Replacement Part List

ManualsBrandsSun Joe ManualsChainsaws8 in. 6.5 Amp Electric Multi-Angle Telescopic Pole Saw Refurbished in Gray

, LLC

A Division of Snow Joe

, LLC

Model SWJ802E/

SWJ802E-GRY/SWJ802E-PRP

Form No. SJ-SWJ802E/

SWJ802E-GRY/SWJ802E-PRP-880E-M

OPERATOR’S MANUAL

SAVE THESE INSTRUCTIONS

8-INCH 6.5-AMP ELECTRIC

POLE CHAIN SAW

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Always follow these safety guidelines. Failure to do so may

result in serious bodily injury or death.

mDANGER! This indicates a hazardous situation, which,

if not followed, will result in serious injury or death.

mWARNING! This indicates a hazardous situation, which,

if not avoided, could result in serious injury or death.

mCAUTION! This indicates a hazardous situation, which,

if not avoided, could result in minor or moderate injury.

General Safety

mWARNING! When using electric yard tools, basic safety

precautions should always be followed to reduce the risk of

re, electric shock, and personal injury, including the following:

1. Keep guards in place – Protective guards should be

checked periodically to ensure they are properly tted and

in correct working order.

2. Remove adjusting keys and wrenches – Check that

adjusting wrenches are removed from the saw before

turning it on.

3. Keep work area clean and well-lit – Clear work area of

branches and limbs after each cutting session. Cluttered

areas invite accidents.

4. Do not use in dangerous environments – Do not use

power tools in damp or wet locations.

5. Do not use the pole chain saw in the rain.

6. Keep bystanders and children away – All bystanders,

including children and pets, should be kept a safe

distance away from the work area.

7. Do not force the tool – It will do the job eectively and

safely if it is used at the rate for which it was designed.

8. Use the right tool – Do not force the tool or any

attachment on the tool to do a job for which they were

not designed.

9. Wear proper apparel – Do not wear loose articles of

clothing or jewelry since such items may get caught

in moving parts. Use of heavy-duty rubber gloves,

substantial non-skid footware, and close-tting clothing is

recommended when working outdoors with power tools.

10. Wear protective hair coverings to contain long hair.

11. Always wear safety glasses and ear defenders to

provide eye and ear protection – Everyday eyeglasses

only have impact resistant lenses and do not provide the

same protection as safety glasses.

12. Wear face or dust masks – If the cutting operation is

dusty, the use of a face or dust mask specially designed

to lter out miscoscopic particles is recommended.

13. Do not overreach – Keep proper footing and balance

at all times.

14. Maintain tools with care – Keep tools sharp and clean

for best and safest performance. Follow instructions for

lubricating and changing accessories.

15. Disconnect tool – Disconnect the pole chain saw from

the power supply when not in use, before servicing,

when transporting, or when changing the chain or other

accessories.

16. Reduce the risk of unintentional starting – Make sure

the switch is in the OFF position before plugging the tool

into a power source.

17. Use recommended accessories – Consult the owner’s

manual for recommended accessories. The use of

improper accessories may cause risk of injury.

18. Check for damaged parts – Before each use, repair or

replace any guard or part that is damaged. In addition,

check for alignment of moving parts, binding of moving

parts, breakage of parts, and any other conditions that

may aect the tool's operation.

19. Never leave tool unattended while it is running – Turn

the power OFF by removing the power cord directly from

its socket. Do not leave the saw until the cutting bar

comes to a complete stop.

20. Avoid unintentional starting – Do not carry the pole

chain saw with your nger on the switch.

21. Do not grasp the exposed cutting blade or cutting

edges when picking up or holding the saw – Be sure to

encase the cutting bar in its protective sheath when not

in use.

22. Stay alert – Watch what you are doing. Use common

sense. Do not operate the pole chain saw when you are

tired.

23. Store idle tool indoors – When not in use, appliances

should be stored indoors in a dry and high or locked-up

place out of the reach of children.

Summary of content (20 pages)

PAGE 1
8-INCH 6.5-AMP ELECTRIC POLE CHAIN SAW Model SWJ802E/ SWJ802E-GRY/SWJ802E-PRP Form No. SJ-SWJ802E/ SWJ802E-GRY/SWJ802E-PRP-880E-M OPERATOR’S MANUAL A Division of Snow Joe®, LLC IMPORTANT! substantial non-skid footware, and close-fitting clothing is recommended when working outdoors with power tools. Safety Instructions 10. Wear protective hair coverings to contain long hair. All Operators Must Read These Instructions Before Use 11.
PAGE 2
mWARNING! Some dust and debris created by the m use of the tool could contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: WARNING! m Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings: • Chemicals in fertilizers • Compounds in insecticides, herbicides, and pesticides • Do not allow any part of the pole chain saw to make contact with water while it is in operation.
PAGE 3
Specific Safety Rules For Pole Chain Saws AVOID CONTACTING THE GUIDE BAR TIP WITH ANY OBJECT. In some cases, when the tip makes contact with an object, it may cause a fast reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may also push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the pole chain saw, which could result in serious personal injury.
PAGE 4
Safety Symbols The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbols Descriptions Symbols READ THE OPERATOR'S MANUAL(S) – Read, understand and follow all instructions in the user manual(s) before attempting to assemble and operate. Descriptions Keep bystanders and children a safe distance away. WARNING! Do not expose the unit to rain or wet conditions.
PAGE 5
Know Your Electric Pole Chain Saw Read the owner’s manual and safety instructions carefully before operating the pole chain saw. Compare the illustration below to the pole chain saw in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. This picture is from the opposite side of this illustration 6 3 4 5 MIN 8 7 2 11 1 12 13 9 10 14 16 15 This picture is from the opposite side of this illustration 17 18 19 1. 8 in.
PAGE 6
Unpacking Installing/Replacing the Guide Bar and Chain Carton Contents Tools and supplies required: • Electric pole chain saw • Dual-tipped hex key wrench/blade screwdriver (supplied) • 8 in. (20.3 cm) Oregon chain • Heavy-duty work gloves • 8 in. (20.3 cm) Oregon guide bar NOTE: When replacing the guide bar and chain, use only identical replacement parts. Make sure the pole chain saw is disconnected from the power supply before proceeding with installation.
PAGE 7
6. Starting at the tip, mount the chain drive links into the bar groove, leaving a loop at the back of the bar. The chain will loosely fit until it is placed on the sprocket. (Figs. 7 & 8) Fig. 4 NOTE: Make certain of the direction of the chain . If the chain is mounted backwards, the saw will vibrate abnormally and will not cut. Fig. 7 Chain/sprocket end cover 3. Remove the cutting bar and chain from the mounting surface (Fig. 5). Fig. 5 Fig. 8 Chain Cutting bar 4. Remove the old chain from the bar.
PAGE 8
9. Adjust the chain tension as needed by adjusting the chain tensioner screw with the supplied flat-tip blade screwdriver. Make sure to align the chain tensioner screw with the pin hole (Fig. 10). Fig. 12 Fig. 10 Chain tensioner Chain tensioner screw 12. Tighten the end cover nut using the hex key wrench (Fig. 11), then replace the end cover nut cap to secure the chain/sprocket end cover (Fig. 13). Blade screwdriver 10.
PAGE 9
Fig. 14 Oil level window mWARNING! Failure to lubricate the chain will cause Oil tank cap damage to the bar and chain. Use only a good quality bar and chain oil designed specifically for use with chain saws. One minute of use will consume approximately 0.15 fl oz. (5 ml) of oil. NOTE: It is normal for oil to seep from the saw when not in use. To prevent seepage, empty the oil tank after each use.
PAGE 10
4. To turn the tool ON, push and hold the safety lock button (located on the rear handle) with your thumb and then squeeze the trigger with your fingers. Once the tool is running, you can release the safety lock button (Fig. 16). 4. Lock the pole in position by closing the cam-lock (Fig. 19), and ensure that the pole is secure. If the pole telescopes when the cam-lock is closed, the nut may need tightening. Fig. 19 Fig.
PAGE 11
• The most typical cutting application is to position the unit at an angle of 60° or less depending on the specific situation (Fig. 24). As the angle of the pole chain saw shaft to the ground increases, the difficulty of making the first cut (from the underside of limb) increases. Fig. 21 Fig. 24 Multi-angle head adjustment dial 3. Adjust the head to the desired position (Fig. 22). Fig. 22 60º MAXIMUM Basic Cutting Procedure This unit is designed for trimming small branches and limbs up to 7.5 in.
PAGE 12
Either of these reactions can cause loss of saw control, which can result in serious injury. Do not rely exclusively upon the safety devices built into the saw. As a pole chain saw user, you should take several steps to keep your cutting jobs free from accident or injury. Load Second Cut Take the following precautions to minimize kickback: • Before you start the unit, make sure the pole chain saw is not contacting any object.
PAGE 13
mWARNING! Always unplug the power cord before performing any adjustments, maintenance, or repairs to your pole chain saw. • Use protective gloves when handling the bar and chain. • Keep the bar encased in its sheath, except when working directly on the bar or the chain. • Never dispose of oils or other polluting materials in unauthorized places. Motor Cooling To avoid overheating and damage to the motor, always keep the cooling air vents clean and free of sawdust and debris.
PAGE 14
Fig. 27 Fig. 28 Inspection tool < 0.5 mm Troubleshooting Depth limiter tooth Troubleshooting Tips Most difficulties are easy to fix. Consult the troubleshooting table for common problems and their solutions. If you continue to experience problems or need repairs beyond these minor adjustments, please call 1-866-SNOWJOE (1-866-766-9563) for assistance.
PAGE 15
Chain Maintenance Table Chain Pitch Limiter Tooth Level (a) File Diameter (d) a d inches mm inches mm inches mm 3/8 Mini 9.32 0.018 0.45 5/32 4.0 0.325 8.25 0.026 0.65 3/16 4.8 3/8 9.35 0.026 0.65 13/64 5.2 0.404 10.26 0.031 0.80 7/32 5.6 mCAUTION! Daily Checklist, Cleaning and Storage • Remove the power cord and wait at least five minutes for the saw to cool before servicing or storing your unit. • If you drop the saw, carefully inspect it for damage.
PAGE 16
Support If your Sun Joe® Saw Joe SWJ802E/SWJ802E-GRY/ SWJ802E-PRP electric pole chain saw requires service or maintenance, please call 1-866-SNOWJOE (1-866-766-9563) for assistance. Model and Serial Numbers When contacting the company, reordering parts, or arranging service from an authorized dealer, you will need to provide the model and serial numbers, which can be found on the decal located on the housing of the unit. Copy these numbers into the space provided below.
PAGE 17
Accessories mWARNING! ALWAYS use only authorized Snow Joe + Sun Joe® replacement parts and accessories. NEVER use replacement parts or accessories that are not intended for use with this saw. Contact Snow Joe® + Sun Joe® if you are unsure whether it is safe to use a particular replacement part or accessory with your saw. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
PAGE 18
NOTES 18
PAGE 19
SNOW JOE® + SUN JOE® CUSTOMER PROMISE ABOVE ALL ELSE, Snow Joe® + Sun Joe® are dedicated to you, our customer. We strive to make your experience as pleasant as possible. Unfortunately, there are times when a product does not work or breaks under normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we created the Snow Joe® + Sun Joe® promise. OUR PROMISE: Snow Joe® + Sun Joe® warrant new products for two years from the date of purchase.
PAGE 20
snowjoe.