2V Smart Charger: 2-Stage Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This charger is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use This Strongway 12V Smart Charger is suitable for 12V Lead-Acid batteries. The charger will charge the vehicle battery and keep the battery performing optimally. Packaging Contents Abbreviations and Acronyms A Ampere AC Alternating Current Ah Amp-hours DC Direct Current mA Milli-Ampere V Volt LED Light-Emitting Diode LCD Liquid Crystal Display Technical Specifications Property Input Output Working Temperature Specification 120V AC, 0.
product will be safer and do a better job at the capacity for which it was intended. DO NOT use this equipment for a purpose for which it was not intended. Industrial or commercial applications must follow OSHA requirements. ⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury.
Do not use a product with a malfunctioning switch. Any power tool that cannot be controlled with the power switch is dangerous and must be repaired by an authorized service representative before using. Disconnect the power/air supply from the product and place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store the product when it is not in use.
those used in cars, trucks, RV’s, trolling motors, etc., as this could result in personal injury or property damage due to battery explosion. Do not charge a frozen battery. Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
Double Insulated Tools: Tools with Two-Prong Plugs Tools marked Double Insulated do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration.
Before Each Use ⚠WARNING To prevent serious injury and property damage read and understand the owner’s manual before usin Avoid touching your eyes while working with a battery. Have plenty of fresh water and soap nearby for use in case battery acid contacts your eyes, skin or clothing. If this happens, wash immediately with soap and water, and then get medical attention. Risk of explosion. Batteries contain acid and produce explosive gases.
Clean the battery terminals. Be careful to keep corrosion or battery acid from getting in or around your eyes. For batteries with removable vent caps, if required, add distilled water to each cell until the battery fluid reaches the level specified by the battery manufacturer. Do not overfill. For batteries without removable vent caps, carefully follow the manufacturer’s charging instructions.
Interference NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Reference Part Number Part Description Quantity 4 56765-04 Manual 1 Image Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
