L BAL E234 GB MANUAL
Table Of Contents
- 1 General notes
- 2 Safety instructions
- 2.1 Intended use
- 2.2 Explanations of symbols
- 2.3 Product safety
- 2.3 Product safety
- 2.4 Requirements placed on the personnel / due diligence
- 2.4 Requirements placed on the personnel / due diligence
- 2.5 Start–up and during operation
- 2.5 Start–up and during operation
- 2.6 Work on the device
- 2.6 Work on the device
- 2.7 Modifications / interventions in the device
- 2.7 Modifications / interventions in the device
- 2.8 Operator’s obligation of diligence
- 2.8 Operator’s obligation of diligence
- 2.9 Employment of external personnel
- 2.9 Employment of external personnel
- 3 Product overview
- 3 Product overview
- 4 Mounting
- 4 Mounting
- 4.1 General notes
- 4.1 General notes
- 4.2 Connection pressure measuring tube
- 4.2 Connection pressure measuring tube
- 4.3 Outdoor installation
- 4.3 Outdoor installation
- 4.4 Installation location for agriculture
- 4.4 Installation location for agriculture
- 4.5 Temperature influences during commissioning
- 4.5 Temperature influences during commissioning
- 5 Electrical installation
- 5 Electrical installation
- 5.1 Safety precautions
- 5.1 Safety precautions
- 5.2 EMC–compatible installation of control lines
- 5.2 EMC–compatible installation of control lines
- 5.3 Mains connection
- 5.3 Mains connection
- 5.4 Signal input or sensor connection (E2)
- 5.4 Signal input or sensor connection (E2)
- 5.5 Control outputs 0 – 10V (A1, A2)
- 5.5 Control outputs 0 – 10V (A1, A2)
- 5.6 Voltage supply for external devices (+, GND)
- 5.6 Voltage supply for external devices (+, GND)
- 5.7 Digital inputs (D1, D2)
- 5.7 Digital inputs (D1, D2)
- 5.8 Relay outputs
- 5.8 Relay outputs
- 5.9 RS–485 interfaces for MODBUS RTU
- 5.9 RS–485 interfaces for MODBUS RTU
- 5.10 USB–interface
- 5.10 USB–interface
- 5.11 Potential at control voltage connections
- 5.11 Potential at control voltage connections
- 6 Select operation mode
- 6 Select operation mode
- 7 Start–up
- 8 Controls and Menu
- 9 Programming
- 9.1 Pressure control airconditioning
- 9.2 Menu group Start
- 9.3 Menu group Info
- 9.4 Controller Setup
- 9.4.1 PIN protection
- 9.4.2 PIN protection
- 9.4.3 user settings
- 9.4.4 Sensor Alarm ON / OFF
- 9.4.5 Limit
- 9.4.6 Minimum speed cut off
- 9.4.7 Reverse action of the control function
- 9.4.8 Controller configuration
- 9.4.9 Group control
- 9.4.10 Display text for external message
- 9.4.11 Offset control signal
- 9.4.12 Selection amplifier (comparator) control circuit 1 or 2 at output A1
- 9.4.13 Data on the total control deviation
- 9.5 IO Setup
- 9.5.1 Analog outputs
- 9.5.2 Digital inputs
- 9.5.2.1 Menu overview
- 9.5.2.2 Enable
- 9.5.2.3 External message, Function
- 9.5.2.4 Limit ON / OFF, Function
- 9.5.2.5 Switch over input
- 9.5.2.6 Output control circuit 2 additional to
- 9.5.2.7 Set 1/2 or Setpoint 1/2, Function
- 9.5.2.8 Intern / Extern Function
- 9.5.2.9 Automatic control / speed manual Function
- 9.5.2.10 Reverse action of control function (
- 9.5.2.11 Switch over Setpoint 1/2 for control circuit 2
- 9.5.2.12 Setting Max. Speed ON / OFF function
- 9.5.2.13 Switch over Setpoint 1/2 and Pband 1/ 2 for control circuit 1
- 9.5.2.14 Switch over Setpoint 1/2 and Pband 1/2 for control circuit 2
- 9.5.2.15 Timer function overwrite
- 9.5.3 Configuration of analog inputs
- 9.5.4 Function and inverting for relay outputs
- 9.5.5 COM2
- 9.6 Limits
- 9.7 Timer
- 9.8 MODBUS Slave
- 9.9 MODBUS Master
- 9.10 Member MOBUS Master
- 10 Menu tables
- 10
- 11 Diagnostics menu
- 12 Protocol
- 13 Enclosure
For operation as controller (starting from 2.01 ): switch over “Setpoint 1” / “external Setpoint ”
Possible only for operation with one control circuit!
Under Base setup “E2 function” programmed to function
|
1E
|
for “external setpoint” .
Contact at digital input e.g. “Digital In 1” = “D1” - “D1”
Controller
24V
D1 D1
10
n = 0 – 100 %
- - - - -
Se
ES E2
26.05.2010
v_6d_sollwert1_externer_sollwert.vsd
1
1 Setting “Setpoint1”
ES External Setpoint e.g. 5 V
23.8°C
Se Sensor
•
“D1 Inverting” = “ON”: Setting at the unit at
opened contact / Signal Extern at closed
contact
•
“D1 Inverting” = “OFF”: Setting at the unit at
closed contact / Signal Extern at opened
contact
9.5.2.9 Automatic control / speed manual Function
|
7D
|
(mode 2.01 )
Possible only for operation with one control circuit!
Switch over between automatic control to set target value (depending on the activation: “Setpoint1”,
“Setpoint2”) and the default for “manual operation” set at the device.
If for Analog In 2 “E2 function” is programmed to
|
2E
|
switch over between “Setpoint1” or “Setpoint2”
and external manual operation. With activated manual mode the display constantly changes between
“actual value” and value for “manual mode”.
Contact at digital input e.g. “Digital In 1”
Controller
24V
D1 D1
10
n = 0 -100 %
1
n = 80 %
0
- - - - -
- - - - -
- - - - -
Se
E1
ES E2
26.05.2010
v_7d_regelung_hand.vsd
3
2
1
1 Setting “Setpoint1”
2 Setting “Setpoint2”
3 Setting “Speed manual” (depending on device type in: %, Hz, rpm)
EH Signal for Manual mode extern, E2 Function =
|
2E
|
Se Sensor
•
“D1 Inverting” = “OFF” Automatic control at
opened contact / manual operation at closed
contact.
•
“D1 Inverting” = “ON”: Automatic control at
closed contact / manual operation at opened
contact.
9.5.2.10 Reverse action of control function (
2.01 ), Function
|
8D
|
Switchover between: Increasing modulation during increasing actual-value and increasing modulation
during sinking actual-value.
The factory presets for the “Control function” are dependent on the selected mode of operation (
Controller Setup - reverse operation of the control function).
When switching over via a digital input, the device works with the opposite function as set there.
The inversion of the control function influences both circuits in operation with two control circuits.
Controller Setup Settings in Controller Setup
Display for operation with two control circuits:
“1. Actual>Set=n” for control circuit 1
“2. Actual>Set=n” for control circuit 2
ON
Val>Set=n+
Operating Instructions POC-M Programming
L-BAL-E234-GB 1614 Index 002 Part.-No.
45/84