TO BE REMOVED FOR USE BY OCCUPANT Laundry Tubs MF-1F (Single Bowl, Floor Mount Metal Legs) MF-1PF (Single Bowl, Floor Mount Plastic Legs) MF-1W (Single Bowl, Wall Mount) Product Warnings Safety Guidelines General Information Installation Procedure Cleaning & Maintenance Warranty Information MF-2W (Double Bowl, Wall Mount) MF-4PF (Single Bowl, Floor Mount Plastic Legs) MF-4W (Single Bowl, Wall Mount) R ea B da ef n or d e Un In d st er al s lin ta g nd MF-2F (Double Bowl, Floor Mount Metal
Safety Guidelines IMPORTANT NOTICE The Swan Assurance — if our product is properly installed and maintained, as stated in these instructions, it will not leak. IMPORTANT NOTICE: Indicates that equipment or property damage can result if instructions are not followed. Remember – Safety First Read and Understand the Manual It is the responsibility of any individual who installs or maintains this product to fully understand and follow proper installation and maintenance procedures.
Safety Guidelines General Information Personal Protection Be sure to use all personal protective equipment, such as sturdy work boots, preferably with steel toes, gloves, and hard hat, if necessary, to ensure your own safety. To prevent possible damage to your hearing, always wear ear protection, such as earmuffs or earplugs, when working around power tools. Electrical Shock Hazard Contacting live electrical wiring with power tools or hand tools can cause serious injury or death.
General Information General Information Installation Procedure Installation Procedure Contents (Wall Mount Units) Laundry Tub Contents (Wall Mount Units) Please use the model number located on the side of the when with questions on concerning the box Please usecontacting the model modelus number Please use the number located located on the the side side of of the the installation of this product.
Installation Procedure 1b. Attach Filler Brackets and Wall Mount — MF-1W and MF-2W (Single and Double Bowl Models) MF-4W (Single Bowl Model) 1. Place the laundry tub upside down on a flat surface. Protect the top edges of the laundry tub from scratches or other damage by placing cardboard or other scratch resistant material on the floor. LT-001 2. 2. Slide the metal or plastic leg into one of the plastic corner Slide the metal legininto of the cornertub.
Installation Procedure 2. Attach Wall Mounting Plate Note: Trial fit the wall mounting plate to the laundry tub. If the mounting plate is too long, break off the left side of the wall mounting plate by snapping it along the plate’s scored ridge. 2a. Attach Wall Mounting Plate to Framed Walls 1. Locate the rough position of the laundry tub and then locate the wall studs. The mounting plate must be attached using at least three screws. LT-024 3.
Installation Procedure 2c. Attaching Wall Mounting Plate to Concrete or Block Walls with Tapcon Wall Anchors (User Supplied) WARNING Oversized pilot holes may make it impossible to properly set the anchor and will reduce the anchor's load (holding) capacity. This reduced holding capacity can result in the anchor pulling free from the wall, resulting in possible personal injury or even death. 2. 1. Locate the wall mounting plate in the same manner as with wood construction.
Installation Procedure 3. 4. Final Installation If replacing an existing laundry tub, loosen and remove the hot and cold water lines and waste pipe connections. Use a container to catch any water remaining in the P-trap. 1. Note: If the P-trap and water lines are in poor condition, replace them with new parts. Also replace any rusted or corroded fittings with new parts. The faucet can be reused and reinstalled. 4. For models with legs, place the laundry tub where it will be installed.
Installation Procedure 4. Attach the flexible water supply lines to the water shut off valves. The threaded ends of the water lines can be wrapped with Teflon pipe tape to ensure a tight, leak-proof seal. Tighten the fitting with a wrench but do not overtighten. LT-014 5. Floor Anchors WARNING A laundry tub(s) that is full of water can weigh from 175 to 350 pounds and could tip over if someone pulls against it, causing personal injuries, death, and/or damage to your home.
Care and Cleaning Warranty 6. Splash Guard Day-To-Day Cleanup As an added precaution to water splatter and/or damage to the wall behind the sink, you can install a piece of 1/8” plastic onto the wall. You can also caulk the area where the plastic meets the edge of the laundry tub. Simply wipe the surfaces with a clean towel to remove watermarks and residues.
Save these Installation Instructions for future reference. They provide important information on cleaning and maintenance of the Swan Corporation Laundry Tub. www.swanstone.
