Cabinet Mount Vanity Tops & Bowls Product Warnings Safety Guidelines Kit Contents Required Tools Preparation Tips Installation Procedure Cleaning & Maintenance Surface Repair Warranty Information Chesapeake Vanity (Single Bowl) Chesapeake Vanity (Double Bowl) Contour Vanity (Single Bowl) Ellipse Vanity (Single Bowl) Ellipse Vanity (Double Bowl) Europa Vanity (Single Bowl) ea B da ef n or d e Un In d st er al s lin ta g nd m m m m m m m m m Models: R swanstone.
Safety Guidelines The Swan Assurance — if our product is properly installed and maintained, as stated in these instructions, it will not leak. Remember – Safety First IMPORTANT NOTICE The Swan Corporation, the makers of the Swan products, cannot anticipate every possible circumstance that might involve a potential hazard during the installation of our product(s). The warnings and instructions in this installation guide are, therefore, not all-inclusive.
Safety Guidelines Personal Protection Be sure to use all personal protective equipment, such as sturdy work boots, preferably with steel toes, gloves, and hard hat, if necessary, to ensure your own safety. To prevent possible damage to your hearing, always wear ear protection, such as earmuffs or earplugs, when working around power tools. Cutting Hazard The installation of the Swanstone product may require using power tools.
General Information Sink Contents Confirm that all parts for the vanity top or bowl have been included before beginning installation.
General Information Installation Procedure Europa Vanity (Single Bowl) Unpack Carton Use care when opening the box not to damage the sink. This product is shipped to you or your retail center after careful inspection. After purchasing the sink, carefully unpack and inspect the product for any shipping damage that may have occurred. If damage is found, report it immediately to the store of purchase.
Installation Procedure Installation Procedure 1. If necessary, identify the location of additional holes for the faucet or other accessories and drill a 1/4” pilot hole from the back side of the sink. Disclaimer The information contained in this Installation Manual is given free of charge. It is based upon technical data which we believe to be reliable and is intended for use, by persons having knowledge of this technical area, at their own discretion and risk.
Installation Procedure 2. Drill fixture hole(s), using the 1/4” pilot hole for a guide, with a 1-3/8” hole saw. 2. Clean underside of vanity sink with denatured alcohol. Remove all dust and allow the surface dry completely. Dena ture Alcoh d ol VI-007 VI-008 WARNING 3. Faucet may be installed at this time per manufacturer’s instructions. Solvents Hazard Follow all manufacturers’ safety instructions for silicone sealants and denatured alcohol.
Installation Procedure 4. Place Swanstone vanity top onto the cabinet, making sure vanity is seated properly. IMPORTANT NOTICE To prevent breakage or distortion of the overflow assembly, do not use oil-based caulking or plumber’s putty near the overflow assembly. Oil-based plumber’s putty will have a harmful effect on the plastic overflow assembly, resulting in a leak. If a sealant is required between the overflow assembly and the tail pipe, use a silicone sealant. VI-006 8.
Installation Procedure WARNING 10. Connect the faucet supply lines per the manufacturer’s instructions. Dust Hazard When sanding Swanstone product, use a dust collection method which prevents dust particles from going into the air. Always work in a well-ventilated area. To keep the area well ventilated, open windows and use exhaust fans. Always use an OSHA approved dust mask when cutting, drilling, or sanding Swanstone products. 2. Trial fit side splash to vanity top checking for proper fit.
Installation Procedure 5. Caulk all seams between wall and side/back splash to create a moisture barrier. If desired, use a proper colormatched silicone sealant (not included). 5. Drill starter hole inside of cutout line. VI-030 6. Use a saber saw to cut inside of cutout line. VI-014 The installation is now complete. DO NOT discard these installation instructions. PLEASE LEAVE THEM WITH THE HOMEOWNER.
Installation Procedure Undermount Installation VI-036 Note: If undermount installation is required to be ADA compliant, refer to the wall mount installation and ADA sections. Note: Steps 1 through 3 are working from top of the countertop. 1. Position template on countertop in desired location. 2. Cut opening and finish the edge of the hole. WARNING Dust Hazard When sanding Swanstone product, use a dust collection method which prevents dust particles from going into the air.
Installation Procedure 8. Attach the sink with clips and screws. Loosely tighten the screws. 14. Connect the faucet supply lines per the manufacturer’s instructions. VI-037 VI-011 9. If mounting the bowl with an undermount overlap, bowl should be positioned, as shown. 3” Wide Plywood Strip 15. Connect the drain lines and p-trap per the manufacturer’s instructions. Approx. 1/4” 3/4” VI-010 VI-039 Note: Swanstone recommends using a licensed plumber for the installation of all necessary plumbing.
Installation Procedure ADA Installation Recommendations IMPORTANT NOTICE To prevent breakage or distortion of the overflow assembly, do not use oil-based caulking or plumber’s putty near the overflow assembly. Oil-based plumber’s putty will have a harmful effect on the plastic overflow assembly, resulting in a leak. If a sealant is required between the overflow assembly and the tail pipe, use a silicone sealant.
Installation Procedure Maintenance and Cleaning Accessibility Requirements Care and Cleaning Note: Only lavatory installations in a public space must comply with the knee and toe clearance dimensions,however we recommend these standards be used for both private and commercial installations. Also makesure that all state and local building codes are followed when installing this unit. The Swanstone products are stain and abrasion resistant; however, the finish requires reasonable care.
Warranty Warranty If a Swan product covered by this warranty is found to be defective in materials or workmanship, after inspection by an authorized Swan Corporation representative, we will repair, or at our option, exchange the product for a similar model. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation.
Swan 16 800-325-7008
800-325-7008 17 Swan
Save these Installation Instructions for future reference. They provide important information on cleaning, maintenance, and surface repair of the Swanstone Products. www.swanstone.
