Installation Sheet

x2
Reversible
B
"B" Mark
Cut Line
1/32"
(1 mm)
B
Top Track
x2
#8-18 x 2"
Screw
Cover
Screw Cover
x2
1
2
3
Groove
Tin Snips
Miter Box
32 Teeth Per Inch Blade
Masking Tape
100% Silicone Sealant
1/16"
Series Number
Label
1077762
Anchor
1081001
Bumper
1031943**
Screw Cover
1205305**
Hanger Bracket Kit
1203634
Hardware Skin Pack
1058827-02**
Top Track
1051142-A
Screw
#8-32 x 3/8"
1199426-01**
Hanger Bracket
1050048-B
Barrel Nut
1077763-A
Bolt
#8-32 x 1/4"
Wall Jamb*
1093027
Spacer (8 ea.)
1044585
Roller
Door Panel*
1057704-02** [20" (508 mm)]
1057704-01** [24" (610 mm)]
Towel Bar
1056868-A
Screw
1048208-N
Screw
#8-18 x 2"
1058294**
Center Guide
1058626-11** (SP5475-57)
1058626-12** (SP5465-45)
Bottom Track
1053530
Insert
1199110
Gasket
Leg
Insert
Bottom Track
Correct Incorrect
Mark
Center
Punch
Slide the notched end of the insert into the
groove and pull the notch to the end of the
bottom track. Trim the insert to be flush with the
bottom track.
Center the bottom track on the ledge with the leg
to the outside. Tape the bottom track in place and
mark the position.
Position the wall jambs over the bottom track.
Plumb both wall jambs. Mark the screw holes.
Tile Installations Only
Nick the tile at the mark for the hole before
drilling with a center punch. This keeps the drill
bit from moving as the hole is started.
When installing to a tile wall, first drill a small
diameter hole, then a larger hole.
Install anchors. Do not install the screws directly
into the tile, as this may crack the tile.
When drilling, use a masonry bit.
Remove the wall jambs. Drill 5/16” holes into the
walls and insert the anchors.
Apply silicone sealant in the groove on the
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
Reposition both wall jambs. Secure the wall
jambs with screws. Attach a bumper at the top
and bottom locations.
Check the bumpers for the correct horizontal
alignment with the wall jambs.
Measure distance “B” above the wall jambs.
Subtract 1/32” (1 mm) or the width of a saw
blade from “B.” Mark and cut the top track.
Position the top track over the wall jambs. Either
side of the top track may face out.
SP5400 Series Sliding Shower and Bath Doors
Sliding Shower Doors
11204890-2-D
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310
1204890-2-D
Installation and Care Instructions
Required Tools Parts Identifi cation
2 3 4
7 86 9
1 5
10
SterlingPlumbing.com
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
IMPORTANT! Do not touch the edges of the tempered glass with tools or
any other hard objects. Do not set the unframed tempered glass directly on
the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the bottom track.
NOTICE: The warranty does not apply to a product that has been modified
or altered in a manner other than as expressly permitted in the Installation
and Care Guide.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for application and
curing time.
To watch this installation video online, visit www.sterlingplumbing.com.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Critical Information!
Read Before Installation!
Read and follow all instructions.
*Need help? Contact the STERLING Customer Care Center at 1-800-STERLING
(1-800-783-7546).
For service parts information, care and cleaning, and other information, visit
www.sterlingplumbing.com
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________