ITEM #1210978 LIGHTED MIRROR MODEL #MIR7191 Style Selections® is a registered trademark of LF, LLC. All Rights Reserved. Français p. 12 Español p. 23 ATTACH YOUR RECEIPT HERE 800413 Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-888-8225, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. 5 p.m., EST, Friday.
TABLE OF CONTENTS Package Contents ...............................................................................................................2 Hardware Contents ......................................................................................................................... 3 Safety Information ...............................................................................................................3 Preparation ..............................................................................
HARDWARE CONTENTS (shown actual size) AA BB CC DD Fixture Screw Plastic Anchor Wire Connector Machine Screw Qty. 4 Qty. 4 Qty. 3 Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. For installation options not covered in this manual, consult a qualified electrician. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product.
SAFETY INFORMATION • To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this light fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture. If your house wire is larger than 12-gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.
SAFETY INFORMATION CAUTION • TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by removing the fuse (or switching the circuit breaker off). • If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture. Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
INITIAL INSTALLATION 2. Determine the approximate location for the fixture (A). Place a template (not included) against the wall, and mark the location of the holes using a pencil or a marker (not included). 2 Template Template Pilot Hole If mounting surface is wood, use a 5/64 in. drill bit (not included) to drill the fixture screws (AA) in wood at marked locations. Proceed to one of the two installation options (Plug-In or Hardwire). If mounting surface is drywall, use a 5/16 in.
PLUG-IN INSTALLATION 2. Hang fixture (A) using the keyhole slots on the back of fixture (A). 2 A Keyhole Slot 3. Insert the power cord (C) preassembled on fixture (A) into proper wall outlet. 3 WARNING: The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no circumstances must the grounding prong be cut off the plug.
HARDWIRE INSTALLTION 2. Remove the preassembled wire connectors to discharge the power cord (C). 2 Wire Connectors C 3. Inside the wire box, remove ONLY the plastic piece from the power cord (C), so the power cord (C) can be removed from the fixture (A). 3 Wire Box Pull power cord (C) from the bottom of the wire box. NOTE: Do not remove the other plastic piece placed on the main wire insulation. C Plastic Piece 4.
HARDWIRE INSTALLTION 5. Prepare wires by stripping 3/4 in. of insulation from wire ends using wire strippers (not included). Connect WHITE wire from fixture (A) to WHITE wire from outlet box using existing wire connector or wire connector (CC). Connect BLACK wire from fixture (A) to BLACK wire from outlet box using existing wire connector or wire connector (CC). Connect BARE/GREEN ground wire from outlet box to BARE ground wire from fixture (A) with wire connector (CC).
HARDWIRE INSTALLTION 7. Attach the wire box cover to outlet box (not included) using outlet box screws or the machine screws (DD). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (DD), consult a licensed electrician before proceeding. Tighten machine screws (DD) to secure wire cover box. 7 Wire box cover DD CAUTION: Make sure the outlet box can support 35 lbs. hanging weight. Use metal outlet box; plastic outlet boxes are not recommended.
OPERATING INSTRUCTIONS 1. Tapping the touch sensor (B) on fixture (A) turns light ON and OFF. 2. Pressing the touch sensor (B) for 3 seconds dims the light. B A CARE AND MAINTENANCE • Wipe fixture with soft, damp cloth. Do not use an abrasive cleaner on fixture. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM Light does not come on initially or no longer comes on. POSSIBLE CAUSE CORRECTIVE ACTION 1. Power is OFF. 2. Faulty connection. 3.
