Installation Guide

ManualsBrandsSunjoy ManualsKitchenCantina 10 ft. x 13 ft. Domed Top Aluminum Gazebo

Assembly Instructions

Item#: L-GZ702PCO-A

FOR SAFE OPERATION, PLEASE READ ALL ASSEMBLY AND OPERATING INSTRUCTIONS

PRIOR TO USING GAZEBO. KEEP THESE INSTRUCTIONS FOR FUTURE USE.

Warning -

 This unit is heavy. Do not assemble this item alone.

 Read and follow all Warnings & Assembly Instructions before attempting to assemble.

 Some parts may contain sharp edges. Wear protective gloves if necessary.

 Keep all flame and heat sources away from this tent fabric.

 For safety reasons, please keep kids and pets away from the construction area of the gazebo. Children and pets

should be supervised when they are in the area of the gazebo construction.

 Begin the assembly at least 6’ (1.8 m) away from any obstruction, such as a fence, garage, house, overhanging

branches, laundry line, or electrical wires.

 Remove the canopy or take other precautions in high wind conditions.

 Install this gazebo on level ground.

 Check all bolts for tightness before use, and periodically check and tighten bolts as necessary.

Important: For technical assistance on assembly or replacement parts. Please call Sunjoy Industries at 1(866) 578-6569

from 8:30 AM to 5:30 PM EST Monday to Friday or fax the replacement part form which is in the box to

(740)-283-3549 or Email customer.care@sunjoydirect.com for assistance.

Summary of content (7 pages)

PAGE 1
Assembly Instructions Item#: L-GZ702PCO-A FOR SAFE OPERATION, PLEASE READ ALL ASSEMBLY AND OPERATING INSTRUCTIONS PRIOR TO USING GAZEBO. KEEP THESE INSTRUCTIONS FOR FUTURE USE. Warning  This unit is heavy. Do not assemble this item alone.  Read and follow all Warnings & Assembly Instructions before attempting to assemble.  Some parts may contain sharp edges. Wear protective gloves if necessary.  Keep all flame and heat sources away from this tent fabric.
PAGE 2
Parts List DESCRIPTION PART # QTY Connector 1 (Top) A1 2 Connector 2 (Top) A2 1 Bar 1 (Corner) B 4 Bar 2 (Side) C 6 D 4 Long Beam 1 E1 2 Long Beam 2 E2 2 Short Beam 1 F1 2 Short Beam 2 F2 2 Connector 4 (Beam) G 4 Support 1 (Corner) H 4 Support 2 (Post) I 8 Post J 4 Stake Cover K 4 Hook L 1 Canopy M 1 Mosquito Netting N 1 Catch O 4 Connector 3 (Corner) LINE DRAWING OF PART
PAGE 3
Hardware Packet 1 · PART # DESCRIPTION QTY AA M6 x 15mm bolt 80 BB M6 Flat Washer 96 CC M6x45 Bolt 16 DD M6 Wrench 1 LINE DRAWING
PAGE 4
Fig.1：Attach Connector 4 (G) to Long B eam (E1, E2) with Bolt (AA) and Flat Washer (BB). (same as Short beams). Fig.2: Put Stake Cover (K) under Post(J）and secure them together with Bolt (AA) and Flat Washer (BB). Fig.3: Connect Long Beam (E1, E2), Post (J) and Connector 3 (D) together with Bolt (CC) and Flat Washer (BB). Do not tighten them at this step. Fig.4: Insert Short Beam (F1, F2) into the gap between Post (J) and Connector 4 (D) and secure them with Bolt (CC) and Washer (BB).
PAGE 5
Hardware Packet 2 PART # DESCRIPTION QTY AA M6 x 15mm bolt 16 BB M6 Flat Washer 20 JJ Hook (Mosquito Netting) 56 XX M6 x 15mm bolt 4 LINE DRAWING Fig.7: Attach Connector 2 (A2) to Connector 1 (A1) with Bolt(AA）and Flat Washer (BB), and then screw Hook (L) into Connector 2 (A2). Fig.8: Insert Bar 1 (B) into Connector (1) (A1). Fig.9: Insert the other end of Bar 1 (B) into Connector 4 (D). XX Fig.10: Insert Bar 2 (C) into Connector 1 (A1). Fig.
PAGE 6
Hardware Packet 3 PART # DESCRIPTION QTY GG Stake 6 x 180 12 LINE DRAWING Fig.13: Secure the Stake Cover (K) on the ground with Stakes (GG). Fig.14: Hang Mosquito Netting (N) on Hook (JJ). Fig.15: Place Larger Canopy (M) on the top (the assembled bars) and spread it out, then use the caps on the middle to attach.
PAGE 7
Limited Warranty: This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of your item provided the item is maintained with care and used only for personal, residential purposes. The item is warranted to be free from defects in material or workmanship for a period of one (1) year. We don't reimburse for transportation or delivery costs, or compensate the individual or any outside party for assembling or disassembling the product.