Instructions / Assembly

ManualsBrandsSurebonder ManualsTools & HardwarePneumatic 23-Gauge Micro Pin Nailer

FPC Corporation - 355 Hollow Hill Drive - Wauconda, IL 60084

Phone: (847) 487- 4583 Fax: (847) 487-0174

website: www.surebonder.com e-mail: sales@surebonder.com

Read All Safety Rules and Instructions Carefully

Save this manual for Future Reference

0312

Operating Instructions

Gauge - ” Nailer

Includes: Allen wrench & oil

23 ½” 1-3/8 Pin

Model 97 10 Pin Nailer

1/2” thru 1-3/8"

Gauge

Pin Nails

Visit us at surebonder.com for our full line of products

WARRANTY

If you have any problems with this tool, please call FPC Corporation

toll-free at 1-800-860-3838 before returning it to the place of purchase.

FPC Corporation warrants this product to be free from defects in material and

workmanship, under normal conditions of use and when used in accordance with

FPC operating instructions, for a period of 90 days from the date of purchase by the

user. Within the 90 day warranty FPC at its option shall repair or replace product.

The product must be returned at the distributor/user expense, either within

warranty or out. Repaired or replaced products will receive a 60 day warranty.

USER MUST BE USING THE PROPER NAILS FOR THIS WARRANTY TO BE VALID.

WARRANTY IS VOID IF INCORRECT TYPE OF NAILS ARE USED.

Summary of content (6 pages)

PAGE 1
® WARRANTY Model 97 10 Pin Nailer If you have any problems with this tool, please call FPC Corporation toll-free at 1-800-860-3838 before returning it to the place of purchase. FPC Corporation warrants this product to be free from defects in material and workmanship, under normal conditions of use and when used in accordance with FPC operating instructions, for a period of 90 days from the date of purchase by the user. Within the 90 day warranty FPC at its option shall repair or replace product.
PAGE 2
9710 Micro Pin Nailer Part Identification 1. Exhaust valve 2. Screw 4*20 3. Washer #4*1.1t 4. Cylinder Cap 5. Gasket 6. Air Seal 7. "0" Ring 11.8*2.4 8. Spring 9. Firing Valve Piston 10. "0" Ring 21.8*2.4 11. "0" Ring 8* 3 12. "0" Ring 16* 3 13. "0" Ring 32*2.5 14. Collar 15. "0" Ring 22.4*2.65 16. Cylinder 17. Bumper 18. Body 19. Nozzle 20. Air Seal 21. Upper Remote Housing 22. Remote Core 23. "O" Ring 3.5*1.6 24. Remote Housing 25. "O" Ring 9.8* 1.9 26. Catch Guide Plate 27. Pin 2.5*22 28. Spring 29.
PAGE 3
! DANGER Troubleshooting The following form lists the common operating system with problems and solutions. Please read the form carefully and follow it. WARNING: If any of the following symptoms appear during your operation, stop using the tool immediately, or serious personal injury could result. Only a qualified person or an authorized service center can perform repairs or replacement of tool. Disconnect tool from air supply before attempting repair or adjustment.
PAGE 4
Mode of Operation IMPORTANT SAFETY WARNINGS: continued Disconnect air hose from nailer: before performing maintenance. when clearing a jam. when tool is not in use. when moving it to another location. when handing nailer to another person. DO NOT place finger on trigger when disconnecting air hose - the nailer could fire when reconnected to the air supply. Carry nailer by the handle only, not by the air hose. Do not drive nails close to the edge of the workpiece.
PAGE 5
Adjusting Air Pressure Loading Nails (continued) ! WARNING Do not exceed 120 psi. Adjust the air pressure at recommended operating pressure 70 to 120 psi according to the length of nails and the hardness of the workpiece. The correct air pressure is the lowest pressure which will do the job. Using the Nailer at a higher then required air pressure unnecessarily over stresses the Nailer. To load: Nailer has easy drop-in side loading. To open: push in track release button and slide track backward.
PAGE 6
OPERATION APPLICATIONS Including but not limited to: Finish / Trimwork, Cabinets, Molding, Furniture Making & Picture Frames Adjustable Exhaust Cover 1/4” Male Quick Release Connector Rubber Grip FEATURES - Lightweight Housing - Adjustable Exhaust - Soft Grip Handle Reduces Fatigue Track Release Button Trigger ! DANGER NEVER use oxygen or other bottled gases. Explosion may occur. This nailer is designed to operate on clean, dry, regulated compressed air, between 70 and 100 psi.