MODEL EX13D/ EX17D EX21D/ EX27D PL 2ZZ9990100 PL
7 10 3 2 20 8 EX17, 21 EX27 11 3 4 9 6 3 3
WARNING : The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. NOTICE FEDERAL EMISSION COMPONENT DEFECT WARRANTY and CALIFORNIA EMISSION CONTROL WARRANTY are applicable to only those engines/ generators complied with EPA (Environmental Protection Agency) and CARB (California Air Resources Board) emission regulations in the U.S.A.
FEDERAL EMISSIONS COMPONENT DEFECT WARRANTY EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE – This emission warranty is applicable in all States, except the state ENGLISH of California. Fuji Heavy Industries Ltd. and Robin America Inc., Wood Dale Illinois, (herein “ROBIN AMERICA”) warrant(s) to the initial retail purchaser and each subsequent owner, that this Nonroad engine (herein “engine”) has been designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U.
The California Air Resources Board and Fuji Heavy Industries Ltd. (herein “FUJI”) are pleased to explain the emission control system warranty on your 2005 and later Small Off-Road engine (herein "engine"). In California, the engine must be designed, built and equipped to meet the State's stringent anti-smog standards. FUJI must warrant the emission control system on your engine for the periods of time described below, provided there has been no abuse, neglect or improper maintenance of your engine.
ENGLISH When warranty repair is needed, the engine must be brought to an authorized service dealer or warranty station’s place of business during normal business hours. In all cases, a reasonable time, not to exceed 30 days, must be allowed for the warranty repair to be completed after the engine is received by the authorized service dealer or warranty station. JP G.
FOREWORD Thank you very much for purchasing a ROBIN ENGINE. Your ROBIN ENGINE can supply the power to operate various sorts of machines and equipment. Please take a moment to familiarize yourself with the proper operation and maintenance procedures in order to maximize the safe and efficient use of this product. Keep this owner’s manual at hand, so that you can refer to it at any time.
1. SAFETY PRECAUTIONS Please make sure you review each precaution carefully. Pay special attention to statement preceded by the following words. WARNING “WARNING” indicates a strong possibility of severe personal injury or loss of life if instructions are not followed. CAUTION “CAUTION” indicates a possibility of personal injury or equipment damage if instructions are not followed. WARNING : EXHAUST PRECAUTIONS ■ Never inhale exhaust gasses.
■ Do not touch the spark plug and ignition cable when starting and operating the engine. ■ Never make adjustments on the machinery while it is connected to the engine, without first removing the ignition cable from the spark plug. Turning the crankshaft by hand during adjusting or cleaning might start the engine, and cause serious injury to the operator. ■ Operate the engine on a stable, level surface. If the engine is tilted, fuel spillage may result.
SYMBOLS Read the owner's manual. Stay clear of the hot surface. Exhaust gas is poisonous. Do not operate in an unventilated area. Stop the engine before refueling. US Fire, open flame and smoking prohibited. On (Run) Plus ; Positive polarity Off (Stop) Battery Engine oil Engine start (Electric start) Add oil 2. COMPONENTS (See Fig. 1) NOTE Please refer to the illustrations on the back page of the front cover or back cover for Fig. 1 to 8 indicated in the sentence.
3. PRE-OPERATION CHECKS NOTE Engine shipped from our factory is without oil. Before starting engine, fill with oil. Do not over-fill. 4. ELECTRIC STARTER MODELS For electric starter operation, proper electric wiring arrangements are needed before normal engine operation. 1. BATTERY ■ Use a battery rated 12V-24AH or larger. 1. CHECK ENGINE OIL (See Fig. 2) Before checking or refilling engine oil, be sure the engine is located on stable, level surface and stopped.
4. WIRING WIRING DIAGRAM (ELECTRIC STARTER MODELS) MAGNETIC SWITCH CABLE To LED Lamp Spark plug Black To KEY SWITCH (TERMINAL "ST") Oil sensor control unit Ignition coil Magneto EARTH WIRE Charge coil Key switch Diode rectifier +M -M AC ST B BATTERY LA306 LA106 LA406 Oil sensor Battery EX27 (1) Connect positive (+) terminal of the magnetic switch and US To Key switch (B) To Diode rectifier LA108 LA408 positive (+) terminal of the battery with battery cable.
■ Metric keyway-type crankshaft Washer; Use the washer (material; SS41P) with the thickness described below; EX13/17/21 Washer Thickness EX27 4.5 mm or over 020-00801-40, ROBIN genuine part Washer Thickness; 4.5 mm OD; 28 mm ID; 8.5 mm Material; SS41P Key Location When using the belt pulley with the extended boss on both side as shown in the illustration, put the spacer so that the key stays in the keyway portion of the crankshaft. Proper Key should be within this portion.
6. OPERATING YOUR ENGINE (See Fig. 4) 1. STARTING (1) Open the fuel cock. (See Fig.4-q) 2. RUNNING (1) After the engine starts, set the speed control lever at the low speed position (L) and warm it up without load for a few minutes. (See Fig.5-q) (2) Turn the STOP SWITCH to the position “ I ” (ON). (See Fig.4-w) (2) Gradually move the speed control lever toward the high (3) Set the speed control lever 1/3 of the way towards the speed position (H) and set it at the required engine high speed position.
7. MAINTENANCE (See Fig. 7) 7-q q) 1. DAILY INSPECTION (See Fig.7 (4) Air cleaner elements Before running the engine, check the following service items. (5) Spark plug q Loose or broken bolts and nuts (6) Magneto or electronic ignition system w Clean air cleaner element (7) Spark advance/ retard system, if applicable e Enough clean engine oil (8) Exhaust manifold, if applicable.
e,r r) 4. ENGINE OIL CHANGE (See Fig. 7-e Initial oil change Thereafter ■ Paper Element Cleaning (See Fig.7-u-w) Clean by tapping gently to remove dirt and blow off dust. : After 20 hours of operation : Every 100 hours of operation Never use oil. Clean the paper element every 50 hours of operation, and replace element set every 200 hours. (1) When changing oil, stop the engine and loosen the drain plug. Drain the used oil while the engine is warm. Warm C.
8. PREPARATIONS FOR STORAGE 7. FUEL HOSE REPLACEMENT 7-!1 !1) (See Fig.7 WARNING Take extreme caution when replacing fuel hose ; gasoline is extremely flammable. q) 8-q 1. DISCHARGE FUEL (See Fig.8 WARNING If you do not use the engine more than 1 month, discharge fuel to prevent gum in the fuel system and carburetor parts. ■ Remove the fuel cup, place it over a container and open the fuel cock to discharge fuel from the fuel tank. Replace the fuel hose every 2 years.
10. SPARK ARRESTER (OPTIONAL) In a dry or wooded area, it is recommendable to use the engine with a spark arrester. Some areas require the use of 11. EASY TROUBLESHOOTING WHEN ENGINE WILL NOT START : a spark arrester. Please check your local laws and Perform the following checks before you take the engine to regulations before operating your engine. your Robin dealer. If you still have trouble after completing the checks, take the engine to your nearest Robin dealer.
12. SPECIFICATIONS MODEL EX13D Type Displacement EX17D EX21D EX27D Air-cooled, 4-cycle single cylinder, overhead camshaft, gasoline engine mL (cc) 126 169 211 265 Continuous Output kW/rpm (HP/rpm) 2.2/3600 (3.0/3600) 2.9/3600 (4.0/3600) 3.7/3600 (5.0/3600) 5.1/3600 (7.0/3600) Maximum Output kW/rpm (HP/rpm) 3.2/4000 (4.3/4000) 4.2/4000 (5.7/4000) 5.1/4000 (7.0/4000) 6.6/4000 (9.0/4000) Direction of Rotation Counterclockwise, as Viewed from P.T.O.
ISSUE EMD-EU2135 産業機器カンパニー 〒364-8511 埼玉県北本市朝日4-410 カスタマーサービス部 技術サービス課 TEL 048-593-7857 FAX 7965 営業統括部 部品課 TEL 048-593-7780 FAX 7797 営業第三部 国内エンジン営業課 TEL 048-593-7847 FAX 7948 PRINTED IN JAPAN August 05 CE-