O U T D O O R OV E N M A N UA L
The Oven Manual Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1(800) 966 -8126 , Monday - Friday, 8 :30 a.m. - 5 p.m., P ST. FOR QUESTIONS OR SERVICE, PLEASE CALL 800.966.8126 Oven Operation 1 -2-3 Before Cooking : Step 1 Keep yourovena safe distance away from your property.* Step 2 Always perform aleak test.* Step 3 Keep children away from the oven.
Step 1 Step 2 Step 3 The Oven Manual Burn ovenfor 10-15 minutes to burn off food residue. Wait until theovenis completely cooled before closing oven door . Clean up grease build -up and cover your oven. * Please refer to the owner's manual for deta ils. WARNING DANGER If you smell gas: 1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance. 2.
TABLE OF CONTENTS Safety Information………………… ………………….………...….………….………….………… ……. 4 Package Contents…..………………..…..….……...…. Hardware Contents… ..................……………………………… ……. 6 …………………………………………………………….……………………….. 7 Assembly Instructions………… …………..……………….……………………………………… ……. 8 LP Gas Assembly……… ……………………………………………............... .............................. ..... 15 Natural Gas Conversion …………………………………………………………………………… …... 21 Operating Instruction s.. ………………………….……...… …………………………..................
Safety Information Please read and understand this entire manual before attempting to assemble, operate install the product. If you have any questions regarding the product, please call service at 1(800) 966 -8126 Monday t o Friday from 8 :30 a.m. to 5 p.m. PST. or customer 1. The installation of this appliance must conform with local codes or, in the absence of codes, local Propane with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Installation Code, CSA/CGA -B149.1. 2.
Safety Information This regulator is set for an outlet pressure of 11.0 WC. 16. The cylinder used must include a collar to protect the cylinder valve 17. Do not store a spare LP-gas cylinder under or near the appliance 18. Never fill the cylinder beyond 80 percent full 19. If the information in “17” and “18” is not followed actly, a exfire causing death or serious injury may occur. 20.
PACKAGE CONTENTS PART A B C D DESCRIPTION Main Body CookingGrill Pizza S tone Bottom Grill PART E F G QUANTITY 1 2 1 1 7 DESCRIPTION Grease Tray Smoker Box Flame Tamer QUANTITY 1 1 1
HARDWARE CONTENTS The following list is included inside the oven carton: Battery 1 pc The following list is not included inside the pizza oven carton, but needed when the user is assembling the pizza oven. Phillips HeadS crewdriver 1 pc The following list is NOT included inside the pizza oven carton but is included inside the NG Conversion Kit. It is needed when the gas type is changed from LP to NG. 11X11 mm Wrench1 pc Orifice R emoval T ool 1 pc φ 1.
ASSEMBLY INSTRUCTIONS Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt toassemble the product. Assembly tip! (Please lightly tighten the screws during assembly of the cart. When the cart is completed THEN TIGHTEN ALL THE screws. This will make it easier to make all the holes align properly) 1. Use screw M6*40 × 2 pcs, nut M6× 2 pcs and flat washer 18*6.
3. Use screw M6*12 ×2 pcs to fix the left side panel onto the base panel of the stand.(Note: The panel should have the “small holes at the top” to the front of the cart assembly) 4. Use screw M3*12 ×2 pcs and nut M3×2 pcs to attach the door magnet onto the right side panel. (Note: Please attach the magnet BEFORE you put the right side panel on. Check to verify that the magnet points to the FRONT of the cart. This holds the door closed) 5.
6. Use screw M4*10 ×4 pcs and nut M4×4 pcs to attach the transformer assembly onto the outside of the back panel of the stand.(Note: These screws can be tightened at this time) 7. Use screw M6*12 ×5 pcs to attach the stand base panel onto the base panel, between the two side panels.
8. Use screw M4*10 ×4 pcs to fix the standdoorhorizontalbeam between the two side panels. (N ote: Please fasten the upper two screws first, and then the lower two screws. ) 9. Use screw M4*10 ×4 pcs to fix the stand top panel on the top of the two side panels and back panel. (Note: These screws can be tightened at this time) 10. Use screw M5*10×8 pcs to attach triangle×2 pcs on the bottom of the base panel, leaning against the two side panels.
11. First, insert the door lower axis into the hole in the base panel. Next, push down the door upper spring axis and let goof the spring when it is pointed to the hole in the horizontal beam.(Note: You may need to add 1 or 2 washers 18*6.4*1 on the bottom pin so the door will close evenly) ALMOST FINISHED!! 12. Put the oven assembly on the stand-top panel. Use screw M6*12 ×4 pcs to fasten the oven onto the stand.
13. Use screw M5*10 ×16 pcs to attachside shelf bracket ×4 pcs onto the drawer side panels. (Note: Arrows face UP) 14. Using one ofthe screw M5*10 to fix the match holder onto the front bracket of right side shelf. (This step may be skipped if you do not want or need a “match holder” on your unit) 15. Use screw M6*12 ×8 pcs and special nut TB31 -05-03×8 pcs to hang side shelf×2 pcs onto the four brackets.
16. Use screw M4*8 ×3 pcs to fix the chimneyassembly onto the top of the oven exterior. (Note: These screws can be tightened at this time) 17. Use screw M5*35 ×4 pcs to fix the back heat shield onto the back panel of the oven. The order is: screw back heat shield heat insulationwasher flat washer oven back panel. 18.
19. Insert the grease trayinto the back of theoven. 20. Insert the battery into the electronic ignition. Unscrew the button and place battery positive (+) tip facing OUT. Screwbutton back on. Your complete oven is now assembled. L.P. GAS INSTALLATION Gas grills that are set to operate with L.P. gas come with a high capacity hose and regulator assembly.
5. Make sure all burner knobs are in the OFF position. 6. Connect thehose and regulator assembly to the tank val ve (See Fig. 6). Hand-tighten the quick coupling nut clockwise to a full stop. Fig. 6 DO NOT use a wrench to tighten because it could damage the quick coupling nut and result in a hazardouscondition. 7. Open the tank valve fully (counterclockwise). Use a soapy water solution to check all connections forleaks before attempting to light your rill.gSee “Pre -Operation Leak Testing" on page19.
WARNING: The Type I connective coupling (see Fig. 7) supplied w ith your oven must not be replaced with a different type of grill/tank connection system. Removal will result in loss of warranty, gas leakage, fire and severe bodily harm. Hand Wheel External Thread Thermally Sensitive Nut Propane Regulator Type I Valve PIG 7 Disconnecting a Liquid Propane G as (LP Gas) Tank from Your Oven : 1. Turn the burner knobs and LP gastank valve to the full OFF position. (Turn clockwise to close.) 2.
L.P. TANK INFORMATION Never use a dented or rusted L.P. tank or cylinder with a damaged valve. L.P. cylinders are equipped with an O.P.D. (Overfilling Prevention Device). The device shuts off the flow of gas to a cylinder after 80% capacity is reached. This limits the potential for release ofgas when the cylinder is heated, averting a fire or possible injury. The L.P. cylinder must have ashut-off valve terminating in an L.P. gas supply cylinder outletspecified, as applicable, for connection No.
PRE -OPERATION LEAK TESTING Although all gas connections on the ovenare leaktested prior to shipment, a complete gas tightness check must be performed at the installation site due to possible shifting during shipment, installation or excessive pressure unknowingly being applied to the unit. Periodicallycheck the whole system for leaks and immediately check the system if the smell of gas is detected. 1. Do not smoke while leak testing. 2. Extinguish all open flames. 3. Never leak test with an open flame. 4.
WARNING Do not use the ovenin garages, breezeways, sheds or any enclosed area. Never operate the oven in enclosed areas as this could lead to a carbon monoxide buildup, which could result ininjury or death. Place the oven on a level surface. Avoid moving the ovenwhile it is in operation. NOTE: The oven will operate best if it is not facing directly into the wind PREPARATION FOR NG CONVERSION: Before beginning conversion, make sure all parts are present. Compare parts with package contents.
WARNING : Place the ovenon a flat, level surface. Before the conversion, make sure all control knobs are in the OFF position, LP tank valve is closed, and tank is disconnected from regulator and removed from grill. NG CONVERSION INSTRUCTION: Before theconversion, make sure all control knobs are in the OFF position, LP tank valve is closed, and tank is disconnected from regulator and removed from oven .
Use a screwdriver to loosen the screw that is used to fasten the burner cover. Turn the burner cover until the hole marked “ NG” overlaps with the fixing hole on the burner.Put the screw back into the holes and tigh ten again. Use orifice removaltool to remove theφ 1.2 L P orifice from the oven. And then use the same tool to fix theφ 1.8 NG orifice back to the position.
Put the burner back into the oven and insert the ignition wire into the original po sition. Use the 10x12 mm spanner to fix the thermocouple back into the oven again. Finally, fasten the burner with the original screws. Put back the two cooking grids , smoker box, pizza stone and base grill into the right position. Use the 17X19 mm wrenchto remove the regulator and then put on the NG hose. Fasten the hose using 17X19 mm wrench.
Use the screw driver to put the conversions crewinto the knob. When converting to natural gas, please be aware that the low heat settingof the mainburners and searing burneris “NG LOW ,”as shown on the control panel. “LP LOW” setting is not applied when converting to natural gas. WARNING: Please remem ber this is an outdoor gas oven . Many areas of the grill generate extreme heat. We have taken every precaution to protect you from the contact areas.
IMPORTANT: After your outdoor ovenis converted to natural gas, the working pressure for natural gas is 7-inche water column (WC). Gas pressure is affected by gas line size and the length of gas line run from house. Follow the recommendations in the chart below. Distance Up to 25 ft. 26 – 50 ft. 51 – 100 ft. Over 101 ft. Burner Main Burner From Ho use to Oven Tubing Size 3/8 in. DIA 1/2 in. DIA 2/3 in. of run3/4 in. 1/3 in. of run1/2 in. 3/4 in.
Never attach an unregulated gas line to the appliance. Connection to an gas line can cause excessive heat or fire. unregulated Verify the type of gas supply to be used, either Natural Gas (N.G.) or Liquid Propane (L.P.), andmake sure the serial plate agrees with that of the supply. Conversion kits are available separately fo r an additional cost , which willenable you to convert your oven from L.P. to N.G. or to convert your oven from N.G. to L.P. Please see your local dealer for more information.
. Clearance to combustible construction: A minimum 61 of cm (24 inches) from thesides and back must bemaintained from the gas grill above and below the cooking surface to adjacent vertical combustible construction. Clearance to non -combustible construction: A minimum of61 cm (24 inches) clearance from the back of thegrill to non-combustible construction is required. Storage of anoutdoor gas cooking appliance indoor is permissible only if the cylinder is disconnected and removed from the appliance.
WARNING Heat and smoke exhaust out of the chimney and the ventilation holes on the bottom of two oven sidepanels(See Fig. 8). Make sureto keepanythingthatcould bedamaged by heat or smoke away from the heat and smoke exhaust holes. GENERAL RULES Do not leave the oven unattended while cooking! 1. Make sure theovenhas been leak -tested and is properly located. 2. Light the grill burners using the instructions provided in this manual. 3.
Operating Instructions OVEN BURNER LIGHTING Warning: Do notlean over oven when lighting. Turn off LP supply at cylinder when appliance is not in use. Main Burner Lighting Illustration: 1. Check that the control knobs are in the OFF position. 2. Open valve at tank fully by turning counterclockwise. 3. The door must always be in the OPEN position for lighting; 4. Push the Electronic Ignition down 3 to 4 seconds while turning the control knob to the HIGH position. The burner should ignite.
USING THE GRILL LIGHT Light Operation Instruction 1. Make sure the light’s power switch on the control panel is in the “OFF” position. 2. Connect power plug properly to grounded outlet. 3. Turn the light’s power switch to “ON.” WARNING Keep any electrical supply cord away from any heated surface. IMPAIRED V ENTILATION OF HOT AIR FROM OVEN - In order for the burners to function properly, hot air created by the burners must have a way to escape.
Care & Maintenance GENERAL MAINTENANCE - Keep outdoor cooking gas appliance area clear and free from combustible materials, gasolineand other flammable vapors and liquids. - Do not obstruct the flow of combustion and ventilation air. - Keep the ventilation openings of the cylinder enclosure free and clear from debris. - Visually check the burners. GENERAL CLEANING IMPORTANT: Before cleaning, make sure al l controls are off and the oven is cool. Always followlabel instructions on cleaning products.
The drip trayshould be cleaned periodically according to the using situation . NOTE: Allow the drip tray to cool before attempting to clean. COOKING GRATES The cooking grates can be cleaned immediately after cooking is completed and after turning off the oven. Wear a barbecue mitt and scrub the cooking grates with a damp cloth. the oven If is allowed to cool down, cleaning the grates will easier be if removed from the oven and cleanedwith a mild detergent.
Definitions: (+) Guard– Guard is a portion of portable luminaries unit that prevents inadvertent contact with the bulb. It may be integrated with the UV filter or lamp containment barrier or as part of an enclosure or shade. (+) Lamp containment barrier – lamp containment barrier is a portion of a portable luminaries unit that encloses the bulb. (+) UV filter – UV filter is a portion of a portable luminaries unit that limits ultraviolet (UV) emissions. 1.
3. Use screw driver to loosen the screw that fix the light assy. 4. Use one hand to hold the metal backpart of the light and one handleto hold the front glass cover and then take them apart. Then you canreplacethe bulb. 5. After replacement, use one hand to hold the metalbackpart of the light and one handleto hold the front glass cover and then clip them together in the right position.
6. Use M4*10 screw to fix the light assy. on to the back panel of the oven. 7. Use screw M5*35× 4 pcs to fix the back heat shield onto the back panel of the oven. The order is: screw back heat shield heat insulation washer flat washer oven back panel.
8. Finally, put back the two cooking grills, smoker box, pizza stone, base grill and flame tamer into the oven. Now you have finished replacing the bulb. Cleaning Method Follow Steps belowfor glass cover removal. Use a damp towel to clean the surface glass of cover. Make sure the glass cover is completely dry before reinstalling. WARNING Make sure the light switch is on “OFF” position and power plug is power outlet prior to cleaning the glass cover.
Replacing Battery for Electrical Igniter: 1. Remove the igniter cap by turning clockwise; 2. Replace the battery; 3. When installing new battery, ensure it is installed with the proper polarity; 4. Put on the igniter cap back by turning counterclockwise. WARNING: 1. To protect against electric shock, do not immerse cord or plugs in water or other liquid. 2. Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts. 3.
2. Loosen theM4*10 screw * 7 pcs that fix the door exterior and interior, and then loosen the M4*10 screw * 4 pcs that fix the door hinge. Thenloosen the shoulderscrew thatattachesthe door handle. 3. Use spanner 19# to loosen the nut that fix the temp eraturegauge. And then you can completely separate the oven door exterior and interior so as to do the cleaning. 4. After cleaning, you need to re-assemble the oven door.
5. Use spanner or handdirectlyto tighten the nut that fix the temperaturegauge on the glass. You can set the torque of the spanner at4.0kgf*cm. 6. Use M4*10 screw * 4 pcs to fix the door onto the oven. Now you have finished cleaning the oven door.
TROUBLESHOOTING Many solutions given here can make your grilling experience safer and more enjoyable. You can also call the customer service department at 1-866 -410 -0408 , 8 a.m. – 5 p.m., P ST, Monday to Friday. PROBLEM Grill will not light. Burner flameis yellow andgas odorcanbe smelled. Excessive flare-up. Burner blows out. Low heatwith the knobin “HIGH” position. POSSIBLE CAUSE CORRECTIVE ACTION 1. The ignition wire came off the 1. Reconnect the ignition wire to the electrical igniter/valve.
TROUBLESHOOTING Low heat,LP gas. Low heat, natural gas. Cooking light will not turnon. Burner Orifice Size Main Burner Φ 1.8 mm 2. Clear ports of any obstructions. 3. Refill the LP tank. The propane regulator assembly Please follow these instructions: incorporates an excess flow device 1. Make sure all burners are “OFF .” designed to supply the grill with 2. Open the tank valve and wait 5 sufficient gas flow. Rapid changes in minutes. pressure can trigger the excess flow 3.
WARRANTY Summerset Professional Grills Oven Limited Warranty 5 year warranty on workmanship on The Oven covering construction and materials 3 year warranty on burner 1 year warranty allinternal parts, grates, burner covers, igniter, light and external parts Proof of purchase is required to access this warranty program, which is in effect from the dateof purchase. Customers will be subject to parts, shipping, and handling fees if unable to provideproof of the purchase or after the warranty has expired.
Exploded Diagram For replacement parts, call our customer service department at a.m. – 5 p.m., P ST, Monday to Friday.
Exploded Diagram No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Part Name Heat s pacer Back heat-shield Light assy. Light bracket Handle latch Gas pipe Chimney assy. Cooking grill Smoker box assy. Pizza stone Bottom grill Interior assy. Round burner assy. Exterior Fascia heat shield Oven front panel Back panel Grease tray Electronic igniter Nozzle stator Valve Viewing window Door handle assy. Door heat shield assy.
Replacement Parts 1、BG070 -01 Oven Exterior * 1 pc 2. BG070 -02-00B Oven Interior * 1 pc 3. BG070 -24 Burner Bracket Beam * 1 pc 4. BG070B -03-01 Oven Back Panel * 1 pc 5. BG070 -03A Oven Back Heat Shield * 1 pc 6. BG070 -10-00B Burner Assy. * 1 pc 7. BG070 -18 Cooking Grate * 2 pcs 8. BG070 -17B Base Grate * 1 pc 9. BG070 -32A Pizza Stone * 1 pc 10. BG070 -13-00 Smoker Box * 1 pc 11. BG070 -08-00C Chimney Assy. * 1 pc 12. BG070B -05A Control Fascia * 1 pc 13.
Replacement Parts 25. BG070B -38 Oven Door Glass * 2 pc 26. BG070 -30 Temp. Gauge * 1 pc 27. BG070 -12-00 Oven Door Handle Assy. * 1 pc 28. BG070 -76-00 Sideshelf * 2 pcs 29. BG070B -30-01 Left Sideshelf Bracket * 2 pcs 30. BG070B -30-02 Right Sideshelf Bracket * 2 pcs 31. BG070B -57-00 Oven Left Holder Panel * 1 pc 32. BG070B -58-00 Oven Right Holder Panel * 1 pc 33. BG070B -59 Oven Back Seal Panel Oven Left Holder Panel * 1 pc 34.
Replacement Parts 49. BG070B -53 Trolley Top Panel * 1 pc 50. BG070B -54 Trolley Door Horizontal Beam * 1 pc 51. BG070B -50-00 Trolley Left Sidepanel Assy. * 1 pc 52. BG070B -51-00 Trolley Right Sidepanel Assy. * 1 pc 53. BG070B -52 Trolley Back Panel Assy. * 1 pc 54. BG070B -55 Trolley Door Exterior * 1 pc 55. BG070B -56 Trolley Door Interior * 1 pc 56. BG070 -40 Triangle Bracket * 2 pcs 57. DGP350SNP -30-00 Cylinder Tray Assy. *1 pc 58. BG070 -78-00 Trolley Base Panel Assy. * 1 pc 59.
Replacement Parts Attachthe “installation flanges” to your oven. This will support your oven in the island. (Sold Separately) After your island is made with the correct cut out dimensions, and you have your flanges attached, slide your oven into your cut out. Then plug in r electrical you andconnectgas to your oven.
