IOM SYSAQUA 45 125 (IOM AQA 05 N 3GB)
Table Of Contents
- CONTENTS
- 1. GENERAL RECOMMENDATIONS
- 2. INSPECTION AND STORAGE
- 3. WARRANTY
- 4. PRESENTATION
- 5. CONTENTS OF PACKAGE
- 6. DIMENSIONS
- 7. HANDLING
- 8. TECHNICAL SPECIFICATIONS
- 9. INSTALLATION
- 10. HYDRAULIC LINKS
- 11. WIRING DIAGRAM AND LEGEND
- 12. ELECTRICAL CONNECTIONS
- 13. REGULATION
- 13.1. ORDER OF PRIORITY FOR CONTROL SYSTEMS
- 13.2. USER INTERFACE
- 13.3. INITIAL SETTINGS
- 13.4. LAUNCHING THE SYSAQUA SYSTEM
- 13.4.1. CONFIGURING INPUT D1
- 13.4.2. CONFIGURING INPUT D2
- 13.4.3. HEAT/COOL SELECTION
- 13.4.4. SELECTING THE OPERATING MODE
- 13.4.5. USER TEMPERATURE SETPOINTS AND ACTUAL SETPOINTS
- 13.4.6. WATER LAW
- 13.4.7. "VARIABLE PRIMARY FLOW” OPTION
- 13.4.8. ELECTRIC HEATING OPTION
- 13.4.9. REDUCED MODE
- 13.4.10. LIMITED CAPACITY
- 13.5. ALARMS
- 13.6. SCHEDULE
- 14. COMMISSIONING
- 15. IN CASE OF WARRANTY - MATERIAL RETURN PROCEDURE
- 16. ORDERING SERVICE AND SPARE PARTS ORDER
- 17. MAINTENANCE
- 18. TROUBLE SHOOTING
- DIMENSIONS
- REFRIGERANT CIRCUIT DIAGRAM
- HYDRAULIC CIRCUIT DIAGRAM
- PRESSURE LOSSES OF THE PLATE HEAT EXCHANGER
- HYDRAULIC PUMPS CURVES
- WIRING DIAGRAM
- DIMENSIONS
- SCHEMA DU CIRCUIT FRIGORIFIQUE
- SCHEMA DU CIRCUIT HYDRAULIQUE
- PERTE DE CHARGE DE L'ECHANGEUR A PLAQUES
- COURBES DES POMPES HYDRAULIQUES
- SCHEMAS ELECTRIQUES
- ABMESSUNGEN
- KÄLTEKREISLAUFDIAGRAMM
- HYDRAULISCHER SCHALTPLAN
- DRUCKVERLUST PLATTENWÄRMETAUSCHER
- KURVEN VON HYDRAULIKPUMPEN
- STROMLAUFPLANS
- DIMENSIONI
- SCHEMA DEL CIRCUITO REFRIGERANTE
- SCHEMA CIRCUITALE IDRAULICO
- PERDITA DI CARICO SCAMBIATORE A PIASTRE
- CURVE DELLE POMPE IDRAULICHE
- SCHEMA ELETRICO
- DIMENSIONES
- ESQUEMA DEL CIRCUITO FRIGORIFÍCO
- ESQUEMA CIRCULAR HIDRÁULICO
- PÉRDIDA DE CARGA INTERCAMBIADOR DE PLACAS
- CURVAS BOMBAS HIDRÁULICAS
- ESQUEMA ELECTRICO
English
40 SYSAQUA
14.2.5. COMPRESSOR AND REFRIGERATION SYSTEM
1. Running check: Start the compressor. Check for any unusual noise or vibration.
2. Operating Pressures: Operate the unit for at last 20 minutes and ensure that the refrigerant pressures
are stabilised, and cheek that they are within the normal operating ranges.
3. Operating Temperature: Check discharge, suction and liquid temperatures.
4. Discharge temperature on cooling cycle should normally not exceed 115°C.
5. Suction superheat should be 6K ±2K.
1. All panels and fan guards are in place and secured.
2. Unit clean and free of remainder installation material.
Material must not be returned without permission of our After Sales Department.
To return the material, contact your nearest sales ofce and ask for a "return form". The return form shall
be sent with the returned material and shall contain all necessary information concerning the problem
encountered.
The return of the part is not an order for replacement. Therefore, a purchase order must be entered through
your nearest distributor or regional sales ofce. The order should include part name, part number, model
number and serial number of the unit involved.
Following our personal inspection of the returned part, and if it is determined that the failure is due to faulty
material or workmanship, and in warranty, credit will be issued on customer's purchase order. All parts shall
be returned to our factory, transportation charges prepaid.
The part number, the order conrmation and the unit serial number indicated on the name plate must be
provided whenever service works or spare parts are ordered.
For any spare part order, indicate the date of unit installation and date of failure. Use the part number
provided by our service spare parts, if it not available, provide full description of the part required.
14.2.6. FINAL CHECK
15. IN CASE OF WARRANTY - MATERIAL RETURN PROCEDURE
16. ORDERING SERVICE AND SPARE PARTS ORDER