Installation Guide

ManualsBrandsSymmons ManualsPlumbingIdentity 2-Handle Tub and Shower Faucet Trim Kit with Hand Shower in Matte Black

1

2

3

4

5

6

7

Identity

™

Model Numbers

Identity Trim Series

Identity Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

6700-TRM

Shower Valve Trim

6701-TRM

Shower Trim

6702-TRM

Tub/Shower Trim

6703-TRM

Hand Shower Trim

6705-TRM

Shower/Hand Shower Trim

6706-TRM

Tub/Shower/Hand Shower Trim

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete warranty information.

Go to www.symmons.com/register to register your Symmons product.

TRIM, TA-10, T-12A

6700TRMTC

Shower Valve Trim

6701TRMTC

Shower Trim

6702TRMTC

Tub/Shower Trim

6703TRMTC

Hand Shower Trim

6705TRMTC

Shower/Hand Shower Trim

6706TRMTC

Tub/Shower/Hand Shower Trim

Warranty

6700-TRM

6700TRMTC

6701-TRM

6701TRMTC

6702-TRM

6702TRMTC

6705-TRM

6705TRMTC

6703-TRM

6703TRMTC

6706-TRM

6706TRMTC

TA-10T-12A

Summary of content (8 pages)

PAGE 1
Identity™ Identity Trim Series Identity Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A 6700-TRM Shower Valve Trim 6700TRMTC Shower Valve Trim 6701-TRM Shower Trim 6701TRMTC Shower Trim 6702-TRM Tub/Shower Trim 6702TRMTC Tub/Shower Trim 6703-TRM Hand Shower Trim 6703TRMTC Hand Shower Trim 6705-TRM Shower/Hand Shower Trim 6705TRMTC Shower/Hand Shower Trim 6706-TRM Tub/Shower/Hand Shower Trim 6706TRM
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (2mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions FIGURE 2 A P Measurements A B B C Q D R S C E F G H I D J K F E G T O L M H U J I K L M V N FLOOR Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater. 3) All dimensions measured from nominal rough-in (see I as reference).
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system. 1 PACKING NUT Replacement Parts Description Part Number FIGURE 3 4.
PAGE 4
7. Parts Breakdown FIGURE 7 C Item B O G A P N F L M E A B C D E F G H I J K K1 D F H E J Q L M N O P Q I K Showerhead Shower Arm Flange Handle Assy. Dome Cover Diverter Escutcheon Screws Shower Escutcheon Screws Mounting Plate Tub Spout Diverter Tub Spout Wall Cradle Screws Mounting Plate Hand Shower Wall Elbow 60" Hose 672SH 300S RTS-084 T-19 67-DIV-ESC 6700-ESC 060 054 EF-106 EF-100 EF-105 RTS-045 Notes: 1) Append appropriate suffix for premium finish.
PAGE 5
8. Installation - Shower Valve Trim 1) Secure large mounting plate to Temptrol pressure balancing valve using mounting screws (FIGURE 8.1). FIGURE 8.1 FIGURE 8.2 2) Secure large shower escutcheon to mounting plate. Tabs should snap in place (FIGURE 8.2). 3) Install dome cover by turning clockwise (FIGURE 8.3). 4) Install handle to shower valve. Secure with set screw (FIGURE 8.4). FIGURE 8.3 FIGURE 8.4 9.
PAGE 6
11. Installation - Slide Bar Assembly 1) Place mounting plate in position. Mark and drill 3/16" holes for tile anchors, 5/16" holes for drywall anchors. Install anchors (FIGURE 11.1). Note: For dry wall 1/2" thick or less, insert anchor tool into drywall anchor to secure behind wall prior to installing wall cradle. 1 FIGURE 11.1 1 2) R emove cover of hand shower cradle. Install cradle and mounting plate. Secure with three screws. Replace cover on hand shower cradle (FIGURE 11.2).
PAGE 7
12. Operation (Temperature Control) 1) Turn shower handle counter-clockwise approximately 1/4 turn to put valve in cold position (FIGURE 12.1). FIGURE 12.2 FIGURE 12.3 FIGURE 13.2 FIGURE 13.3 FIGURE 14.1 FIGURE 14.2 FIGURE 14.3 FIGURE 14.4 FIGURE 14.5 FIGURE 14.6 FIGURE 12.1 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 12.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 12.3). 13.
PAGE 8
15. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.