SYSTEMP – Installation Operation Manual (IOM SYSTEMP rev.N)

7
WARRANTY RESTRICTIONS
The above mentioned warranty conditions are valid as long as the Customer has fullled all obligations according to the contract and in
particular those relating to payment. A delayed payment or non-payment of the supply, even if partial, suspends any warranty. The warranty does not
give the Customer any right to suspend or delay payments, which must be paid in any case according to the stipulations of the order and specied
in the written order conrmation.
Without precluding due compliance with other instructions provided in the technical documentation supplied with the product, it must be
noted that the following instructions must be complied with accordingly, in order for the warranty to be valid:
Transport and positioning
• Do not remove the product from its original packaging until it has reached the installation site.
• Do not drop, knock or shake the product, as the internal circuits and mechanisms may be irreparably damaged.
• Store the product in an environment that complies with the temperature and humidity limits specied in the technical documentation.
Installation
1) The product must be installed by skilled personnel who full the adequate requisites for the task as dened by the regulations in the coun-
try where positioning and installation take place.
2) The system that will control the product must be implemented according to professional standards, according to the instructions provided
in the technical documentation and the regulations of the country where positioning and installation take place, with particular attention
to the setting up of:
• Water or cooling lines serving the product and the relevant components.
• Electrical power and connection lines of the product and the relevant components.
• Aeraulic lines of the product and the relevant components.
3) Do not install the product outdoors or in areas that are subject to adverse weather.
4) Do not install the product in areas where there is oil, or where there are oil vapours or various kinds of aerosols, and where there are am-
mable vapours.
5) Do not install the product in environments where there is equipment that generates electromagnetic waves, and where the line voltage is
subject to great uctuations.
6) Do not install the product in environments where the air contains corrosive pollutants, a high dust or salt content.
7) Do not install the product on vehicles or boats.
First start-up
1) The product must be started up by skilled personnel who full the qualication requisites for the task as dened by the regulations in the
country where positioning and installation take place.
2) The system controlling the units must be started up according to professional standard, according to the instructions provided in the tech-
nical documentation and the regulations of the country where positioning and installation take place.
3) A copy of the technical start-up report of the product must be delivered to the Manufacturer.
Use and maintenance
1) Do not use the product for applications other than those specied in the technical documentation.
2) Do not use the product in an environment that does not comply with the temperature and humidity limits specied in the technical documentation.
3) Perform maintenance cycles according to the schedules specied in the technical documentation.
4) Clean the product with neutral detergents. Do not use corrosive chemicals and solvents or aggressive detergents.
Furthermore, the Manufacturer reserves the right to void the warranty of the products sold if:
A) The labels or plates bearing the trademark of the Manufacturer and the serial number or the registration number of the product have been
deleted and/or removed.
B) The product has been subjected to alterations or mechanical processes not specically authorised by the Manufacturer.
C) The product has been used inconsistently with the instructions provided in the technical documentation and regulations of the country
where positioning and installation take place, or for purposes other than what it was designed for.
D) The defects are due to negligence, incompetence, poor maintenance, carelessness and inability of the End-user, damage caused by third
parties, unforeseeable circumstances or force majeure or for any other reason not attributable to defects in the construction quality.
The following are henceforth considered excluded from the warranty:
A) All parts with marginal defects that have a negligible eect on the value or function of the product.
B) All parts typically subject to sliding or rolling friction (bearings, brushes, etc.).
C) All parts typically subject to consumption (lters, humidier cylinders, etc.).
D) All parts typically subject to oxidation or corrosion if not properly used or serviced (headers, wires and copper contacts or metal alloys,
internal or external parts of the units, etc.).
E) All parts not supplied by the Manufacturer, even if these are an integral part of the system that controls the product.