Instructions / Assembly

ManualsBrandsSwing-N-Slide Playsets ManualsKitchenPlayful Palace Wood Complete Playset

PB 8327

PB 8331

IMPORTANT!!

PLEASE READ BEFORE BEGINNING ASSEMBLY!!

Please make sure all lumber, hardware and accessory parts are accounted for.

If you are missing anything, please DO NOT RETURN to the store where purchased.

Please call our Customer Service Department at the number below.

NOTE:

SLIDE NOT INCLUDED

WITH PB 8327

LDR 02-28-2018

Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232

Summary of content (61 pages)

PAGE 1
PB 8327 PB 8331 NOTE: SLIDE NOT INCLUDED WITH PB 8327 IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased. Please call our Customer Service Department at the number below. Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232 © Swing-N-Slide Inc.
PAGE 2
5CHGV[ %JGEMNKUV HQT 5YKPIÄ0Ä5NKFG 2NC[ 5GVU CPF #EEGUUQTKGU 1DUGTXKPI VJG HQNNQYKPI UVCVGUOGPVU CPF YCTPKPIU TGFWEGU VJG NKMGNKJQQF QH UGTKQWU QT HCVCN KPLWT[ 6JKU RNC[UGV JCU DGGP FGUKIPGF HQT WUG D[ C OCZKOWO QH PKPG QEEWRCPVU CV QPG VKOG JCXKPI C EQODKPGF YGKIJV QH RQWPFU 6JKU RNC[UGV KU KPVGPFGF HQT WUG D[ EJKNFTGP HTQO VQ [GCTU QH CIG 1PÄUKVG CFWNV UWRGTXKUKQP HQT EJKNFTGP QH CNN CIGU KU TGEQOOGPFGF +PUVTWEV EJKNFTGP PQV VQ YCNM ENQUG VQ KP HTQPV QH DGJKPF
PAGE 3
2.#;5'6 /#+06'0#0%' %QUOGVKE FGHGEVU VJCV FQ PQV CHHGEV VJG UVTWEVWTCN KPVGITKV[ QH VJG RTQFWEV QT PCVWTCN FGHGEVU QH YQQF UWEJ CU YCTRKPI URNKVVKPI EJGEMKPI VYKUVKPI UJTKPMCIG UYGNNKPI QT CP[ QVJGT RJ[UKECN RTQRGTVKGU QH YQQF VJCV FQ PQV RTGUGPV C UCHGV[ JC\CTF CTG PQV EQXGTGF D[ QWT YCTTCPV[ 6Q JGNR OKPKOK\G VJGUG PCVWTCN FGHGEVU YG TGEQOOGPF CRRN[KPI C UGCNGT QT UVCKP GXGT[ VYQ QT VJTGG [GCTU QT OQTG QHVGP CU VJG ENKOCVG FKEVCVGU 2QYGT YCUJKPI UCPFKPI QT QVJGT RTGRCTCVQT[ OGVJQFU UJQWNF DG
PAGE 4
2.#;)4170& 574(#%+0) /#6'4+#.5 5'%6+10 1( 6*' %1057/'4 241&7%6 5#('6; %1//+55+105 176&114 *1/' 2.
PAGE 5
DIMENSIONS 6’ -0’’ 14’ -0’’ 14’ -4’’ 6’ -0’’ 28’ -0’’ 11’ -0’’ 6’ -0’’ 14’ -0’’ 6’ -0’’ 26’ -4’’ MINIMUM USE ZONE FOR PLAY EQUIPMENT SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF THE PLAY STRUCTURE. SWING USE ZONE EXTENDS NO LESS THAN 168”. SWINGS MUST HAVE A MINIMUM CLEARANCE OF 8” ABOVE THE PROTECTIVE SURFACING.
PAGE 6
TOOLS REQUIRED DRILL SCREWDRIVER 1/2” & 7/16’’ SOCKETS & WRENCH PHILLIPS BIT HAMMER CARPENTER SQUARE ADJUSTABLE WRENCH SAFETY GLASSES 1/8” DRILL BIT TAPE MEASURE PLIERS INCLUDED HARDWARE 3” Deck Screw (x9) 2-1/2” Deck Screw (x170) 5/16” Loc Nut (x10) 2” Deck Screw (x105) 5/16” Wood Loc Washer (x3) 3/16” Tarp Washer (x6) 1-3/4” Deck Screw (x155) 5/16” Washer (x39) 1-5/8” Deck Screw (x12 ) 1-1/4” Deck Screw (x210 ) 3/4” Flat Head Screw (x18 ) 1/4” x 1-3/4” Pan Screw (x2) #12 x 3/4” Pan Scr
PAGE 7
HARDWARE 1/4”-20 x 1-1/4” Hex Bolt (x12) 5/16”-18 x 1-3/4” Hex Bolt (x1) 5/16”-18 x 2” Hex Bolt (x2) 5/16”-18 x 2-1/2” Hex Bolt (x4) 5/16”-18 x 3-1/4” Hex Bolt (x2) 5/16”-18 x 3-1/2” Hex Bolt (x4) 5/16”-18 x 4” Hex Bolt (x7) 5/16”-18 x 7” Hex Bolt (x1) 5/16”-18 x 8-1/2” Hex Bolt (x1) 5/16”-18 x 6” Carriage Bolt (x3) 5/16”-18 x 3” Carriage Bolt (x1) 7 1/4 -18 T-Nut (x12) Small Steering Wheel Spacer (x1) 5/16” x 1-1/2” Lag Screw (x4)
PAGE 8
SA6366 BOX 1 of 2 BOARD LIST (2) [PF 6325] 3’’ x 3’’ x 94-1/4’’ (1) [PF 6309] 5/8’’ x 3-3/8’’ x 35’’ (2) [PF 6324] 3’’ x 3’’ x 94-1/4’’ (1) [PF 6331] 5/8’’ x 3-3/8’’ x 31-1/2’’ (1) [PF 6323] 3’’ x 3’’ x 31-1/2’’ TOWER BEAM SUPPORT (1) [PF 6338] 3/4’’ x 3-3/8’’ x 31-1/2’’ (1) [PF 6298] 2-11/16” x 3” x 62’’ SWING BEAM SUPPORT (1) [PF 6346] 5/8’’ x 3-3/8’’ x 31-1/2’’ (2) [PF 6303] 5/8’’ x 3-3/8’’ x 30’’ (1) [PF 6299] 2-5/8” x 5-3/8” x 93” SWING BEAM (2) [PF 6315] 1’’ x 3-3/8’’ x 53’’ (1) [PF 6314] 1’’ x
PAGE 9
SA6065 BOX 2 of 2 BOARD LIST (2) [PF 6297] 1-3/8’’ x 3-3/8’’ x 83’’ A-FRAME (20) [PF 6330] 1/2” x 3-5/16” x 36-3/4” SHINGLE (1) [PF 6296] 1-3/8’’ x 3-3/8’’ x 58’’ A-FRAME SUPPORT (2) [PF 6354] 5/8’’ x 3-3/8’’ x 37-3/8’’ (2) [PF 6352] 1-3/8’’ x 3-3/8’’ x 31-1/2’’ (3) [PF 6309] 5/8’’ x 3-3/8’’ x 35’’ (2) [PF 6295] 1-3/8’’ x 3-3/8’’ x 17-1/4’’ SLIDE STAKE (4) [PF 6308] 5/8’’ x 3-3/8’’ x 35’’ (2) [PF 6334] 1-3/8’’ x 3-3/8’’ x 8’’ (2) [PF 6320] 5/8’’ x 3-3/8’’ x 34-3/4’’ (2) [PF 6313] 1-3/8’’ x 3’’ x 77-
PAGE 10
COMPONENTS Swing Beam Bracket (x2) Window Pane (x1) Beam Brace (x1) Tarp (x1) Play Handle (x2) 58” Dipped Chain (x4) STD Swing Seat (x2) 5/16’’ x 5-1/2’’ Swing Hanger (x6) Steering Wheel (x1) PB 8327 PB 8331 NOTE: SLIDE NOT INCLUDED WITH PB 8327 IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased.
PAGE 11
COMPONENTS Beam Clamp Slotted (x6) Telescope (x1) Flag Assembly (x2) Iron Man Ring (x2) Anchor It Strap (x4) 33” Dipped Chain (x2) 11 Climbing Rock (x6) Trapeze Bar (x1) Anchor It (x4)
PAGE 12
STEP 1 PANEL A 2-3/8’’ SPACE Flush 8-3/8’’ Check to make sure structure is square PF 6354 5/8’’ x 3-3/8’’ x 37-3/8’’ 18-11/16’’ (4) PF 6309 5/8’’ x 3-3/8’’ x 35’’ 35-5/8’’ (4) 30mm Deck Screws Per Board 16-5/16’’ 5/8’’ 5-3/8’’ ! PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’ Install 30mm Screws With Heads Flushed To Board To Avoid Protrusions.
PAGE 13
STEP 2 2-3/8’’ SPACE PANEL C Flush PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’ Check to make sure structure is square (4) PF 6308 5/8’’ x 3-3/8’’ x 35’’ 35-5/8’’ (4) 30mm Deck Screws Per Board PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’ 5/8’’ 5-7/16’’ ! PANEL D Flush Install 30mm Screws With Heads Flushed To Board To Avoid Protrusions.
PAGE 14
STEP 3 Check to make sure structure is square (2) 2-1/2’’ Deck Screws 18-11/16’’ TO HOLES Flush T-Nut Small (2) 2-1/2’’ Deck Screws Flush (2) 2-1/2’’ Deck Screws Flush PANEL C (2) 2-1/2’’ Deck Screws T-Nut Small PF 632 53 ’’ x 3’’ x 941/4 ’’ (2) 2-1/2’’ Deck Screws NOTE: HOLE ORIENTATION PF 632 43 ’’ x 3’’ x 941/4 ’’ FRAME A Flush Flush (2) 2-1/2’’ Deck Screws PF ’’ -1/2 /2’’ 1 1 3 31 ’’ x -3/8 3 ’’ x 3/4 8 633 2-1/2” Deck Screw (x12) 1. Assemble Frame A as shown.
PAGE 15
STEP 4 (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’Loc-Washer 5/16’’ Washer PF 6314 1’’ x 3-3/8’’ x 31-1/2’’ FRAME A FLIP FRAME OVER 2-1/2” Deck Screw (x4) 1. Flip frame over and Attach Frame Support Board as shown above.
PAGE 16
STEP 5 (2) 2-1/2’’ Deck Screws (1) PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’ PF 6307 5/8’’ x 3-3/8’’ x 31-1/2’’ (2) PF 6310 5/8’’ x 3-3/8’’ x 8-5/16’’ PF 6307 5/8’’ x 3-3/8’’ x 31-1/2’’ T-Nut Small (2) 2-1/2’’ Deck Screws per Board This Side (2) 2-1/2’’ Deck Screws 3-1/2’’ PF 632 43 ’’ x Flush (2) 2-1/2’’ Deck Screws per Board This Side NOTE: HOLE ORIENTATION PF 632 53 ’’ x T-Nut Small 3’’ x 941/4 ’’ NOTE HOLES FRAME B 3’’ x 941/4 ’’ (2) 2-1/2’’ Deck Screws ’’ 335 62-1/2 6 PF 8’’ x -3/ x3 ’ ’ 4
PAGE 17
STEP 6 (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’Loc-Washer 5/16’’ Washer PF 6314 1’’ x 3-3/8’’ x 31-1/2’’ FRAME B FLIP FRAME OVER 2-1/2” Deck Screw (x4) 1. Flip frame over and Attach Frame Support Board as shown above.
PAGE 18
STEP 7 Flush Check to make sure structure is square 3’’ From Outside of Post Flush PF 635 45 /8’’ x (3) 2-1/2’’ Screws 3’’ From outside of post To end of horizontal support.
PAGE 19
STEP 8 Flush (3) 2-1/2’’ Screws Flush 3’’ From Outside of Post (5) 2-1/2’’ Screws FRAME A 3’’ From Outside of Post to End of Horizontal Support. (2) 2-1/2’’ Screws FRAME B Side View of Tower 19-1/2’’ From Outside of Post (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws 2-1/2” Deck Screw (x16) 1. Attach Frame B to Frame A as shown.
PAGE 20
STEP 9 (2) 2-1/2’’ Screws PF 6346 5/8’’ x 3-3/8’’ x 31-1/2’’ (2) 2-1/2’’ Screws NOTE: HOLE LOCATION 2-1/2” Deck Screw (x4) 1. Attach Tower Support Board as shown.
PAGE 21
STEP 10 5/16-18 X 4’’ Hex Head Bolt 5/16’’Loc-Washer 5/16’’ Washer (2) 2-1/2’’ Screws T-Nut Small PF 6352 1-3/8’’ x 3-3/8’’ x 31-1/2’’ 46-5/8’’ 2-1/2” Deck Screw (x4) 1. Attach Frame Support Board as shown.
PAGE 22
STEP 11 Flush (4) 2-1/2’’ Screws (1) 2’’ Screw per side (1) PF 6312 1-3/8’’ x 1-3/8’’ x 31-1/2’’ (1) PF 6346 5/8’’ x 3-3/8’’ x 31-1/2’’ Back of Tower Flush 55-1/4’’ (1) 2’’ Screw per side PF 6305 5/8’’ x 3-3/8’’ x 25-3/8’’ (6) 1-3/4’’ Screws PF 6305 5/8’’ x 3-3/8’’ x 25-3/8’’ (6) 1-3/4’’ Screws (1) PF 6346 5/8’’ x 3-3/8’’ x 31-1/2’’ NOTE: PRE-DRILL HOLES GOING INTO DECK SUPPORTS (4) 2-1/2’’ Screws 11’’ 11’’ Top View of Tower 2-1/2” Deck Screw (x8) 2” Deck Screw (x2) 1-3/4” Deck Screw (x12)
PAGE 23
STEP 12 (7) PF 6306 5/8’’ x 3-3/8’’ x 31-3/8’’ (6) 1-3/4’’ Screws per board Flush Flush (2) 2-1/2’’ Screws per joint Flush 2-1/2” Deck Screw (x8) PANEL B PANEL B INSTALL 1-3/4” Deck Screw (x42) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 1/8’’. 2. Install Panel B as shown.
PAGE 24
STEP 13 (8) 1-1/4’’ Screws PF ’’ x 3/4 5 633 (4) 2-1/2’’ Screws INSIDE VIEW (4) 2-1/2’’ Screws 3-3 /8’’ x NOTE HOLE LOCATION 77-1/4’’ Flush PF 633 15 /8’’ x ’’ 1/2 62x /8’’ 3-3 311/2 ’’ 26’’ 1-1/4” Deck Screw (x8 ) 2-1/2” Deck Screw (x8) 1. Attach Barrier Support Board and Safety Board as shown. NOTE: Secure Barrier Board from inside barrier as shown.
PAGE 25
STEP 14 NOTE: MAKE SCREW (2) 1-5/8’’ Screws T-Nut Small HEADS FLUSH 5/16’’Loc-Washer 5/16’’ Washer 5/16-18 X 1-3/4’’ Hex Head Bolt (2) 3’’ Screws PF 6326 1’’ x 3-3/8’’ x 42’’ SUPPORT 3” Deck Screw (x2) 1-5/8” Deck Screw (x2 ) 1. Attach Tower Support Board as shown.
PAGE 26
STEP 15 (2) 1-3/4’’ Screws (2) 1-3/4’’ Screws Flush PANEL D Flush 1-3 PF /8’’ x 3 6313 ’’ x 771/4 ’’ Flush (2) 1-3/4’’ Screws ! NOTE: 5/8’’ Offset to Bottom 1-3 PF /8’’ x 3 6313 ’’ x 771/4 ’’ (2) 1-3/4’’ Screws FRAME C COUNTERBORE 45 ’’ T O 46 -5/ 8’’ (2) 1-3/4’’ Screws Flush HO LE Flush (2) 1-3/4’’ Screws FLIP FRAME OVER PF /8’’ 3-3 x /4’’ 83 3 3 6 Flush /2’’ 1-1 3 x (2) 2’’ Screws T-Nut Small 5/16’’ Washer 5/16’’Loc-Washer 5/16-18 X 2-1/2’’ Hex Head Bolt LIFT FRAME UP PF 6352 1-3/
PAGE 27
STEP 16 Check to make sure structure is square (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws ’ /8’ 5 29 FRAME C (2) 2-1/2’’ Screws 2-1/2” Deck Screw (x6) 1. Attach Frame C to Tower as shown.
PAGE 28
STEP 17 NOTE: PANEL D NOT SHOWN FOR CLARITY. Flush (2) PF 6349 5/8’’ x 3-3/8’’ x 29-1/2’’ (6) 1-3/4’’ Screws per board (6) 1-3/4’’ Screws per board PF 6312 1-3/8’’ x 1-3/8’’ x 31-1/2’’ Flush NOTE: PRE-DRILL HOLES GOING INTO DECK SUPPORTS 12-3/4’’ 12-3/4’’ Top View of Tower 1-3/4” Deck Screw (x12) 1. Attach Deck Boards and Deck Support Board as shown.
PAGE 29
STEP 18 NOTE: PANEL D NOT SHOWN FOR CLARITY. Flush (7) PF 6348 5/8’’ x 3-3/8’’ x 30-7/8’’ (6) 1-3/4’’ Screws per board 1-3/4” Deck Screw (x42) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 1/8’’.
PAGE 30
STEP 19 NOTE: PANEL D NOT SHOWN FOR CLARITY. PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’ \ 2-1/4’’ (4) 2-1/2’’ Screws Flush 2-1/2” Deck Screw (x4) 1. Attach Spacer Board as shown.
PAGE 31
STEP 20 PF 6323 3’’ x 3’’ x 31-1/2’’ TOWER BEAM SUPPORT 5/16-18 X 6’’ Carriage Bolt Wood Loc-Washer 5/16’’ Washer Loc Nut 1. Attach Tower Beam Support Board as shown.
PAGE 32
STEP 21 PF 6299 2 5/8’’x 5-3/8’’x 93’’ Swing Beam 5/16’’ T-Nut Large 5-1/2’’ Swing Hanger Beam Clamp 2 1 x4 Correct Orientation 4 (4) 1-1/4’’ Deck Screws 5 1. Attach Swing Hanger(s) to swing beam as shown.
PAGE 33
STEP 22 PF 6298 2-11/16’’x 3’’x 62’’ A-Frame SB Support 5/16”-18 x 7” Hex Head Bolt (1) 3’’ Screws (1) 3’’ Screws 5/16” Washer 5/16” Washer 5/16” Loc Nut (2) PF 6297 1-3/8’’x 3-3/8’’x 83’’ A-Frame 5/16”-18 x 2-1/2” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 5/16” Washer 5/16” Loc Washer (2) 2-1/2’’ Screws 5/16”-18 x 4” Hex Head Bolt (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws 5/16-18 T-Nut Small PF 6296 1-3/8’’x 3-3/8’’x 58’’ A-Frame Support 5/16-18 T-Nut Small 3” Deck Screw (x2)
PAGE 34
STEP 23 (2) Swing Beam Bracket 5/16”-18 x 3-1/2” Hex Head Bolt x2 5/16” Washer 5/16” Loc Nut 5/16”-18 x 3-1/2” Hex Head Bolt 5/16” Washer x2 5/16” Washer 5/16” Washer 5/16” Loc Nut 1. Attach Swing Beam Bracket to A-Frame & Swing Beam as shown.
PAGE 35
STEP 24 5/16”-18 x 3 1/4” Hex Head Bolt Beam Brace 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 1. Install Swing Beam Brace as shown.
PAGE 36
STEP 25 5/16”-18 x 8-1/2” Hex Head Bolt 5/16”-18 x 6” Carriage Bolt 5/16” Loc Washer 5/16” Washer 5/16” Wood Loc Washer 5/16-18 T-Nut Small 5/16” Washer 5/16” Loc Nut 1. Install Swing Beam as shown.
PAGE 37
STEP 26 (2) 2-1/2’’ Screws per board NOTE: Window Panel Removed for Clarity. 2-1/2” Deck Screw (x8) 1. Secure Barrier Boards to Swing Beam Support as shown.
PAGE 38
STEP 27 PF 6342 5/8’’ x 3-3/8’’ x 7’’ PF 6344 5/8’’ x 3-3/8’’ x 5-3/8’’ (2) 1-3/4’’ Screws Flush (2) 1-3/4’’ Screws 1-3/4” Deck Screw (x4) $WWDFK %DUULHU 6XSSRUW %RDUGV ÀXVK WR ERWWRP RI GHFN DV VKRZQ 38
PAGE 39
STEP 28 ! Install 30mm Screws With Heads Flushed To Board To Avoid Protrusions. (2) PF 6303 5/8’’ x 3-3/8’’ x 30’’ (4) 30mm Screws per board Flush ! 1-3/16’’ 30mm Deck Screw (x8) 1. Attach barrier boards as shown.
PAGE 40
STEP 29 (1) 3’’ Screw (2) 30mm Screws NOTE: LOOK FOR PRE-DRILLED HOLE 5/16’’ PF 6321 5/8’’ x 3-3/8’’ x 6-3/4’’ SUN 5/16’’ CENTERED x2 PF 6319 5/8’’ x 2’’ x 28’’ 6-3/4’’ 6-3/4’’ (2) 1-1/4’’ Deck (2) 1-1/4’’ Deck Screws Screws PF 6351 1’’ x 3-3/8’’ x 29-1/8’’ PF 6350 1’’ x 3-3/8’’ x 26’’ x2 (2) 30mm Screws 1/2’’ Front View (3) 1-1/4’’ Deck Screws 1’’ OVERHANG (2) 1-1/4’’ Deck Screws per board (2) PF 6330 1/2’’ x 3-5/16’’ x 36-3/4’’ SHINGLE 1’’ OVERHANG (3) 30mm Screws (2) 1-1/4’’ Deck Screws
PAGE 41
STEP 30 NOTE: SHINGLES OVERHANG RAFTERS 1” NOTE: TURN ROOF ASSEMBLY ON END. CENTER AND CLAMP PF 6355 BEFORE INSTALLING SCREWS.
PAGE 42
STEP 31 (3) 1-1/4’’ Deck Screws (2) PF 6330 1/2’’ x 3-5/16’’ x 36-3/4’’ SHINGLE (2) 2’’ Deck Screws (5) 1-1/4’’ Deck Screws per board PF 6320 5/8’’ x 3-3/8’’ x 34-3/4’’ PF 6320 5/8’’ x 3-3/8’’ x 34-3/4’’ (4) 2’’ Deck Screws (4) 2’’ Deck Screws 2” Deck Screw (x8) 1-1/4” Deck Screw (x22) 1. Attach roof as shown. 2. Attach (2) shingles. 3. Attach (2) end roof boards.
PAGE 43
STEP 32 ALIGN SCREWS WITH PRE DRILLS Flush (3) 2-1/2’’ Deck Screws Per side PF 6315 1’’ x 3-3/8’’ x 53’’ ROCK WALL SIDE PF 6315 1’’ x 3-3/8’’ x 53’’ ROCK WALL SIDE (5) PF 6341 5/8’’ x 5-3/8’’ x 26-7/8’’ Flush Side View Top (4) 2’’ Deck Screws per board (1) PF 6340 5/8’’ x 5-3/8’’ x 26-7/8’’ 2-1/2” Deck Screw (x6) 2” Deck Screw (x24) 1. Align and install rock wall boards to the image above. 2.
PAGE 44
STEP 33 (1) PF 6341 5/8’’ x 5-3/8’’ x 26-7/8’’ (4) 2’’ Deck Screws Flush (2) 2’’ Deck Screws (2) 2’’ Deck Screws (1) PF 6353 5/8’’ x 3-3/8’’ x 3’’ Side View Bottom 2” Deck Screw (x6) 1. Attach rock wall board and spacer as shown.
PAGE 45
STEP 34 (2) Weld Nuts (2) 1-1/4’’ Hex Head Bolts (2) 1/4’’Flat Washer Per Rock (2) 1/4’’ Loc-Washer Per Rock 1. Attach Climbing Rocks as shown.
PAGE 46
STEP 35 PF 6303 5/8’’ x 3-3/8’’ x 30’’ (4) 2’’ Screws Flush 23’’ 2-5/8’’ 2-5/8’’ (2) 30mm Screws ! (2) 1-1/4’’ Screws 1-3/16’’ 30mm Deck Screw (x12) (6) PF 6327 5/8’’ x 3-3/8’’ x 23’’ Inside View 1-1/4” Deck Screw (x12) 1. Attach Barrier Board and attach barrier as shown.
PAGE 47
STEP 36 NOTE HOLE PF 6311 3/4’’ x 5-3/8’’ x 21-1/2’’ 1-7/8’’ NOTE HOLES 5’’ 9-5/8’’ (2) PF 6329 1’’ x 3-1/4’’ x 4-5/8’’ TABLE SUPPORT (4) 1-5/8’’ Screws 2’’ (3) 1-3/4’’ Screws 2’’ (1) 1-5/8’’ Screws per board Top View of Table 1-5/8” Deck Screw (x6) 1-3/4” Deck Screw (x3) 1. Assemble Table and attach to barrier as shown.
PAGE 48
STEP 37 (2) PF 6302 3/4’’ x 3-3/8’’ x 9-3/4’’ TABLE SUPPORT (2) PF 6300 3/4’’ x 3-3/8’’ x 15-3/4’’ BENCH SUPPORT (4) 1-1/4’’ Screws (4) 1-1/4’’ Screws 3’’ (8) 2-1/2’’ Screws 3’’ Flush 11-3/8’’ 13-3/4’’ Flush 6-7/8’’ 6-7/8’’ 25’’ (2) PF 6301 3/4’’ x 3-3/8’’ x 26-7/8’’ PICNIC TABLE LEG Check to make sure structure is square (4) 2’’ Screws (2) PF 6328 5/8’’ x 3-3/8’’ x 28-1/2’’ TABLE (4) 2’’ Screws (2) 2’’ Screws 1-1/2’’ BOTH SIDES PF 6322 1’’ x 5-3/8’’ x 28-1/2’’ BENCH 1-1/2’’ BOTH SIDES 1-1
PAGE 49
STEP 38 PF 6333 3/4’’ x 3-3/8’’ x 15-1/2’’ (2) 2’’ Screws PF 6333 3/4’’ x 3-3/8’’ x 15-1/2’’ PF (2) 2’’ Screws ’’ 3/4 6 1 63 ’’ x -3/8 x3 ’ 24’ Flush Make Certain This Side Has Holes Closest To The Edge. Flush (2) 2’’ Screws per side (2) PF 6332 3/4’’ x 3-3/8’’ x 13’’ ARCH 33-1/2” To Bottom of Support 2” Deck Screw (x8) 1. Assemble Tarp Frame and Attach Supports to tower as shown.
PAGE 50
STEP 39 Flush (2) 2’’ Screws per side (1) 3’’ Screw (1) 3’’ Screw 2” Deck Screw (x4) 3” Deck Screw (x2) 1. Attach Tarp Support Frame to tower as shown.
PAGE 51
STEP 40 FLAP UP PF 6331 5/8’’ x 3-3/8’’ x 31-1/2’’ CENTERED (3) 3/4’’ Screws (3) 3/16’’ Tarp Washer (2) 2-1/2’’ Screw per joint 1-1/2’’ (3) 3/4’’ Screws (3) 3/16’’ Tarp Washer (3) 3/4’’ Screws (3) 3/16’’ Tarp Washer Tarp Side View 3/4” Pan Head Screw (x6) 2-1/2” Deck Screw (x4) 3/16” Tarp Washer (x6) 1. Attach tarp to support board as shown, wrapping around underneath the board, 2. Attach the support board to the tower so that the tarp is sandwiched between board and barrier. 3.
PAGE 52
STEP 41 (2) PF 6334 1-3/8’’ x 3-3/8’’ x 8’’ Flush Flush (8) 1-3/4” Deck Screws Underdeck View (3) 1-3/4” Truss Screws Grade 2” (2) 1-1/4 Deck Screws 1-3/4” Deck Screw (x8) 1-1/4” Deck Screw (x2) PF 6295 1-3/8’’x3-3/8’’x17-1/4’’ Slide Stake 1. Attach slide as shown.
PAGE 53
STEP 42 (2) 1/4” Washer (2) 1/4’’ x 1-3/4” Pan Screw 11” 1-3/4” Pan Screw (x4) 1. Attach Safety Handles and I.D. Tag as shown.
PAGE 54
STEP 43 1 2 3 4 NOTE: Crimp swing hanger tightly closed Ring-Trap Combo Assembly 1. Attach Quick Link to chain oriented as shown. 2. Attach Quick Link to gym ring as shown. Attach second set of Quick Links (3) links up. Attach Trapeze Bar as shown. 3. Tighten all Quick Links closed with wrench.
PAGE 55
BOTTOM OF SEAT BOTTOM OF SEAT STEP 44 Swing Seat Assembly 1. Take one length of chain and place the outermost link of chain through the Quick Link as shown. 2. Place the Quick Link through the Grommet of the swing seat as shown. 3. Tighten the threaded sleeve of the Quick Link with a suitably sized wrench so that the seat is securely attached and the Quick Link cannot be easily loosened. Repeat for second chain, Quick Link and Swing Seat Grommet.
PAGE 56
STEP 45 Carriage Bolt Spacer Flat Washer Loc Nut Steering Wheel Cap Steering Wheel Assembly 1. Choose a desired location for the Steering Wheel and drill a 5/16” diameter hole through the lumber. NOTE: If lumber is greater than 2” in depth, you will need to counterbore the hole appropriately. 2. Mount Steering Wheel to climbing unit as indicated. 3. Snap Steering Wheel cap into place.
PAGE 57
STEP 4600 Telscope Assembly Mounting Screw Mounting Bracket Telescope Assembly 1. Position Mounting Bracket in desired location. 2. Attach Mounting Bracket to the unit using the Mounting Screw provided. 3. Insert the Telescope into the Mounting Bracket as shown. STEP 46 (4) 3/4’’ Screws Per Flag (4) 3/4’’ Screws Per Flag 3/4” Flat Head Screw (x4 ) Flag Assembly 1. Secure Flags as shown.
PAGE 58
STEP 47 Fold up 5/16” Washer Anchor-It Strap 1-1/2” Lag Screw Anchor-It 5/16’’ x 1-1/2” Lag Screw (x4) 3ODFH VZLQJ VHW LQ ¿ QDO ORFDWLRQ DQG PRXQW $QFKRU ,W V DW ORFDWLRQV FLUFOHG DERYH 2. Twist the Anchor-It into the ground until only the loop is exposed. 3. Place Anchor-It Strap thru loop, fold the ends together and attach to the unit as shown. Note: Keep as little play as possible using any of the holes in the strap that work best.
PAGE 59
Warranty and Registration LA 9081 LDR 10-17-2016 Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY Swing-N-Slide® WDNHV JUHDW SULGH LQ WKH TXDOLW\ DQG GXUDELOLW\ RI RXU SURGXFWV 2XU 0DQXIDFWXUHU¶V /LPLWHG :DUUDQW\ SURYLGHV FRQ¿ GHQFH DQG demonstrates our commitment to providing quality residential playground products.
PAGE 60
PRODUCT WARRANTY & REGISTRATION Please register online to properly initiate your product warranty & registration %HQH¿WV RI UHJLVWHULQJ RQOLQH Ŷ Quick & simple from home or mobile Ŷ Record your purchase in our system Ŷ Initiate product warranty Ŷ Improved customer support Ŷ 1RWL¿FDWLRQ RI QHZ SURGXFW LQIRUPDWLRQ Register your product online at www.OnlineWarranty.
PAGE 61
Got Questions? We’ve got answers! Call our Customer Support Representatives 1-800-888-1232 Available Monday - Friday, 7am - 5pm (CST) Weekend support available April through July Technical support from experienced customer service representatives who have actually built a swing set themselves. @ Swing-N-Slide Inc.