CLAWFOOT BATHTUB SERIES OWNER'S MANUAL & INSTALLATION GUIDE READ ENTIRE INSTALLATION GUIDE PRIOR TO INSTALLING THE BATHTUB THIS BATHTUB SHOULD ONLY BE INSTALLED BY A CERTIFIED PLUMBER CAUTION! TWO PEOPLE ARE REQUIRED TO LIFT THE BATHTUB QUESTIONS ON PRODUCT, INSTALLATION, RETURNS? PLEASE CONTACT streamlinebath.com support@streamlinebath.
PRIOR TO INSTALLING These products must be installed by a fully insured and licensed plumber only. Installation of any product by anyone other than fully insured and licensed plumber shall void limited warranty. We are not responsible for any local code compliance for this product. Building and plumbing codes may vary state-to-state. Streamline shall not be held liable for any and all incidental damages or flood caused due to use of this product.
DRAIN MODEL COMPATIBILITY FREESTANDING BATHTUB N-DWF-CH N-DWF-GLD N-100-60CFWH-DM N-101-68CFWH-DM N-102-60CFRD-DM N-103-68CFBL-DM N-340-67CFWH-FM N-341-59CFWH-FM N-342-63CFWH-FM N-343-55CFWH-FM N-344-59CFBL-FM N-345-67CFBL-FM N-860-60CFGR-FM N-861-68CFWH-FM N-900-60CFWH-DM N-901-68CFWH-DM N-920-60CFWH-FM N-921-68CFGR-FM N-480-61FSHW-FM N-1020-62CFWH-FM N-1021-62CFRD-FM N-1080-59CFWH-FM N-1081-67CFWH-FM N-1100-59CFWH-FM N-1101-67CFGR-FM N-481-61FSBL-FM N-482-61FSRD-FM N-1120-59CFBL-DM N-1121-67C
WHAT'S INCLUDED IN THE CLAWFOOT BOX Applicable models : Applicable models: N-CFL1775-CH N-CFL1775-WH N-CFL1775-BL N-CFL1775-GLD N-CFL1912-CH N-CFL1912-WH N-CFL1912-BL N-CFL1912-GLD N-CFL11603-CH N-CFL11603-GLD 1 N-CFL11603-BL N-CFL11603-WH N-CFLK36572-BL N-CFLK36572-CH N-CFLK36572-GLD N-CFLK35672-WH N-CFL46572-BL N-CFL46572-WH N-CFL46572-GLD N-CFL46572-CH 2 N-CFL11601-CH N-CFL11601-WH N-CFL11601-BL N-CFL11601-GLD 3 1 4 6 5 2 7 4 No.
DRAIN DIAGRAMS No.
CLAWFOOT DIRAGRAM 1 1 2 3 2 3 4 4 5 2 6 6 7 No. 5 6 ITEM 3 8 7 Qty No.
BATHTUB INSTALLATION 1. Ensure that the floor at the installation site has sufficient floor support and is level. 2. Waterproofing the floor is highly recommended. 3. Determine the location of the drainpipe on the floor by taking measurements of the drain and waste location underneath the unit. Clean the drain hole area in preparation of setting the drain. The area should be dry & free from any debris. 4. Remove the bathtub from its box.
5. Gently place the bathtub in the upside-down position on a tarp or cardboard sheet in order to avoid contact with any rough surface. 6. This step will be attaching the clawfeet to the bathtub. Please check the previous page to see which clawfeet model is applicable to your bathtub.
d) Place the metal plate on top of the bolts that are already on the bottom of the bathtub. e) Make sure to adjust the metal plate so that it fits snug with the bolts on the bathtub. This will help to ensure that the clawfeet are placed correctly and are functioning properly. d) Remove the safety caps from the bolts on the bathtub. e) Place the metal plate [#2] over the bolts on the bathtub as shown in the diagram below.
h) Check to ensure that the clawfoot is aligned properly with the bathtub and is sitting snug against the bathtub. Once this is done, use a wrench to tighten all of the nuts. h) Take (1) washer [#5] and place it over the bolt on the metal plate. Then take (1) nut with washer [#6] and screw it into the bolt. Do not tighten. Repeat the same step for the lower bolt. Once this is done, use a wrench to tighten all of the nuts. i) Repeat the same procedure for the other 3 legs.
9. Assemble the tee section to the tailpiece, overflow, & drain ell using the coupling nuts and O-rings that are provided. Tee Overflow Ell O Ring Coupling Nut 10 . Attach the tapered rubber gasket to the overflow ell. Align the overflow ell with the overflow hole & secure the drain to the tub with overflow plate and screw provided. Tapered Rubber Gasket Overflow Plate 11 . Make sure a watertight seal exists on all bath drain connections.
The installation steps below are for drain model A1840-0. Strainer Rubber Gasket A1840-0 Flat Rubber Gasket 7 Connector 12. Put the rubber gasket (#4) onto the strainer (#3) 13. Put the rubber gasket and strainer through the pre-drilled drain hole. 14. Put the flat rubber gasket (#5) onto the connector (#7). 15. Connect the connector with the flat rubber gasket, strainer, and rubber gasket and tighten them by hand. Then use a wrench to tighten the connector.