SYSLOGIC – Installation Operation Manual (IOM LOGIC 02 N 3GB)

English
To override the ECO mode, the Fdi parameter must be set to 0 (Eco)
Caution
16 SYSLOGIC
6. PARAMETER TABLE MODBUS
After modication of MODBUS address, the new “Adr” value become actual only if MB2 module (586507
part number) have been properly recognized.
Without MB2 module the valid MODBUS address is always the default one: 1.
PAR. Description M.U. Min Max Default
MODBUS
Modiable via
MRC/WRC
Type Gain Adress*
P00 Septpoint differential °C / °F 0.2 2 0.5 UW 0.1 40002

P01 Auto-changeover deadband °C / °F 1 5 3 UW 0.1 40003

P02
Temperature unit:
0 = Celsius
1 = Farenheit
enum 0 1 0 enum 1 40023

P05 Offset air temperature (heating mode) °C / °F -5 5 0 SW 0.1 40004

P06 Offset air temperature (cooling mode) °C / °F -5 5 0 SW 0.1 40005

Pdi
Digital input polarity 1
0 = Normally open
1 = Normally closed
enum 0 1 1 B 1 40024

P09 Temperature setpoint for electrical heater °C / °F 30 122 40 UW 0.1 40006

P10 Temperature hysteresis for electrical heater °C / °F 0.4 2 2 UW 0.1 40007

P11 Temperature setpoint °C / °F P23 P24 21 UW 0.1 40008

P18 Reduced mode offset °C / °F 1 15 3 UW 0.1 40009

P19 Fan ON time in heating mode min 0 900 1 UW 1 40010

P20 Fan OFF time in heating mode min 0 900 20 UW 1 40011

P21 Fan ON time in cooling mode min 0 900 1 UW 1 40012

P22 Fan OFF time in cooling mode min 0 900 20 UW 1 40013

P29 Water valve OFF time sec 1 900 600 UW 1 40014

P30 Water valve ON time sec 0 900 240 UW 1 40015

Fdi
DI1 configuration:
0 = Eco mode
1 = ON/OFF
enum 0 1 1 UW 1 40025

P80 Set voltage EC motor - low speed V/100 0 999 330 UW 1 40016

P81 Set voltage EC motor - medium speed V/100 0 999 660 UW 1 40017

P82 Set voltage EC motor - high speed V/100 0 999 990 UW 1 40018

F-Adr Slave address - 1 247 1 UW 1 40020

F-bAU
Baud rate:
0 = 9600
1 = 19200
2 = 38400
- 0 2 0 UW 1 40021

F-PtY
Parity:
0 = none
1 = odd
2 = even
- 0 2 0 UW 1 40022

AtS
Reference temperature control probe:
0 = Aib (Entering air temperature)
1 = AiL (WRC/MRC/IR receiver)
2 = mean (AiL/Aib)
3 = heating: AiL, cooling mean
enum 0 3 1 UW 0.1 40027

FaN
Ventilation speed:
1 = MIN
2 = MED
3 = MAX
4 = AUTO
enum 1 4 1 UW 1 40019

ECO
Override the ECO mode
0 = eco OFF
1 = eco ON
enum 0 1 0 UW 1 40028

6.1. CONFIGURATION PARAMETERS
* Addresses are of the holding registers type.