MODBUS LITE V5.01 parameter specification
Table Of Contents
- 1 Frame protocol
- 2 Holding Register
- 2.1 Overview
- 2.2 Reset
- 2.3 Default set value
- 2.4 Password
- 2.5 Control default setting
- 2.6 Control customer setting
- 2.7 Operating hours counter
- 2.8 Operating minutes counter
- 2.9 Fan address
- 2.10 Source set value
- 2.11 Preferred running direction
- 2.12 Save set value
- 2.13 Internal parameter set
- 2.14 Control mode
- 2.15 Control parameters
- 2.16 Maximum modulation level
- 2.17 Minimum modulation level
- 2.18 Enable motor stop
- 2.19 Set value (EEPROM)
- 2.20 Starting modulation level
- 2.21 Maximum permissible modulation level
- 2.22 Minimum permissible modulation level
- 2.23 Maximum speed
- 2.24 Maximum permissible speed
- 2.25 Ramp-up curve / ramp-down curve
- 2.26 Limit speed
- 2.27 Potentiometer characteristic
- 2.28 Control limitation
- 2.29 Maximum power
- 2.30 Maximum coil current
- 2.31 Limiting speed for running monitor
- 2.32 Interface settings
- 2.33 Shedding function
- 2.34 Relay dropout delay
- 2.35 Fail safe function on/off
- 2.36 Fail safe function set value
- 2.37 Fail safe function time lag
- 2.38 Fail safe function running direction
- 2.39 Potentiometer characteristic limiting value for cable break
- 2.40 Sensor
- 2.41 Customer data
- 2.42 Error history
- 2.43 Reference value of DC-link voltage
- 2.44 Reference value of DC-link current
- 2.45 Production data
- 3 Input Register
- 3.1 Overview
- 3.2 Identification
- 3.3 Maximum number of bytes
- 3.4 Software name of bus controller
- 3.5 Software version of bus controller
- 3.6 Software name of commutation controller
- 3.7 Software version of commutation controller
- 3.8 Actual speed
- 3.9 Motor status
- 3.10 Warning
- 3.11 DC-link voltage
- 3.12 DC-link current
- 3.13 Module temperature
- 3.14 Motor temperature
- 3.15 Interior electronics temperature
- 3.16 Current direction of rotation
- 3.17 Current modulation level
- 3.18 Current set value
- 3.19 Sensor actual values
- 3.20 Current parameter set
- 3.21 Current power
MODBUS parameters "ebm-papst series 84 / 112 / 150 / 200"
_______________________________________________________________________________________
ebm-papst Mulfingen GmbH & Co. KG
Bachmühle 2 ·74673 Mulfingen, Germany ·Phone: +49 (0) 7938/81-0 ·Fax: +49 (0) 7938/81-110 ·www.ebmpapst.com ·info1@de.ebmpapst.com
DocNo.: 634505DocNo.: 446144DocNo.:358982DocNo.:322523DocNo.:309753DocNo.:303997DocNo.:276241DocNo.:256078DocNo.:196392 ·Template: 2 dated 6 October 2003 ·File: ext001157859.doc ·Last printed 10/03/2015 15:13:00
·Page 27 of 70
Form 1003
MODBUS
address
Designation
Write
ebm-papst
Write
customer
Write
end customer
Default
address
Cust. setting
address
D19F
Error history timing
D1A0
Reference value of DC-link voltage
X
-
-
-
-
D1A1
Reference value of DC-link current
X
-
-
-
-
D1A2
D1A3
Fan serial number
X
-
-
-
-
D1A4
Fan production date
X
-
-
-
-
D1A5 -
D1AA
Fan type
X
-
-
-
-
D1AB -
D1AC
Reserved
X
-
-
-
-
D1AD -
D1AE
Reserved
X
-
-
-
-
D1AF
Reserved
X
-
-
-
-
D1B0
Reserved
X
-
-
-
-
D1B1
Reserved
X
-
-
-
-
D1B2
Reserved
X
-
-
-
-
D1B3
Reserved
X
-
-
-
-
D1B4 -
D1B5
Reserved
X
-
-
-
-
D1B6
Reserved
X
-
-
-
-
D1B7
Reserved
X
-
-
-
-
D1B8 -
D1BF
Reserved
X
-
-
-
-
D1C0 -
D1C1
Reserved
X
-
-
-
-
D1C2 -
D1E6
No function
X
-
-
-
-
D1E7
Reserved
X
-
-
-
-
D1E8
Reserved
X
-
-
-
-
D1E9
Reserved
X
-
-
-
-
D1EA -
D1F8
Vacant
X
-
-
-
-
D1F9 -
D1FF
No function
X
-
-
-
-
D300 -
D340
No function
X
-
-
-
-
D341 -
D35F
Vacant
X
-
-
-
-
D360 -
D37F
Reserved
X
-
-
-
-
D380 -
D3FF
Vacant
X
-
-
-
-
*)
only in part
"No function" parameters have no influence on functionality in the Lite version.
These parameters are only defined for the non-Lite version.
Encoding of parameters:
Unless specified otherwise, parameters are encoded in "big endian" format, i.e. the byte with the
highest-value bits comes first. This is particularly true for parameters that include multiple holding
registers.