaption (AMA) 1-3* Adv. Motor Data 1-30 Stator Resistance (Rs)
1-31 Rotor Resistance (Rr)
1-33 Stator Leakage Reactance (X1) 1-35 Main Reactance (Xh)
1-37 d-axis Inductance (Ld) 1-38 q-axis Inductance (Lq)
1-39 Motor Poles
1-4* Adv. Motor Data II
1-40 Back EMF at 1000 RPM
1-42 Motor Cable Length
1-43 Motor Cable Length Feet 1-44 d-axis Inductance Sat. (LdSat) 1-45 q-axis Inductance Sat. (LqSat) 1-46 Position Detection Gain
1-48 Current at Min Inductance for d-axis
1-49 Current at Min Inductance for q-axis
1-5* Load Indep. Setting 1-50 Motor Magnetisation at Zero Speed
1-52 Min Speed Normal Magnetising [Hz] 1-55 U/f Characteristic - U
1-56 U/f Characteristic - F 1-6* Load Depen. Setting 1-60 Low Speed Load Compensation
1-61 High Speed Load Compensation 1-62 Slip Compensation 1-63 Slip Compensation Time Constant
1-64 Resonance Dampening 1-65 Resonance Dampening Time Constant
1-66 Min. Current at Low Speed 1-7* Start Adjustments
1-70 Start Mode 1-71 Start Delay
1-72 Start Function
1-73 Flying Start
1-8* Stop Adjustments 1-80 Function at Stop
1-82 Min Speed for Function at Stop [Hz]
1-88 AC Brake Gain
1-9* Motor Temperature
1-90 Motor Thermal Protection 1-93 Thermistor Source
2-** Brakes 2-0* DC-Brake
2-00 DC Hold/Motor Preheat Current 2-01 DC Brake Current
2-02 DC Braking Time 2-04 DC Brake Cut In Speed
2-06 Parking Current
2-07 Parking Time
2-1* Brake Energy Funct. 2-10 Brake Function
2-16 AC Brake, Max current 2-17 Over-voltage Control
2-19 Over-voltage Gain 3-** Reference / Ramps
3-0* Reference Limits 3-02 Minimum Reference
3-03 Maximum Reference
3-1* References 3-10 Preset Reference
3-11 Jog Speed [Hz]
3-14 Preset Relative Reference 3-15 Reference 1 Source 3-16 Reference 2 Source
3-17 Reference 3 Source
3-4* Ramp 1
3-41 Ramp 1 Ramp Up Time 3-42 Ramp 1 Ramp Down Time
3-5* Ramp 2
3-51 Ramp 2 Ramp Up Time
3-52 Ramp 2 Ramp Down Time 3-8* Other Ramps 3-80 Jog Ramp Time
3-81 Quick Stop Ramp Time
4-** Limits / Warnings
4-1* Motor Limits 4-10 Motor Speed Direction
4-12 Motor Speed Low Limit [Hz] 4-14 Motor Speed High Limit [Hz]
4-18 Current Limit 4-19 Max Output Frequency 4-4* Adj. Warnings 2 4-40 Warning Freq. Low
4-41 Warning Freq. High
4-5* Adj. Warnings 4-50 Warning Current Low
4-51 Warning Current High 4-54 Warning Reference Low
4-55 Warning Reference High 4-56 Warning Feedback Low
4-57 Warning Feedback High
4-58 Missing Motor Phase Function
4-6* Speed Bypass
4-61 Bypass Speed From [Hz]
4-63 Bypass Speed To [Hz]
4-64 Semi-Auto Bypass Set-up
5-** Digital In/Out 5-0* Digital I/O mode
5-00 Digital Input Mode
5-03 Digital Input 29 Mode 5-1* Digital Inputs
5-10 Terminal 18 Digital Input
5-11 Terminal 19 Digital Input 5-12 Terminal 27 Digital Input
5-13 Terminal 29 Digital Input
5-3* Digital Outputs 5-34 On Delay, Digital Output 5-4* Relays 5-40 Function Relay
5-41 On Delay, Relay
5-42 Delay, Relay 5-5* Pulse Input
5-50 Term. 29 Low Frequency
5-51 Term. 29 High Frequency
5-52 Term. 29 Low Ref./Feedb. Value
5-53 Term. 29 High Ref./Feedb. Value
5-9* Bus Controlled 5-90 Digital & Relay Bus Control
6-** Analog In/Out
6-0* Analog I/O Mode 6-00 Live Zero Timeout Time 6-01 Live Zero Timeout Function
6-02 Fire Mode Live Zero Timeout Function
6-1* Analog Input 53
6-10 Terminal 53 Low Voltage
6-11 Terminal 53 High Voltage
6-12 Terminal 53 Low Current
6-13 Terminal 53 High Current
6-14 Terminal 53 Low Ref./Feedb. Value 6-15 Terminal 53 High Ref./Feedb. Value 6-16 Terminal 53 Filter Time Constant
6-19 Terminal 53 mode
6-2* Analog Input 54
6-20 Terminal 54 Low Voltage 6-21 Terminal 54 High Voltage
6-22 Terminal 54 Low Current 6-23 Terminal 54 High Current 6-24 Terminal 54 Low Ref./Feedb. Value
6-25 Terminal 54 High Ref./Feedb. Value 6-26 Terminal 54 Filter Time Constant
6-29 Terminal 54 mode 6-7* Analog/Digital Output 45
6-70 Terminal 45 Mode 6-71 Terminal 45 Analog Output
6-72 Terminal 45 Digital Output 6-73 Terminal 45 Output Min Scale 6-74 Terminal 45 Output Max Scale
6-76 Terminal 45 Output Bus Control 6-9* Analog/Digital Output 42
6-90 Terminal 42 Mode
6-91 Terminal 42 Analog Output
6-92 Terminal 42 Digital Output
6-93 Terminal 42 Output Min Scale
6-94 Terminal 42 Output Max Scale
6-96 Terminal 42 Output Bus Control
6-98 Drive Type 8-** Comm. and Options 8-0* General Settings 8-01 Control Site 8-02 Control Source
8-03 Control Timeout Time
8-04 Control Timeout Function 8-3* FC Port Settings 8-30 Protocol
8-31 Address
8-32 Baud Rate
8-33 Parity / Stop Bits
8-35 Minimum Response Delay
8-36 Maximum Response Delay
8-37 Maximum Inter-char delay
8-4* FC MC protocol set
8-43 PCD Read
8-5* Digital/Bus
8-50 Coasting Select 8-51 Quick Stop Select 8-52 DC Brake Select
8-53 Start Select
8-54 Reversing Select 8-55 Set-up Select
8-56 Preset Reference Select
8-7* BACnet 8-70 BACnet Device Instance
8-72 MS/TP Max Masters
8-73 MS/TP Max Info Frames
8-74 "I am" Service 8-75 Intialisation Password
8-79 Protocol Firmware version
8-8* FC Port Diagnostics 8-80 Bus Message Count
8-81 Bus Error Count
8-82 Slave Messages Rcvd 8-83 Slave Error Count 8-84 Slave Messages Sent 8-85 Slave Timeout Errors 8-88 Reset FC port Diagnostics
8-9* Bus Feedback 8-94 Bus Feedback 1
8-95 Bus Feedback 2 13-** Smart Logic 13-0* SLC Settings
13-00 SL Controller Mode 13-01 Start Event
13-02 Stop Event
13-03 Reset SLC
13-1* Comparators
13-10 Comparator Operand
13-11 Comparator Operator
13-12 Comparator Value
13-2* Timers
13-20 SL Controller Timer 13-4* Logic Rules
13-40 Logic Rule Boolean 1 13-41 Logic Rule Operator 1
13-42 Logic Rule Boolean 2
13-43 Logic Rule Operator 2
13-44 Logic Rule Boolean 3
13-5* States
13-51 SL Controller Event 13-52 SL Controller Action
14-** Special Functions 14-0* Inverter Switching
14-01 Switching Frequency 14-03 Overmodulation
14-07 Dead Time Compensation Level 14-08 Damping Gain Factor 14-09 Dead Time Bias Current Level
14-1* Mains Failure
14-10 Mains Failure 14-11 Mains Fault Voltage Level
14-12 Response to Mains Imbalance
14-15 Kin. Back-up Trip Recovery Level
14-2* Reset Functions
14-20 Reset Mode 14-21 Automatic Restart Time
14-22 Operation Mode 14-23 Typecode Setting
14-27 Action At Inverter Fault
14-28 Production Settings
14-29 Service Code
14-3* Current Limit Ctrl.
14-30 Current Lim Ctrl, Proportional Gain
14-31 Current Lim Ctrl, Integration Time
14-32 Current Lim Ctrl, Filter Time
Programming
Operating Guide | VLT® HVAC Basic Drive FC 101
AQ275641848264en-000101 / 132R0078| 61
Danfoss A/S © 2019.11