Visit us at www.swisherinc.com OWNER’S MANUAL MODEL NO. Trim-N-Mow STARTING SERIAL # L212-291001 ST67522BS ST67522BS-TSC DST67522BS Trim-Max IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment.
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of two (2) years from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship.
Safety Instructions This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. • • • • • • • • • • • • • • • • • • • • • • Read, understand and follow all instructions in the manual and on the trimmer before starting. Read this manual carefully. Become familiar with the controls and how to operate the unit properly.
Slope Operation Slopes are a major factor related to loss of control and slip accidents, which can result in severe injury. All slopes require extra caution. If you feel uneasy on it do not trim it. • • • • • • DO: Trim across the face of a slope and not up and down. DO: Remove objects such as rocks, tree limbs, etc. DO: Watch for holes, ruts or bumps. Tall grass can hide obstacles. DO NOT: Mow near drop-offs, ditches or embankments. The operator could lose footing or balance.
The operation of any mower can encounter foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before starting any cutting machine and while operating such a machine. The operation of any mower produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children.
Assembly Contents of Box: • Trimmer Parts bag containing: • Manual • Engine manual • Safety goggles • Bottle of engine oil • 2 sets of .155 trimmer line • Cable Clip Tools Required: • ½” wrench Handle Adjustment Installation of handles: • Remove loose fasteners from lower handles. • Pivot handles up and align lower hole in handles with hole on trimmer frame. Install hardware removed in previous step. Snug, but do not tighten bolts. • Pivot upper handles to fit the lower handles. Tighten knobs.
Preparing Unit For First Use • • • Fill engine crankcase with oil. A bottle has been provided with this unit. DO NOT OVERFILL. Fill the engine fuel tank with gasoline. GASOLINE SHOULD BE ADDED OUTSIDE IN A WELL-VENTILATED AREA. Check to ensure string has been installed properly. A diagram is provided just above the wheel for proper installation. Operation Important! To ensure proper operation, clean the engine and trimmer regularly. Remove any build up of chaff from the top of the engine.
Installing Trimmer Line Important! Use the proper length of line. Using a line too long for the unit will cause stalling and unacceptable operation. Use 18” Trimmer Line Part Number P3618 • • • • Step 1 Loosely fold trimmer line in half. (1) Place loop of line against outside of loop on the trimmer head. (2) Bring ends around and through the loop and over the cutter line loop. (3) Pull ends to tighten loop.
Trimmer Maintenance Make sure your trimmer is in safe working condition by keeping the following guidelines in mind every time you use your trimmer. • • • • • • • • • • Keep trimmer in good operating condition and keep all guards and shields in place. DO NOT operate this trimmer if any of the shields and guards are missing. Check all fasteners for secure fit to keep equipment in safe working order. Make adjustments as necessary.
Trim-N-Mow ST67522BS ST67522BS-TSC Item # Description 1 Briggs & Stratton Engine 2 Nut - Serrated Flange 5/16-18 3 Bolt - Serrated Flange, 5/16-18 X 2 1/4 4 Pulley - Engine 5 Washer - SP Bellville 6 Bolt - HHC 3/8-24 X 1 7 Cable - Operator Presence 8 Bolt - Serrated Flange, 5/16-18 X 1 1/4 9 Knob - Black Plastic 10 Washer - SAE Flat 5/16 11 Handle - Bail 12 Handle - Upper 13 Bolt - Carriage, 5/16-18 X 1 3/4 14 Handle - Lower When ordering replacement parts * USE PAINT CODE: TK=BLACK Part # N/A NB170 NB622
Trimmer Head Assembly for Trim-N-Mow Item # Qty. Part # 1 1 NB595 2 1 2049 3 2 NB149 4 2 B985/8 5 1 18846 6 1 18849* 7 1 NB586 8 1 2021* 9 1 NB598 10 1 2035 11 1 2042 12 2 10177 13 3 26x249 14 1 NB181 15 2 15748* 16 1 17651* 17 1 NB106 When ordering replacement parts * USE PAINT CODE: TK=BLACK 11 Description Nut - 2 Way Locking Jam 5/8-11 Pulley - Blade 4.
Trimmer Head Assembly for Trim-Max Item # Qty Part # Description 1 1 NB595 Nut - Lock Jam, 5/8-11 2 1 2049 Pulley - Blade, 4.
Trim-Max DST67522BS SEE DETAIL PAGE 12 SEE DETAIL PAGE 12 Item # Description 1 Briggs & Stratton Engine 2 Nut - Serrated Flange 5/16-18 3 Bolt - Serrated Flange 5/16-18 X1 1/4 4 Pulley - Engine 5 Washer - SP Bellville 6 Bolt - HHC 3/8-24 X 1 7 Cable - Operator Presence 8 Bolt - Serrated Flange 5/16-18X2 1/4 9 Pivot - Handle Grip 10 Knob - Black Plastic 11 Washer - SAE Flat 5/16 12 Handle - Bail 13 Handle - Upper 14 Bolt - Carriage 5/16-18 X 1 3/4 15 Handle - Lower 16 Guard - Belt When ordering replacemen
Visit us at: www.swisherinc.com OWNER’S MANUAL MODEL NO. Each trimmer has its own model number. Each engine has its own model number. The model number for the trimmer will be found on the left hand side of the motor base. The model number for the engine will be found on the top of the blower fan housing. All trimmer parts listed herein may be ordered directly from Swisher or your nearest Swisher dealer. All engine parts may be ordered from the nearest dealer of the engine supplied with your mower.
Visítenos en www.swisherinc.com MANUAL DEL PROPIETARIO MODELO NO. Trim-N-Mow STARTING SERIAL # L212-291001 ST67522BS ST67522BS-TSC DST67522BS Trim-Max IMPORTANTE Lea y siga todas las advertencias e instrucciones sobre seguridad antes de poner en funcionamiento este equipo.
GARANTÍA LIMITADA La garantía que el fabricante otorga al comprador original es: Este producto está libre de defectos en los materiales y la mano de obra por un periodo de dos (2) años desde la fecha de compra por parte del comprador consumidor original. Repararemos o cambiaremos, a nuestra discreción, las partes que se determine estén defectuosas debido a los materiales o a la mano de obra.
Instrucciones sobre seguridad Este símbolo de alerta de seguridad indica mensajes importantes en este manual. Cuando vea este símbolo, lea cuidadosamente el mensaje que sigue y esté alerta a la posibilidad de lesiones personales • • • • • • • • • • • • • • • • • • • • • • • Lea, comprenda y siga todas las instrucciones del manual y sobre la orilladora antes de encenderla Lea cuidadosamente este manual. Familiarícese con los controles y cómo operar correctamente la unidad.
Funcionamiento en pendiente Las pendientes son un factor principal relacionado con la pérdida de control y de accidentes por resbalones, los cuales pueden ocasionar lesiones graves. Todas las pendientes exigen mayor precaución. Si se siente incómodo en una pendiente no realice la poda. • • • • • • SÍ: Pode a través de la cara de una pendiente y no arriba y abajo SÍ: Quite los objetos tales como rocas, ramas de árboles, etc. SÍ: Esté pendiente de los agujeros, los surcos o los topes.
Cuando está en funcionamiento, cualquier cortadora puede chocar con objetos extraños que podrían ser lanzados a los ojos, lo que podría causar lesiones graves. Siempre use lentes de seguridad certificados o gafas de seguridad de visión amplia sobre los anteojos, antes de fijar la vista en cualquier maquina cortadora y mientras esté operando tal máquina. El funcionamiento de cualquier cortadora produce ondas sonoras que pueden dañar el oído humano. Se recomienda protección para los oídos.
Ensamblaje Las cajas contienen: • Orilladora Contenido de las piezas en bolsas: • Manual • Manual del motor • Gafas de seguridad • Botella de aceite de motor • 2 juegos de línea cortadora de .155 • Sujetador de cable Herramientas necesarias: • Llave de 12,7 mm Ajuste del mango Instalación de los mangos • Quite los sujetadores sueltos de los mangos inferiores • Déle vuelta hacia arriba a los mangos y alinee el agujero inferior de los mangos con el agujero del marco de la orilladora.
Preparación de la unidad para uso por primera vez • Llene el cárter del motor con aceite. Con esta unidad se ha suministrado un envase con aceite. NO LO SOBRELLENE. • Llene el tanque de combustible del motor con gasolina. LA GASOLINA DEBE AGREGARSE EN EL EXTERIOR, EN UN ÁREA BIEN VENTILADA. • Inspeccione para estar seguro de que la cuerda se ha instalado correctamente.
Instalación de la línea recortadora ¡Importante! Use la longitud adecuada de la línea. El uso de una línea demasiado larga para la unidad, ocasionará atascamientos y mal funcionamiento. De 5 HP o más usan una cuerda de 45,7 cm Compre la línea pre cortada P3618 • • • • Paso 1 Paso 2 Doble con holgura la línea cortadora a la mitad. (1) Coloque el lazo de la línea contra la parte externa del lazo en la cabeza cortadora.
Mantenimiento de la orilladora • • • • • • • • • • • • • • Asegúrese de que la orilladora esté en buenas condiciones de trabajo, teniendo en mente las siguientes indicaciones cada vez que use su orilladora. Mantenga la orilladora en buenas condiciones de funcionamiento y conserve todos los protectores y pantallas en su lugar. NO opere esta orilladora si falta alguna de las pantallas o protectores.
Trim-N-Mow ST67522BS ST67522BS-TSC *Tabla de referencia de la pintura Color Código de la pintura Negro texturizado TK Art. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Descripción Pieza No.
Ensamblaje de la cabeza cortadora para la Trim-N-Mow *Tabla de referencia de la pintura Color Negro texturizado Código de la pintura TK Descripción # Cant. # de Parte Contratuerca de dos vías de 5/8-11 1 1 NB595 Polea de pala- 4.
Ensamblaje de la cabeza cortadora para el Trim-Max # Cant. # de Parte 1 1 NB595 2 1 2049 3 2 NB149 4 2 B985/8 5 1 2124 6 1 2110* 7 1 NB586 8 1 2021* 9 1 NB598 10 1 2035 11 1 2107* 12 1 2033 13 1 2043** 14 1 NB110** 15 2 NB275** 16 1 2084** 17 1 2042** 18 1 2030** 19 1 B19BLACK 20 1 2103A 21 1 NB210Z 22 1 2075 23 1 2068 24 1 NB170 25 1 NB181 26 1 NB594 27 1 NB173 28 1 2083 29 1 2078 Descripción Contratuerca de dos vías de 5/8-11 Polea de pala- 4.
Trim-Max *Tabla de referencia de la pintura Color Código de la pintura Negro texturizado TK VER DETALLE PÁGINA 12 VER DETALLE PÁGINA 12 Art. No.
Visítenos en: www.swisherinc.com MANUAL DEL PROPIETARIO MODEL NO. Cada orilladora tiene su propio número de modelo. Cada motor tiene su propio número de modelo. El número de modelo de la orilladora se encuentra en el lado izquierdo de la base del motor. El número de modelo del motor se encuentra en la parte superior de la caja del ventilador soplador. Todas las piezas de la orilladora listadas aquí se pueden ordenar directamente a Swisher o al distribuidor Swisher más cercano.