BEVERAGE MERCHANDISERS Models: ALBV15 SCR1400W SCR1401 SDBV2445 LABV2430 AL57G SCR1400WLH SCR1401LH SDG1526 ADBV2441 SCR1536BG SCR610BL ASDG1521 LBV1546 SDG2415 SCR2464 SCR611GLOS LABV15442 SDBV1555 LBV2434 SCR610BLSD SCR1156 ADBV1551 ASDG2411 User Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Write Serial Nos. (on lower left corner of inside cabinet) here: Felix Storch, Inc. An ISO 9001:2015 registered company 770 Garrison Ave Bronx, New York 10474 www.
TABLE OF CONTENTS Appliance Safety 3 Important Safeguards 3-4 Location of Parts 5-9 Installation Instructions 10-15 Before Using your Appliance 10 Installation of your Appliance 10-11 Electrical Connection 12 Reversing the Door Swing of your Appliance 12-14 Adjusting the Kick Plate 14 Installing the Stainless Steel Handle 14-15 Operating your Appliance 15-20 Control Panel 15-16 Settings Mode 16-17 Interior Light 17 Control Panel only for models SCR610BL, SCR610BLSD and SCR1156 17-18 Dynamic Cooling Mode 18
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the words "DANGER" or "WARNING".
- The more coolant there is in an appliance, the larger the room it should be installed in. In the event of a leakage, if the appliance is in a small room, there is the danger of combustible gases building up. For every ounce of coolant at least 325 cubic feet of room, space is required. The amount of coolant in the appliance is stated on the data plate inside the appliance. It is hazardous for anyone other than an Authorized Service Person to carry out servicing or repairs to this appliance.
LOCATION OF PARTS Models ALBV15 / SCR1536BG Digital Control Panel Door Shelves (3) Handle Security Lock Kick-Plate Adjustable Legs Cabinet Model SCR2464 Digital Control Panel Door Shelves (3) Handle Security Lock Kick-Plate Adjustable Legs Cabinet 5
Model AL57G Digital Control Panel LED Light Handle Shelves (3) Door Security Lock Kick-Plate Adjustable Legs Models SCR1400W / SCR1400WLH* Digital Control Panel Door Shelves (6) Handle Security Lock Kick-Plate Adjustable Legs Cabinet * NOTE: Model SCR1400WLH opens from the right, so the handle is on that side.
Model SCR611GLOS Digital Control Panel Door Shelves (3) Handle Security Lock Kick-Plate Adjustable Legs Model SCR610BL / SCR610BLSD* Door Shelves (3) Handle Security Lock Kick-Plate Adjustable Legs Digital control panel Cabinet * NOTE: Model SCR610BLSD has a solid door.
Model SCR1156 Door Shelves (4) Handle Security Lock Kick-Plate Adjustable Legs Digital control panel Cabinet Models SCR1401 / SCR1401LH* Digital Control Panel Door Shelves (6) Handle Security Lock Kick-Plate Adjustable Legs Cabinet 8
* NOTE: Model SCR1401LH opens from the right, so the handle is on that side.
INSTALLATION INSTRUCTIONS Before Using your Appliance • Remove the exterior and interior packing. CAUTION: After unpacking you MUST allow this appliance to stand upright for at least 2 hours to allow the lubricant and refrigerant to drain back into the compressor and stabilize. Failure to do so may adversely affect performance and the lifetime of this unit. • • Clean the interior surface with lukewarm water using a soft cloth. Install the handle on the door. (See Installing the Stainless Steel Handle.
Built-in Under-counter Instructions Make sure your installation does not block the front ventilation grille. The unit is designed to fit under worktops, using the height-adjustable ventilation grille to ensure that the feet are concealed from the front view. If the unit is to be installed in an area with a kitchen plink, make sure that the ventilation gaps in the plinth are at least 300cm2 (46.5in2) and remove the ventilation grilles, so that warm air can disperse without interruption.
Electrical Connection This appliance should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug that fits with standard three-prong wall outlets to minimize the possibility of electrical shock. Do not under any circumstances cut or remove the third (grounding) prong from the power cord supplied. For personal safety, this appliance must be properly grounded. This appliance requires a standard 115/120 Volt AC ~60Hz three-prong grounded electrical outlet.
Models ALBV15 / SCR1536BG / SCR2464 / SCR610BL / SCR610BLSD / SCR611GLOS 1. Remove the bottom hinge (2) by unscrewing the four lock screws (1). Hold the door firmly after removing the screws. (Fig. 1) 2. Gently pull down to remove the door from the right top hinge and place it on a padded surface to avoid the risk of damage. Then remove the right top hinge (4). (Figs. 3 & 4) 3. Unscrew and transfer pins (3) and (7) of the hinge plate to the opposite side. (Fig. 2) 4.
Adjusting the Kick Plate Only for Models ALBV15 / AL57G / ASDG1521 / LABV15442 / ADBV1551 / SDG1526 / LBV1546 / SDBV1555 / ASDG2411 / LABV2430 / ADBV2441 / SDG2415 / LBV2434 / SDBV2445. The pre-fitted kick-plate of the appliance includes an adjustable kick-plate section that is initially seated behind the upper section. To adjust the kick-plate height, follow the instructions below: 1. Remove the screws (1) from both the top left- and top right-hand sides of the kick-plate. 2.
For the SCR610BLSD model: 1. Use a screwdriver to remove the screws on the side of the door where the handle is to be installed. 2. Align the handle (2) with the screws (1) removed as above. 3. Tighten the screws using a Phillips head screwdriver until the handle is both flush and secured tightly against the door side (3). NOTE: (DO NOT over-tighten as this will cause damage to the stainless steel door surface.
Light Indicator / Multi-key Function The interior light indicator is the dot at the bottom right of the display. The interior light indicator will light up in showcase mode. The interior light indicator will flash when the multi-key function is selected. To perform the multi-key function, lightly touch and hold the first key, then touch the rest key for at least 5 seconds, and then release all the keys. Setting the Temperature Control • You can set the temperature by touching the UP and DOWN symbols.
Fan Mode ▪ Lightly touch and hold the UP key for 5 seconds and then touch the POWER key three times. ▪ Use the UP and DOWN keys to select the fan mode. The factory default setting is F0 or F2. F0: Silent mode - Energy saving mode F1: Dynamic Cooling mode - half time F2: Dynamic Cooling mode - full time ▪ Touch the POWER key to confirm your selection. ▪ Touch and hold the UP key for 5 seconds to leave settings mode. Otherwise, the appliance exits settings mode automatically after approximately one minute.
NOTE: Pressing the POWER key once can switch off the audible alarm when the alarm is on. Up Used to increase (warm) the set temperature by 1°C/1ºF. To switch on the Silent mode, press and hold the UP key for 5 seconds. Three beeps will confirm the selection. Down Used to decrease (cool) the set temperature by 1°C/1ºF. To switch on the Dynamic Cooling mode, press and hold the DOWN key for about 5 seconds. Five beeps will confirm the selection. Light The interior light makes it easy to view your items.
You can tell whether your unit is in Dynamic Cooling or Silent mode by the sound of the internal fan motor. When the compressor is OFF if the internal fan motor is working, the unit is in Dynamic Cooling mode, but if the internal fan motor is also OFF, the unit is working in Silent mode. Sabbath Mode • • • Sabbath mode is available for the observance of certain religious holidays. This mode turns off the displays, interior light, and audible alarms and prevents them from turning on again.
Defrosting • • • The unit defrosts automatically in normal operating conditions. The evaporator behind the rear wall of the unit defrosts automatically. The condensate collects in the drainage channel behind the rear wall of the unit and flows through the drainage hole into the drip tray near the compressor where it evaporates. However, frost may accumulate on the evaporator if the unit is repeatedly opened in high heat or high humidity location.
TROUBLESHOOTING You can solve many common problems easily, saving you the cost of a service call. Try the suggestions below to see if you can solve the problem before calling the servicer. PROBLEM Appliance does not operate. POSSIBLE CAUSE Appliance is not connected to a power supply. The appliance is turned off. A tripped circuit breaker or a blown fuse. The temperature is not set correctly. The ambient temperature could require a lower set temperature setting. The door was opened too often.
“E7”. The alarm sounds and the temperature display flashes. The icon “--” is lit up and flashing in the temperature display. “E3” or “E4” indicates that the defrost sensor in the evaporator has failed. “E5” indicates a defrost heater failure. “E6” indicates a solenoid valve failure. “E7” indicates a door switch failure. Has the appliance door been open for longer than 60 seconds? If not, then the temperature has risen higher or fallen lower than the set temperature.
NOTES 23
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, the warrantor will pay for factory specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
