Installation Instructions
Drop-In Kitchen Sink Installation Instructions and Templates
These Kitchen Sinks Can Also Be Undermounted. See Reverse Side For Templates of Select Models.
Tools Required:
• Ruler/Tape Measure
• Drill
• Caulk
• Masking Tape
• Safety Glasses
• Screwdriver
• Saber Saw
(if counter top cutout is required)
• 11/4” Hole Saw
KSSB-2522 25” x 22”
(635mm x 559mm)
KSDB-3322 33” x 22”
(838mm x 559mm)
KSLS-3322 33” x 22”
(838mm x 559mm)
KSLB-3322 33” x 22”
(838mm x 559mm)
KSRB-18 18
1
⁄2” DIA.
(470mm)
KSSB-3322 33” x 22”
(838mm x 559mm)
KSDB-3120 31” x 20”
(787mm x 508mm)
KSSB-2518 25” x 18”
(635mm x 475mm)
DEPTH 9” (229mm) DEPTH 10” (229mm) DEPTH 9” (229mm) DEPTH 9” (229mm)DEPTH 9” (229mm) DEPTH 9” (229mm)
DEPTH 9” (229mm)
DEPTH 7” (178mm)
DEPTH 10” (254mm)
DEPTH 10” (254mm)
DEPTH 8
1
⁄2” (216mm)
DEPTH 8” (203mm)
DEPTH 8” (203mm)
DEPTH 7” (178mm) DEPTH 7” (178mm)
A
B
C
A
B
C
D
A
B
C
A
B
C
D
A
B
A
B
A
B
C
D
A
B
C
D
INSIDE BOWL DIMENSIONS
Model A B C D
KSSB-2522 21 1/8” 17 5/8” 15 5/8” ––
(537mm) (447mm) (397mm)
KSSB-3322 29 3/4” 19” 16 1/2” ––
(756mm) (483mm) (419mm)
KSDB-3322 14 15/16” 18 7/8” 13 3/4” 15 1/4”
(379mm) (479mm) (349mm) (387mm)
KSLS-3322 18 7/8” 19 3/8” 15 5/8” 8 7/8”
(479mm) (492mm) (413mm) (225mm)
KSLB-3322 14 3/8” 18 7/8” –– ––
(365mm) (479mm)
KSDB-3120 15” 17” 13 3/4” 11”
(381mm) (432mm) (349mm) (279mm)
KSSB-2518 12” 14 3/4” 12 3/8” 8 3/4”
(304mm) (374mm) (314mm) (222mm)
KSRB-18 15 3/4” 1 3/8” –– ––
(400mm) (35mm)
Gloss Finish Models
KSGF-2522 21 1/4” 16” –– ––
(540mm) (406mm)
KSGF-3322 14” 18 1/2” 16” 14”
(356mm) (470mm) (406mm) (356mm)
Drop in side:
1. Select the drop-in kitchen sink
template that applies to the model
sink you are installing. Cut out
the inside of the template and
discard the cutout portion.
Locate the template front to rear
and right to left on the countertop
so the bowl will not interfere with
the cabinets below. Attach the
template to the countertop with
masking tape and draw a pencil
line around the inside of the tem-
plate. Discard the template.
-or-
Invert sink and position onto the
countertop . Locate sink front to
rear and right to left so the bowl
will not interfere with the cabinets
below. Trace a pencil line around
the outside edge of the sink and
remove the sink from the counter-
top. Measure in 5/16" (8mm)
from the initial sink outline and
draw a second line inside the first.
Draw a 1-1/2" radius at each cor-
ner. The second interior line will
be your cut out line.
2. Drill starter hole inside of cutout
line.
3. Using a saber saw, cut inside of
cutout line. Trial fit sink to check
proper fit.
4. Identify fixture hole locations.
Drill a starter hole from reverse
side. Working from the top side as
illustrated, position a hole saw on
the starter hole and drill to com-
plete the fixture hole. Attach
faucet, drain, and accessories
according to manufacturer’s
instructions.
5. For final fit, apply a bead of
caulk (not included) to the under-
side of the sink flange and position
sink into countertop opening. First,
tighten screws in front, then tight-
en rear screws.
6. Connect all faucet supply lines,
disposal (if available), and drain
trap fittings per manufacturer’s
instructions.
CHECK FOR LEAKS:
• Supply user tubes to faucet
• Supply riser tubes to shut off
valves or lower connections
• Fill sink with water and check
for leaks around drain
• Release water from sink and
check for possible leaks
• Tighten as needed
CUT OUT AREA
MASKING TAPE
SINK CUTOUT MEASUREMENTS
Model Width Depth
KSSB-2522 24 3/8” (619mm) 21 3/8” (543mm)
KSSB-3322 32 3/8” (822mm) 21 3/8” (543mm)
KSDB-3322 32 3/8” (822mm) 21 3/8” (543mm)
KSLS-3322 32 3/8” (822mm) 21 3/8” (543mm)
KSLB-3322 32 3/8” (822mm) 21 3/8” (543mm)
KSDB-3120 30 3/8” (771mm) 19 3/8” (492mm)
KSSB-2518 24 3/8” (619mm) 17 3/8” (441)
KSRB-18 17 7/8” (454mm) dia.
Gloss Finish Models
KSGF-2522 24 3/8” (619mm) 21 3/8” (543mm)
KSGF-3322 32 3/8” (822mm) 21 3/8” (543mm)
Measure the cutout line or the pre-cut opening to be sure it conforms to
the sizes listed.
Care and Cleaning Instructions for
Gloss Finish Models KSGF-2522 and KSGF-3322
WARNING: DO NOT USE ABRASIVES AS IT WILL DULL THE GLOSSY FINISH!
This product is made of Swanstone with a gloss finish. While it is stain resistant, it
requires regular and reasonable care. Wash regularly with warm water and a non
abrasive cleaner such as Soft Scrub Liquid Gel with bleach (without abrasives), Clorox
Clean-up with bleach, Top Job or Mr. Clean. Remove hard water stains or mineral
build up with scale removers such as Lime-Away.
DO NOT USE HARSH CLEANSERS OR ABRASIVES such as scouring powders,
abrasive cleansers or scouring pads. Abrasives will dull the finish. Protect the finish
with fiberglass wax or automotive paste wax.
Model KSGF-3322 33” x 22”
(838mm x 559mm)
Model KSGF-2522 25” x 22”
(635mm x 559mm)
Care and Cleaning
Instructions
NOTE: This procedure does not
apply to the Gloss Finish models.
Clean your Swanstone kitchen sink
with powdered abrasive cleaners.
Use of a Scotch Brite pad is
recommended to remove stubborn
stains. Occasional use of a
mild bleach and water solution
ensures that the original luster is
maintained.
A
B
D
A
B
C
Gloss Finish Models